6 Removal and replacement procedures for authorized service provider parts
This chapter provides removal and replacement procedures for authorized service provider parts.
IMPORTANT: Components described in this chapter should be accessed only by an authorized service provider. Accessing these parts can damage the computer or void the warranty.
NOTE: Details about your computer, including model, serial number, product key, and length of warranty, are on the service tag at the bottom of your computer.
Component replacement procedures
To remove and replace computer components, use these procedures.
NOTE: HP continually improves and changes product parts. For complete and current information about supported parts for your computer, go to http://partsurfer.hp.com
, select your country or region, and then follow the on-screen instructions.
You must remove, replace, or loosen as many as 50 screws when you service the parts described in this chapter. Make special note of each screw size and location during removal and replacement.
Preparation for disassembly
To remove and replace computer components, use these procedures.
See
Removal and replacement procedures preliminary requirements on page 28
for initial safety procedures.
1.
Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
2.
Disconnect the power from the computer by unplugging the power cord from the computer.
3.
Disconnect all external devices from the computer.
Battery
To remove the battery, use this procedure and illustration.
Table 6-1 Battery description and part number
Description
Battery, 3 cell, 53 Whr
Spare part number
L78555-002
43
WARNING!
To avoid personal injury and damage to the product:
● Do not puncture, twist, or crack the battery.
● Do not cause an external puncture or rupture to the battery. They can cause a short inside the battery, which can result in battery thermal runaway.
● Do not handle or touch the battery enclosure with sharp objects such as tweezers or pliers, which might puncture the battery.
● Do not compress or squeeze the battery case with tools or heavy objects stacked on top of the case.
These actions can apply undue force on the battery.
● Do not touch the connectors with any metallic surface or object, such as metal tools, screws, or coins, which can cause shorting across the connectors.
Before removing the battery, follow these steps:
1.
Prepare the computer for disassembly ( Preparation for disassembly on page 33 ).
2.
Remove the bottom cover (
Bottom cover on page 33
).
WARNING!
To reduce potential safety issues, use only the user-replaceable battery provided with the computer, a replacement battery provided by HP, or a compatible battery purchased from HP.
IMPORTANT: Removing a battery that is the sole power source for the computer can cause loss of information. To prevent loss of information, save your work or shut down the computer through Windows before you remove the battery.
Remove the battery:
1.
Remove the speaker cable from the clips along the bottom of the battery (1).
2.
Disconnect the battery cable from the system board (2).
3.
Remove the four Phillips M2.0 × 4.0 screws (3) that secure the battery to the computer.
44 Chapter 6 Removal and replacement procedures for authorized service provider parts
4.
Remove the battery from the computer (4).
To insert the battery, reverse the removal procedures.
RTC battery
To remove the RTC battery, use this procedure and illustration.
Table 6-2 RTC battery description and part number
Description
RTC battery
Before removing the RTC battery, follow these steps:
1.
Prepare the computer for disassembly (
Preparation for disassembly on page 33
).
2.
Remove the bottom cover ( Bottom cover on page 33 ).
3.
Remove the battery (see Battery on page 43 ).
Remove the RTC battery:
1.
Disconnect the battery cable from the system board (1).
Spare part number
L13694-001
Component replacement procedures 45
2.
Use a tool (2) to release the battery from the computer (3).
Reverse this procedure to install the RTC battery.
Speakers
To remove the speakers, use this procedure and illustration.
Table 6-3 Speaker description and part number
Description
Speaker Kit
Spare part number
M07107-001
Before removing the speakers, follow these steps:
1.
Prepare the computer for disassembly ( Preparation for disassembly on page 33 ).
2.
Remove the bottom cover (
Bottom cover on page 33
).
3.
Disconnect the battery cable from the system board (see
Battery on page 43
).
Remove the speakers:
1.
Disconnect the speaker cable from the system board (1).
2.
Remove the cable between the speakers from the clips along the bottom of the battery (2).
46 Chapter 6 Removal and replacement procedures for authorized service provider parts
3.
Remove the speakers from the computer (3) .
Reverse this procedure to install the speakers.
Card reader board
To remove the card reader board, use this procedure and illustration.
Table 6-4 Card reader board description and part number
Description
Card reader board
Card reader board cable (included in Cable Kit)
Before removing the card reader board, follow these steps:
1.
Prepare the computer for disassembly (
Preparation for disassembly on page 33
).
2.
Remove the bottom cover ( Bottom cover on page 33 ).
3.
Remove the battery (see Battery on page 43 ).
4.
Remove the left speaker (see
Speakers on page 46 ).
Remove the card reader board:
1.
Disconnect the cable from the reverse ZIF connector on the card reader board (1).
2.
Remove the three Phillips M2.0 × 2.0 screws (2) that secure the board to the computer.
Spare part number
M07105-001
M07101-001
Component replacement procedures 47
3.
Remove the board from the computer (3).
Reverse this procedure to install the card reader board.
Power connector cable
To remove the power connector cable, use this procedure and illustration.
Table 6-5 Power connector cable description and part number
Description
Power connector cable
Spare part number
M15626-001
Before removing the power connector cable, follow these steps:
1.
Prepare the computer for disassembly ( Preparation for disassembly on page 33 ).
2.
Remove the bottom cover (
Bottom cover on page 33
).
3.
Disconnect the battery (see Battery on page 43 ).
Remove the power connector cable:
1.
Disconnect the cable from the system board (1), and then remove the cable from the clip (2).
2.
Remove the Phillips M2.0 × 4.0 screw (3) that secures the power connector cable to the computer.
48 Chapter 6 Removal and replacement procedures for authorized service provider parts
3.
Remove the power connector cable from the computer (4).
Reverse this procedure to install the power connector cable.
USB board
To remove the USB board, use this procedure and illustration.
Table 6-6 USB board description and part number
Description
USB board
USB board cables (included in Cable Kit)
USB bracket (included in Bracket Kit)
Spare part number
M07207-001
M07101-001
M07145-001
Before removing the USB board, follow these steps:
1.
Prepare the computer for disassembly (
Preparation for disassembly on page 33
).
2.
Remove the bottom cover ( Bottom cover on page 33 ).
3.
Disconnect the battery cable from the system board (see Battery on page 43 ).
Remove the USB board:
1.
Disconnect the smaller cable from the USB board (1).
2.
Disconnect the larger cable from the ZIF connector on the USB board (2).
3.
Remove the three Phillips M2.0 × 4.0 screws (3) that secure the board to the computer, and then remove the bracket from the board (4).
Component replacement procedures 49
4.
Remove the board from the computer (5).
Reverse this procedure to install the USB board.
Fingerprint reader board
To remove the fingerprint reader board, use this procedure and illustration.
Table 6-7 Fingerprint reader board description and part number
Description
Fingerprint reader board
Fingerprint reader board cable (included in Cable Kit)
Fingerprint reader board bracket (included in Bracket Kit)
Spare part number
M07151-001
M07101-001
M07145-001
Before removing the fingerprint reader board, follow these steps:
1.
Prepare the computer for disassembly ( Preparation for disassembly on page 33 ).
2.
Remove the bottom cover (
Bottom cover on page 33
).
3.
Remove the battery (see
Battery on page 43
).
Remove the fingerprint reader board:
1.
Remove the Phillips M2.0 × 2.0 screw (1) that secures the fingerprint reader bracket to the computer, and then remove the bracket (2).
2.
Disconnect the cable from the ZIF connector on the fingerprint reader board (3).
50 Chapter 6 Removal and replacement procedures for authorized service provider parts
3.
Remove the fingerprint reader board from the computer (4).
Reverse this procedure to install the fingerprint reader board.
Touchpad
To remove the touchpad, use this procedure and illustration.
Table 6-8 Touchpad description and part number
Description
Touchpad button board for use in models with discrete graphics memory
Touchpad button board for use in models with UMA graphics memory
Touchpad
Touchpad with NFC antenna
Touchpad cable (included in Cable Kit)
Before removing the touchpad, follow these steps:
1.
Prepare the computer for disassembly (
Preparation for disassembly on page 33
).
2.
Remove the bottom cover ( Bottom cover on page 33 ).
3.
Remove the battery (see Battery on page 43 ).
Remove the touchpad:
1.
Disconnect the system board cable from the ZIF connector on the touchpad (1).
2.
Disconnect the middle cable from the ZIF connector on the touchpad (2).
3.
Disconnect the touchpad button board cable from the ZIF connector on the touchpad (3).
4.
Disconnect the cable from the ZIF connector on the system board (4).
5.
Remove the four Phillips M1.6 × 1.8 screws (5) that secure the touchpad to the computer.
Spare part number
M07148-001
M07147-001
M07149-001
M07150-001
M07101-001
Component replacement procedures 51
6.
Lift the metal tape (6), and then remove the touchpad from the computer (7).
7.
Disconnect the cable from the reverse ZIF connector on the NFC module (1).
8.
Peel the system board cable from the side of the touchpad (2).
9.
Remove the five Phillips M1.6 × 1.8 screws (3) that secure the touchpad to the computer.
10.
Remove the touchpad from the computer (4).
Reverse this procedure to install the touchpad.
52 Chapter 6 Removal and replacement procedures for authorized service provider parts
NFC module
To remove the NFC module, use this procedure and illustration.
Table 6-9 NFC module description and part number
Description
NFC module
NFC module cable (included in Cable Kit)
Spare part number
M07214-001
M07101-001
Before removing the NFC module, follow these steps:
1.
Prepare the computer for disassembly (
Preparation for disassembly on page 33
).
2.
Remove the bottom cover ( Bottom cover on page 33 ).
3.
Remove the battery (see Battery on page 43 ).
Remove the NFC module:
1.
Disconnect the system board cable from the ZIF connector on the NFC module (1).
2.
Disconnect the touchpad cable from the reverse ZIF connector on the NFC module (2).
3.
Use a tool to release the module (3), and then remove the module from the computer (4). The module is secured with adhesive.
Reverse this procedure to install the NFC module.
Fan
To remove the fan, use this procedure and illustration.
Component replacement procedures 53
Table 6-10 Fan description and part number
Description
Fan assembly for use in models with discrete graphics memory
Fan assembly for use in models with UMA graphics memory
Spare part number
M07144-001
M07102-001
Before removing the fan, follow these steps:
1.
Prepare the computer for disassembly ( Preparation for disassembly on page 33 ).
2.
Remove the bottom cover (
Bottom cover on page 33
).
3.
Disconnect the battery cable from the system board (see
Battery on page 43
).
Remove the fan assembly:
1.
Remove the cables from the clips on the side of the fan (1).
2.
Disconnect the fan cable from the system board (2).
3.
Loosen the two captive Phillips screws (3) that secure the fan to the computer, and then remove the fan from the computer (4).
Reverse this procedure to install the fan assembly.
Heat sink
To remove the heat sink, use these procedures and illustrations.
Table 6-11 Heat sink descriptions and part numbers
Description
Heat sink for use in models with discrete graphics memory
Heat sink for use in models with UMA graphics memory
Before removing the heat sink, follow these steps:
54 Chapter 6 Removal and replacement procedures for authorized service provider parts
Spare part number
M07143-001
M07204-001
1.
Prepare the computer for disassembly (
Preparation for disassembly on page 33
).
2.
Remove the bottom cover ( Bottom cover on page 33 ).
3.
Disconnect the battery cable from the system board (see Battery on page 43 ).
Remove the heat sink:
1.
To remove the heat sink on models with UMA graphics memory: a.
In the order indicated on the heat sink, loosen the four captive Phillips screws (1) that secure the heat sink to the computer.
b.
Remove the heat sink from the computer (2).
Component replacement procedures 55
c.
Thoroughly clean the thermal material from the surfaces of the heat sink and the system board components each time the heat sink is removed. Replacement thermal material is included with the heat sink and system board spare part kits. The following illustration shows the replacement thermal material locations.
Thermal material is used on the system board component (1) and on the heat sink area (2) that services it.
2.
To remove the heat sink on models with discrete graphics memory: a.
In the order indicated on the heat sink, loosen the six captive Phillips screws (1) that secure the heat sink to the computer.
b.
Remove the heat sink from the computer (2).
56 Chapter 6 Removal and replacement procedures for authorized service provider parts
c.
Thoroughly clean the thermal material from the surfaces of the heat sink and the system board components each time the heat sink is removed. Replacement thermal material is included with the heat sink and system board spare part kits. The following illustration shows the replacement thermal material locations.
Thermal material is used on the system board components (1) (3) (5) and on the heat sink areas
(2) (4) (6) that service them.
Reverse this procedure to install the heat sink.
System board
To remove the system board, use these procedures and illustrations.
Table 6-12 System board descriptions and part numbers
Description
System board (includes processor):
All system boards use the following part numbers: xxxxxx-001: Non-Windows operating system xxxxxx-601: Windows 10 operating system
Models with discrete graphics memory and integrated system memory
Intel Core i7-10810 processor (OSR) and 32 GB of integrated system memory
Intel Core i7-10810 processor and 32 GB of integrated system memory
Intel Core i7-10810 processor and 16 GB of integrated system memory
Intel Core i7-10610 processor and 32 GB of integrated system memory
Intel Core i7-10610 processor (OSR) and 16 GB of integrated system memory
Intel Core i7-10610 processor and 16 GB of integrated system memory
Intel Core i7-10510 processor and 32 GB of integrated system memory
Spare part number
M07122-xx1
M07121-xx1
M07120-xx1
M07119-xx1
M07118-xx1
M07117-xx1
M07113-xx1
Component replacement procedures 57
Table 6-12 System board descriptions and part numbers (continued)
Description
Intel Core i7-10510 processor and 16 GB of integrated system memory
Intel Core i5-10310 processor (OSR) and 16 GB of integrated system memory
Intel Core i5-10310 processor and 16 GB of integrated system memory
Intel Core i5-10310 processor and 8 GB of integrated system memory
Intel Core i5-10210 processor and 16 GB of integrated system memory
Intel Core i5-10210 processor and 8 GB of integrated system memory
Models with UMA graphics memory
System board with integrated Intel Core i7-10810 processor (OSR)
System board with integrated Intel Core i7-10710 processor
System board with integrated Intel Core i7-10610 processor
System board with integrated Intel Core i7-10610 processor (OSR)
System board with integrated Intel Core i7-10510 processor
System board with integrated Intel Core i5-10310 processor
System board with integrated Intel Core i5-10310 processor (OSR)
System board with integrated Intel Core i5-10210 processor
Before removing the system board, follow these steps:
1.
Prepare the computer for disassembly ( Preparation for disassembly on page 33 ).
2.
Remove the bottom cover (
Bottom cover on page 33
).
3.
Remove the battery (see
Battery on page 43
).
4.
Remove the fan (see Fan on page 53 ).
When you replace the system board, be sure to remove the following components (as applicable) from the defective system board and install them on the replacement system board:
● Memory modules (see
Memory modules on page 34 ).
● WLAN module (see
WLAN module on page 37
).
●
WWAN module (see WWAN module on page 38 ).
● Solid-state drive (see
Solid-state drive on page 40
).
● Heat sink (see
Heat sink on page 54 ).
Remove the system board:
NOTE: System board appearance might vary.
1.
Disconnect the following cables from the system board:
Spare part number
M07112-xx1
M07115-xx1
M07114-xx1
M07116-xx1
M07110-xx1
M07111-xx1
M08564-xx1
M08563-xx1
M08561-xx1
M08562-xx1
M08558-xx1
M08559-xx1
M08560-xx1
M08557-xx1
58 Chapter 6 Removal and replacement procedures for authorized service provider parts
● Power connector cable (1)
● Camera cable (2)
● Antenna cables from the WWAN module (select products only) (3)
● Antenna cables from the WLAN module (4)
● Larger USB cable from the USB board (ZIF) (5)
● Speaker cable (6)
● Small USB cable from the USB board (7)
● Display cable (8)
● Keyboard cable (ZIF) (9)
● Card reader cable (ZIF) (10)
● Touchpad cable (ZIF) (11)
● Keyboard backlight cable (ZIF) (select products only) (12)
● RTC battery cable (13)
● NFC module cable (ZIF) (select products only) (14)
● Fingerprint reader cable (ZIF) (select products only) (15)
Component replacement procedures 59
2.
Remove the four Phillips M2.0 × 4.0 screws (1) that secure the bracket to the system board, and then remove the bracket (2).
The plastic bracket is available in the Plastics Kit as spare part number M07215-001.
3.
Remove the two Phillips M2.0 × 4.0 screws (1) and the three Phillips M2.0 × 2.0 screws (2) that secure the system board to the computer.
4.
Remove the SIM card insert from the computer (3).
60 Chapter 6 Removal and replacement procedures for authorized service provider parts
5.
Lift the side of the system board upward (1), and then pull the system board away from the connectors on the side of the computer to remove it (2).
Reverse this procedure to install the system board.
Display assembly
To remove and disassemble the display assembly, use these procedures and illustrations.
Full hinge-up displays are not available as spare parts. Spare parts for displays are available only at the subcomponent level.
Before removing the display panel, follow these steps:
1.
Prepare the computer for disassembly (
Preparation for disassembly on page 33
).
2.
Remove the bottom cover ( Bottom cover on page 33 ).
3.
Disconnect the battery cable from the system board (see Battery on page 43 ).
4.
Remove the power connector cable ( Power connector cable on page 48
).
Remove the display assembly:
1.
Disconnect the display cable (1) and remove it from the clip (2).
2.
Disconnect the antenna cables from the WWAN module (3), and then remove the cables from the clip
(4).
Component replacement procedures 61
3.
Disconnect the antenna cables from the WLAN module (5) and disconnect the left display cable (6), and then remove the cables from the clips along the side of the fan (7).
4.
Remove the six Phillips M2.5 × 4.0 screws (1) that secure the display assembly to the computer.
5.
Rotate the display to open the hinges (2).
6.
Separate the display assembly from the computer (3).
7.
If you need to replace display assembly subcomponents:
62 Chapter 6 Removal and replacement procedures for authorized service provider parts
a.
Release the bezel by flexing and lifting the bottom (1), left and right sides (2), and top (3).
b.
Remove the bezel from the display (4).
Bezels are available as the following spare part numbers:
● M07163-001: IR camera and ambient light sensor
● M07164-001: IR camera
● M07165-001: RGB camera and ambient light sensor
● M07166-001: RGB camera
● M07100-001: Microphone module only (no camera module)
8.
If you need to remove the hinge cover from the display enclosure: a.
Remove the Phillips M1.6 × 3.0 screw (1) that secures the hinge cover to the display.
b.
Starting on the side with the screw, use a tool to release the hinge cover (2), working your way across the display.
c.
Remove the hinge cover from the display (3).
The hinge cover is available in the Hinge Kit as spare part number M07146-001.
Component replacement procedures 63
9.
If you need to remove the hinges from the display enclosure: a.
Remove the three Phillips M2.0 × 10.0 screws (1) from each hinge.
b.
Remove the hinges from the display (2).
The hinges are available in the Hinge Kit as spare part number M07146-001.
10.
If you need to remove the display panel: a.
The display panel is secured to the display enclosure with tape that is installed under the left and right sides of the panel. To remove the panel, use tweezers to grasp the end of the tape (1). While turning the tweezers, wrap the tape around the tweezers (2) as you continue to pull the tape out from behind the display panel (3). You must pull the tape multiple times before it is completely removed.
64 Chapter 6 Removal and replacement procedures for authorized service provider parts
b.
Rotate the display panel over and place it next to the display enclosure (4).
Display panels are available as the following spare part numbers:
M07281-001: 1000 nit panel
M07136-001: 250 nit panel, Touch-on Panel (TOP)
M07133-001: 250 nit panel
M07135-001: 400 nit, UHD panel
M07134-001: 400 nit, FHD panel c.
Lift the tape from the connector on the display panel (1), rotate the locking lever (2), and then disconnect the cable from the panel (3).
Component replacement procedures 65
d.
Remove the panel (4).
11.
When replacing the display panel, follow these steps:
IMPORTANT: Before installing the display panel, be sure to install the display cable to the back of the panel.
a.
Peel the protective layer from the bottom of the adhesive strips (1).
b.
Starting near the bottom of the inside of the display back cover (2), install the adhesive strips by aligning them with the groove on the edge of cover (3).
c.
Peel the protective layer from the top of the adhesive strips (4).
d.
Install the alignment tools onto the upper left and right corners of the display rear cover (5).
66 Chapter 6 Removal and replacement procedures for authorized service provider parts
e.
Insert the top of the panel into the top of the display rear cover (6), and then rotate the panel into place (7). Be sure that the upper corners of the panel are positioned up against the insides of the alignment tools.
f.
Remove the alignment tool.
g.
Replace the bezel by pressing along the bottom, sides, and then top of the bezel to snap it into place.
Component replacement procedures 67
h.
Install temporary rubber spacer strips on the left and right sides of the bezel (1), and hten close the display (2).
i.
Position the computer upside down on a table.
j.
Leave the computer upside down on the table for 20 minutes to allow the adhesive to set.
k.
Position the computer upright on a table.
68 Chapter 6 Removal and replacement procedures for authorized service provider parts
l.
Leave the computer upright on the table for 10 minutes to be sure the panel sits correctly in the display.
m. Open the display and remove rubber spacer strips.
12.
If you need to remove the hub board from the display: a.
Disconnect the display cable from the ZIF connector (1) on the hub board.
b.
Disconnect the camera cable from the ZIF connector (2) on the hub board.
c.
Disconnect the smaller cables from the reverse ZIF connectors on the hub board (3), (4).
d.
Use a tool (5) to release the board from the display rear cover (6).
The hub board is available as spare part number M07211-001 in models with an IR camera and
M07210-001 in models with an RGB camera or microphone module.
Component replacement procedures 69
13.
If you need to remove the ambient light sensor from the display, disconnect the cable from the reverse
ZIF connector on the board (1), and then use a tool (2) to release the sensor from the computer (3).
The ambient light sensor is available as spare part number M07212-001.
14.
If you need to remove the second ambient light sensor from the display, disconnect the cables from the
ZIF connectors on the board (1), and then remove the sensor from the computer (2).
The second ambient light sensor is available as spare part number M07213-001.
70 Chapter 6 Removal and replacement procedures for authorized service provider parts
15.
If you need to remove the microphone board from the display, disconnect the cable from the reverse ZIF connector on the board (1), and then use a tool (2) to release the board from the computer (3).
The microphone board is available as spare part number M07208-001 and M07209-001 for the rearfacing third microphone.
16.
If you need to remove the camera module:
▲ Use a tool (1) to lift up evenly across the module and peel the module up from the display back cover (2), and then disconnect the cable from the reverse ZIF connector on the module (3). The camera module is available as spare part number M07216-001 for RGB cameras and M08549-001 for IR cameras.
NOTE: For installation, note that the cable routes under the camera module before it connects to the module.
Component replacement procedures 71
17.
If you need to remove the display cable, disconnect the cable from the ZIF connector on the hub board
(1), remove the cable from the clips at the bottom of the display back cover (2), and then remove the cable (3).
The display panel cable is available as spare part number M07203-001.
18.
If you need to remove the camera cable, disconnect the cable from the ZIF connector on the hub board
(1), and then peel the cable off the inside of the display back cover to remove it (2).
The camera cable is available in the Cable Kit as spare part number M07101-001.
72 Chapter 6 Removal and replacement procedures for authorized service provider parts
19.
If you need to remove the WLAN antenna cables, peel the antennas off the inside of the display back cover (1), remove the cables from the clips at the bottom of the cover (2), (3), and then remove the antennas and cables (4).
20.
If you need to remove the WWAN antenna cables, peel the antennas off the inside of the display back cover (1), remove the cables from the clips in the back (2) and near the hinge on the display back cover
(3), and then remove the antennas and cables (4).
Component replacement procedures 73
21.
If you need to remove the ambient light sensor cable, disconnect the cable from the ZIF connectors on the ambient light sensor board (1) and hub board (2), and then peel the cable off the inside of the display back cover to remove it (3).
The ambient light sensor cable is available in the Cable Kit as spare part number M07101-001.
74 Chapter 6 Removal and replacement procedures for authorized service provider parts
22.
If you need to remove the second ambient light sensor cables, disconnect the cable from the ZIF connectors on the second ambient light sensor (1) and hub board (2), and then peel the cables off the inside of the display back cover to remove them (3).
The second ambient light sensor cable is available in the Cable Kit as spare part number M07101-001.
Display back covers are available as the following spare part numbers:
M07141-001: Models with WWAN, 250 nits
M07142-001: Models with WWAN, 400 nits or 1000 nits
M07139-001: Models without WWAN, 250 nits
M07140-001: Models without WWAN, 400 nits or 1000 nits
M14632-001: Models with UHD panels
Component replacement procedures 75
23.
Use the following illustration to determine proper cable routing. The WWAN antenna cables and display cable route through the right hinge (1). The WLAN antenna cables and display cable route through the left hinge (2).
Reverse this procedure to reassemble and replace the display assembly.
Keyboard with top cover
The top cover with keyboard remains after removing all other spare parts from the computer. In this section, the first table provides the main spare part number for the top cover/keyboards. The second table provides the country codes.
Table 6-13 Keyboard with top cover descriptions and part numbers
Description Spare part number
Keyboard with top cover for use models with discrete graphics:
Backlit
Backlit, for use in privacy models
Not backlit
For use models with UMA graphics:
Backlit
Backlit, for use in privacy models
Not backlit
M14635-xx1
M14636-xx1
M14634-xx1
M07131-xx1
M07132-xx1
M07130-xx1
Table 6-14 Spare part country codes
For use in country or region
Spare part number
Belgium
Brazil
Bulgaria
Chile
-A41
-201
-261
-161
For use in country or region
Hungary
Iceland
India
Israel
Spare part number
-211
-DD1
-D61
-BB1
For use in country or region
Saudi Arabia
Slovenia
South Korea
Spain
Spare part number
-171
-BA1
-AD1
-071
76 Chapter 6 Removal and replacement procedures for authorized service provider parts
Table 6-14 Spare part country codes (continued)
For use in country or region
Spare part number
For use in country or region
Czech Republic/Slovakia
Denmark
Denmark, Finland, and
Norway
French Canada
Finland/Sweden
France
Germany
Greece
-FL1
-081
-DH1
-DB1
-B71
-051
-041
-151
Italy
Japan
The Netherlands
Northern Africa
Norway
Portugal
Romania
Russia
-FP1
-091
-131
-271
-251
Spare part number
-061
-291
-B31
For use in country or region
Switzerland
Taiwan
Thailand
Turkey
Turkey-F
Ukraine
United Kingdom
United States
-141
-541
-BD1
-031
-001
Spare part number
-BG1
-AB1
-281
Component replacement procedures 77
