All manuals and user guides at all-guides.com
M-5
Quick Start Guide
Introduction
• Read this quick start guide carefully before installing and/or using this product.
• Keep this quick start guide for future reference and store it in a safe place.
Notice
.co
m
• This quick start guide may be revised or withdrawn at any time without prior notice.
• This quick start guide may not, in whole or in part, be copied, photocopied, reproduced, translated or converted to any
electronic or machine readable form without prior written consent of Opticon.
• Trademarks used are property of their respective owners.
• Under no circumstances shall Opticon be held responsible for any special, incidental, consequential or indirect
damages howsoever caused.
Precautions for Use
all
-g
uid
es
1. LED Safety
Do not stare into the LEDʼ s.
2. Handling Instructions
【M-5】
• Do not attempt to disassemble, modify or update this device.
• Do not use the scanner while operating machinery.
• Do not drop or put heavy items on this product or its cable.
• Do not pinch or forcibly bend the cable, especially at very low temperature.
• Do not insert foreign substances into the device.
• Do not use/leave this device:
- In areas exposed to direct sunlight for long periods of time
- In dusty environments
- In risk for an exposure to chemicals
- Near water or other liquids, as well as in extremely high humidity
- Near heat sources such as radiators, heat registers, stoves, or other types of devices that produce heat
- Near microwaves, medical devices, or RF-emitting devices
- In the reach of blinking lights such as CRT
• Do not use this product during a lightning storm.
【AC/DC Adapter】
• Use only the supplied AC adapter with the enclosed region specific plugs for connection to the wall socket.
• This product may produce heat when in use, but it does not affect its performance.
• Do not pull on the cord when unplugging the power cord from a power outlet. Grasp the plug to remove it.
• Do not plug in or out this product with wet hands.
• Unplug this product when it is not in use or when it is being cleaned.
Before Getting Started
■ What's in the Box
Confirm that you have the following items before getting started. Please note that the contents may differ
depending on interface specifications. Please contact the nearest dealer if items are damaged or missing.
No.
1 Scanner
Item
Function
An omnidirectional imaging scanner
Notes
−
−
−
−
−
−
−
−
−
−
−
Interface cable
A cable for connecting the scanner
3
Wedge branch cable
Y-cable: The cable that can be used to connect a keyboard
Only for Wedge interface.
and the scanner's straight cable to a host computer.
4
Connector cover
A cover used to fix the connection between the
Only for M-5-WEDGE+PS package.
Y-cable and the straight cable.
5
Instruction of connector cover An instruction manual for the connector cover
Only for M-5-WEDGE+PS package.
6
AC adapter
AC adapter with interchangeable plugs
Only for RS-232C and Wedge interface.
7
Interchangeable plugs
Plugs for different regions
Only for RS-232C and Wedge interface.
8
Quick start guide
This manual provides the basic product specification
and setup instructions.
2
Copyright © 2009, Opticon All rights reserved.
Different for each interface spec.
−
−
−
−
−
−
−
−
−
−
−
e
All manuals and user guides at all-guides.com
Overview
■ M-5 Basic Specifications
Parameter
Physical Size
Features Weight
Operation Scan Confirmation
Section
Keys
Interfaces RS-232C
USB
Wedge
Control ASIC
Section SDRAM
Flash ROM
Scanning Light Source
Section Wavelength
Scanning Method
Supported
Symbologies
(1D)
Supported
Symbologies
(2D)
Operating voltage
Power
Supply
Section
■ Detailed View
Specifications
Buzzer and 3 colors LED(Green/Blue/Orange)
9600bps 〜 115.2kbps
Full-Speed 12Mbps(HID/VCP)
Hi-Power Bus-powered
OEY-0603 CPU:ARM-1026EJ-S Core:160MHz
⑦
128Mbits(1M × 4Banks × 32Bits)
16Mbits(1M × 16Bits) Flash Memory
8-AllnGaP Red LEDs(Omniscan Mode)/625nm
4-AllnGaP red LEDs (Mobile Mode)/633nm
WVGA(752 x 480 pixels) CMOS area sensor
No.
Part
UPC-A,UPC-E, UPC-E1, UPC-A Add-on, UPC-E Add-on, EAN-13,
EAN-8, EAN-13 Add-on/EAN-8 Add-on, JAN-8 , JAN-13, Code
39,Tri-Optic, NW-7, Industrial 2 of 5, Interleaved 2 of 5, Code 93,
Code 128, GS1-128, S-Code, MSI/Plessey, UK/Plessey, TELEPEN,
Matrix 2 of 5, Chinese Post Matrix 2 of 5, IATA,Code 11,
Korean Postal Authority code , GS1 DataBar, Postal Code
①
Optical Window
−
−
−
−
−
−
−
−
−
−
−
②
Trigger Switch
The trigger switch is used for the manual
scanning operation. A single aiming guide
will be activated in this mode.
③
Mode Switch
The mode switch toggles between Mobile phone
scanning mode and Normal scanning mode.
④
Indicator LED
Green LED light shows the scanning
operation has been successful.
Blue LED light shows when the scanner is
ready to scan.
⑤
Indicator LED While Mobile Orange LED light shows when the scanner
phone scanning Mode
is ready for mobile code scanning.
⑥
Buzzer Holes
−
−
−
−
−
−
−
−
−
−
−
⑦
Screw Holes
Used to mount the scanner onto a base plate,
wall etc. using D4 (diameter: 4mm) screws.
PDF417,MicroPDF417, QR Code,MicroQR Code,Data
Matrix (ECC 000-140/ECC 200),MaxiCode (Modes 2 to 5),
Aztec Code, EAN.UCC Composite bar code, Codablock F
4.5 to 6.6V
RS-232C, Wedge
140mA (typ) 130mA (typ)
0 to 40 deg. C
− 40 to 70 deg. C
5 to 95 ％ (non-condensing)
5 to 95 ％ (non-condensing)
Fluorescent：10,000lx or less
Incandescent lamp：10,000lx or less
Sunlight：50,000lx or less (*1)
Dust-and-Drip Proof IP52
Static Electricity 15kV (no destruction)
Dropped once from each of 5 angles onto
Shock
concrete floor from a height of 150cm with
Endurance
no defects found. (Total 5 times)
(*1)Except “Mobile phone scanning mode” in each condition. Please note that scanning while the
LCD screen is exposed to direct sunlight may have a negative effect on the reading performance.
■ Basic Specifications for Universal AC adapter
Parameter
Function
■ Various Scanning Modes
The following modes are available for different uses:
□ Normal scanning mode
A mode in which the scanner is configured optimally for general barcode
reading. The device automatically starts scanning when a label is
held in front of it. The trigger key activates the single line scanning.
□ Mobile phone scanning mode
A special mode ― in which the lighting conditions are optimized for
reading barcodes,― displayed on mobile devices such as a phone.
The device automatically starts scanning when a label is held in front
of it. The trigger key activates the single line scanning.
□ Single line scanning
While the trigger switch is pressed, the illumination LEDs turn on
and only one code can be read. The single line can read one target
code out of multiple printed codes in this mode.
Specifications
Size
(H)75 x (W)47.5 x (D)28mm (excluding boss)
Cable Length
1.8m
Colour
Black
Power
ON
Mode Switch
Finished Scanning
or Time-Out
Power Voltage 5.7V to 6.3V
Maximum Current
2A Max
Environmental Operating Temp. 0 to 40 deg. C
Specification
Operating Humidity 25 to 85% (non-condensing)
Trigger
Switch
Mobile phone
scanning mode
Storage Temp. − 20 to 60 deg. C
Storage Humidity
20 to 90% (non-condensing)
Trigger
Switch
Normal scanning
mode
Power Voltage AC 90V to 265V
Supply Current 500mA Max
Output
③
PS/2 Keyboard (Connect or disconnect the keyboard.)
Stand-by
Input
②
①
400mA
(when scanning and decoding) 420mA
Current
consumption Average
(typ) 210mA (typ)
(when scanning and decoding) 280mA
Physical
Features
⑥
2 keys (Trigger Switch/Mode Switch)
USB
Ambient
Light
Immunity
④
Approx.295g (excluding the cable)
Peak
Durability Operating Temp.
Storage Temp.
Operating Humidity
Storage Humidity
⑤
(H)140.0 × (W)92.0 × (D) 95.5 mm
Figure 1. Scanning mode diagram
Single line
scanning
Finished Scanning
or Time-Out
All manuals and user guides at all-guides.com
Setting Menu Codes
The M-5 can be configured by reading the menu codes below. Read more about configuration options
(by Opticonfigure) on www.opticon.com.
: Default
Default Setting
■ Enable QR Code
(* Use this only when “Disable QR Code” is set in advance.)
Start / END: ZZ
Read Time Setting
You can set the time that the scanner will try to read a code
after it is detected by the auto trigger. This can be set for “Normal scanning mode” and “Mobile phone scanning mode” .
For single line scanning, it can be set as the LED aiming time.
■ Normal scanning mode
Serial command : Y0 (0.5s)
Serial command : Y2 (2.0s)
Serial command : Y1 (1.0s)
Serial command : Y3 (3.0s)
Enable QR Code: BCD
Stop / END: ZZ
■ Back to default
Serial command : U2, C01, SU, UB
■ Mobile phone scanning mode
Scanning Mode Setting
"Normal scanning mode" or "Mobile phone scanning mode"
can be selected as primary mode when the scanner starts up.
Serial command : E91 (1s)
Serial command : E93 (3s)
Serial command : E92 (2s)
Serial command : E94 (4s)
■ Normal scanning mode
Serial command : E8Y
■ Single line scanning
Serial command : E8V (1s)
■ Mobile phone scanning mode
Serial command : E8Z
Serial command : E8W (3s)
Serial command : E8X (5s)
All manuals and user guides at all-guides.com
Setting Menu Codes
s
lt
e
r”.
e.
Multiple read reset time Setting
Auto Trigger Setting
The time that a code will not be read after it is read successful
once can be set. This can prevent the double read of a code.
Auto trigger ON / OFF can be set. When it is set to OFF, only
the trigger switch can be used to activate the scanner.
■ Multiple read reset time
■ Auto Trigger ON
Serial command : +I
Serial command : AJ (200ms)
Serial command : E9H (700ms)
Serial command : AK (300ms) Serial command : E9I (800ms)
Serial command : AL (400ms)
■ Auto Trigger OFF
Serial command : +F
Serial command : E9J (900ms)
Serial command : AM (500ms) Serial command : E8T (1s)
Serial command : AN (600ms)
Serial command : AG (Infinity)
Contact
Please contact OPTICON or your local dealer.
The Netherlands
U.S.A.
France
Germany
Italy
Spain
Opticon Sensors Europe B.V.
tel: +31 (0)23-5692700 / email: [email protected]
Opticon Inc.
tel: 800-636-0090 / email: [email protected]
Opticon S.A.S.
tel: +33 (0)1-41461260 / email: [email protected]
Opticon Sensoren GmbH
tel: +49 (0)6074-91890-0 / email: [email protected]
Opticon s.r.l.
tel: +39 (0)051-6321800 / email: [email protected]
Opticon Sensores S.L.
tel: +34 (0)902-747469 / email: [email protected]
Sweden
United Kingdom
Taiwan
China
Australia
Brazil
Opticon Sensors Nordic AB
tel: +46 (0)8-58548560 / email: [email protected]
Opticon Limited
tel: +44 (0)1582-635100 / email: [email protected]
Opticon Far Eastern Ltd.
tel: +886 2-27597444 / email: [email protected]
Opticon Sensors Europe B.V., Shanghai Representative Office
tel: +86 21-64480881 / email: [email protected]
Opticon Sensors Pty. Ltd.
tel: +61 (0)2-43402666 / email: [email protected]
Opticon Sensors Europe B.V., Latin American Office
tel: +55 11-5081 2088 / email: [email protected]
More product details, additional support, and configuration options (from the Universal Menu Book) are available at www.opticon.com.
M-500009062-0-00
">
