Opticon OPR 2001 Specification Manual
Opticon OPR 2001 is a handheld laser barcode scanner featuring high-speed scanning, error-free data capture, and versatile connectivity options. With its compact and ergonomic design, it's ideal for retail, healthcare, and logistics applications. Its laser scan technology ensures accurate and reliable scanning of various barcodes, and its adjustable scan angle allows for flexible use.
Advertisement
Advertisement
Laser Barcode Scanner
OPR 2001
The OPR 2001 is a handheld laser barcode scanner.
Specifications Manual
Opticon
OPR 2001
Specifications Manual
All information subject to change without notice.
Document History
Model Number:
Edition:
Date:
OPR 2001
1A
2007-02-14
Specification Number:
Original Spec Number:
SS07011
SS06121
Copyright 2007 Opticon. All rights reserved.
This manual may not, in whole or in part, be copied, photocopied, reproduced, translated or converted to any electronic or machine readable form without prior written consent of Opticon.
Limited Warranty and Disclaimers
PLEASE READ THIS MANUAL CAREFULLY BEFORE INSTALLING OR USING THE
PRODUCT.
Serial Number
A serial number appears on all Opticon products. This official registration number is directly related to the device purchased. Do not remove the serial number from your Opticon device. Removing the serial number voids the warranty.
Warranty
Unless otherwise agreed in a written contract, all Opticon products are warranted against defects in materials and workmanship for two years after purchase. Opticon will repair or, at its option, replace products that are defective in materials or workmanship with proper use during the warranty period. Opticon is not liable for damages caused by modifications made by a customer. In such cases, standard repair charges will apply. If a product is returned under warranty and no defect is found, standard repair charges will apply. Opticon assumes no liability for any direct, indirect, consequential or incidental damages arising out of use or inability to use both the hardware and software, even if Opticon has been informed about the possibility of such damages.
Packaging
The packing materials are recyclable. We recommend that you save all packing material to use should you need to transport your scanner or send it for service. Damage caused by improper packaging during shipment is not covered by the warranty.
Trademarks
Trademarks used are the property of their respective owners.
Opticon Inc. and Opticon Sensors Europe B.V. are wholly owned subsidiaries of OPTOELECTRONICS Co., Ltd., 12-17,
Tsukagoshi 4-chome, Warabi-shi, Saitama, Japan 335-0002. TEL +81-(0) 48-446-1183; FAX +81-(0) 48-446-1184
SUPPORT
USA Europe
Phone: 800-636-0090
Email: [email protected]
Web: www.opticonusa.com
Email: [email protected]
Web: www.opticon.com
2
Opticon
OPR 2001
Specifications Manual
Contents
1.
Abstract ....................................................................................................................................... 7
2.
Overview...................................................................................................................................... 7
3.
Physical Features ....................................................................................................................... 8
3.1.
Dimensions ......................................................................................................................... 8
3.2.
Weight ................................................................................................................................. 8
4.
Environmental Specifications ................................................................................................... 8
4.1.
Operating Temperature and Humidity................................................................................. 8
4.2.
Storage Temperature and Humidity .................................................................................... 8
4.3.
Ambient Light Immunity....................................................................................................... 9
5.
Electrical Specifications .......................................................................................................... 10
5.1.
Electrical Characteristics: RS-232C .................................................................................. 10
5.2.
Electrical Characteristics: USB, Wedge ............................................................................ 10
6.
Optical Specifications .............................................................................................................. 11
6.1.
Laser Scan Specifications................................................................................................. 11
6.1.1.
Tilt of Laser Scan Line .............................................................................................................11
6.1.2.
Curvature of Scan ....................................................................................................................11
7.
Technical Specifications.......................................................................................................... 12
7.1.
Print Contrast Signal (PCS) .............................................................................................. 12
7.2.
Minimum Resolution.......................................................................................................... 12
7.3.
Scan Area and Resolution ................................................................................................ 13
7.3.1.
Depth of Field...........................................................................................................................13
7.4.
Pitch, Skew, and Tilt.......................................................................................................... 14
7.4.1.
Pitch Angle...............................................................................................................................14
7.4.2.
Skew Angle and Dead Zone ....................................................................................................15
7.4.3.
Tilt Angle ..................................................................................................................................16
7.5.
Curvature .......................................................................................................................... 17
8.
Interface Specifications ........................................................................................................... 17
8.1.
RS-232C Interface ............................................................................................................ 17
8.1.1.
Settings and Communication ...................................................................................................17
8.1.2.
Signal Level..............................................................................................................................18
8.1.3.
Pin Assignment ........................................................................................................................18
8.1.4.
Interface Circuit........................................................................................................................19
3
Opticon
OPR 2001
Specifications Manual
8.1.5.
Character Format.....................................................................................................................19
8.1.6.
Character Format.....................................................................................................................19
8.1.7.
Communication Format............................................................................................................19
8.1.8.
Handshaking ............................................................................................................................20
8.2.
USB-HID and USB-VCP Interface Specifications ............................................................. 25
8.2.1.
Settings ....................................................................................................................................25
8.2.2.
Interface Circuit........................................................................................................................25
8.3.
DOS/V Wedge Interface Specification .............................................................................. 25
9.
Cable and Connector ............................................................................................................... 26
9.1.
RS-232C Cable ................................................................................................................. 26
9.2.
USB Cable ........................................................................................................................ 26
9.2.1.
Connector.................................................................................................................................27
9.2.2.
Pin Assignment ........................................................................................................................27
9.3.
Wedge Cable .................................................................................................................... 27
9.3.1.
Connectors...............................................................................................................................28
9.4.
Connector Specification (Scanner Side) ........................................................................... 29
10.
Default Settings ........................................................................................................................ 29
10.1.
Set Default Interface ......................................................................................................... 29
10.2.
Default Settings 1: Readable Codes ................................................................................. 31
10.3.
Default Settings 2: Read Options, Trigger, Buzzer ........................................................... 32
11.
Serial Number ........................................................................................................................... 33
12.
Packaging Specifications ........................................................................................................ 33
12.1.
Individual Packaging Specification.................................................................................... 33
12.2.
Collective Packaging......................................................................................................... 33
13.
Durability ................................................................................................................................... 34
13.1.
Electrical Noise ................................................................................................................. 34
13.2.
Static Electricity................................................................................................................. 34
13.3.
Shock ................................................................................................................................ 35
13.3.1.
Drop Test (without packaging).................................................................................................35
13.3.2.
Drop Test (with individual packaging)......................................................................................35
13.4.
Vibration Strength ............................................................................................................. 35
13.5.
Dust and Drip Proof........................................................................................................... 35
13.5.1.
Cable Strength .........................................................................................................................36
13.5.2.
Cable Tail Bending Test...........................................................................................................36
4
Opticon
OPR 2001
Specifications Manual
14.
Reliability................................................................................................................................... 36
15.
Trigger and Read Options ....................................................................................................... 37
15.1.
Trigger Modes ................................................................................................................... 37
15.2.
Read Modes...................................................................................................................... 37
15.3.
Auto Trigger Options ......................................................................................................... 38
15.3.1.
Auto Trigger Sensor.................................................................................................................38
16.
Trigger and Read Settings ....................................................................................................... 40
16.1.1.
Enable/Disable Settings...........................................................................................................40
16.2.
Auto Trigger Stand Detection Settings.............................................................................. 40
16.2.1.
Stand Only ...............................................................................................................................40
16.2.2.
Always......................................................................................................................................41
16.2.3.
Manually...................................................................................................................................41
17.
Regulatory Compliance ........................................................................................................... 42
17.1.
Laser Safety ...................................................................................................................... 42
17.2.
Product Safety................................................................................................................... 42
17.3.
EMC .................................................................................................................................. 42
17.4.
RoHS................................................................................................................................. 42
18.
Safety......................................................................................................................................... 43
18.1.
Shock ................................................................................................................................ 43
18.2.
Temperature Conditions.................................................................................................... 43
18.3.
Foreign Materials .............................................................................................................. 43
18.4.
Other ................................................................................................................................. 43
19.
Mechanical Drawing ................................................................................................................. 44
Table of Figures
Figure 1: Ambient light immunity .................................................................................................. 9
Figure 2: Laser scanning tilt and curvature ................................................................................ 12
Figure 3: Depth of field ............................................................................................................... 13
Figure 4: Pitch ............................................................................................................................ 14
Figure 5: Skew angle and dead zone ......................................................................................... 15
Figure 6: Tilt angle ...................................................................................................................... 16
Figure 7: Curvature..................................................................................................................... 17
Figure 8: Interface circuit ............................................................................................................ 19
Figure 9:Character format (same for both sending and receiving) ............................................. 19
Figure 10: Communication format .............................................................................................. 19
Figure 11: No handshaking......................................................................................................... 20
Figure 12: Busy/Ready communication...................................................................................... 21
5
Opticon
OPR 2001
Specifications Manual
Figure 13: Cannot receive command ......................................................................................... 21
Figure 14: Signal timing.............................................................................................................. 22
Figure 15: ACK/NAK................................................................................................................... 23
Figure 16: ACK/NAK—No response........................................................................................... 24
Figure 17: Interface circuit .......................................................................................................... 25
Figure 18: RS-232C cable .......................................................................................................... 26
Figure 19: USB cable ................................................................................................................. 26
Figure 20: USB "A" connector .................................................................................................... 27
Figure 21: Wedge cable.............................................................................................................. 27
Figure 22: DOS/V host connector............................................................................................... 28
Figure 23: DOS/V keyboard connector....................................................................................... 28
Figure 24: Serial number diagram .............................................................................................. 33
Figure 25: Drop test.................................................................................................................... 35
Figure 26: Cable tail bending test............................................................................................... 36
Figure 27: Auto trigger operation ................................................................................................ 38
Figure 28: Trigger options........................................................................................................... 39
Figure 29: Mechanical drawing................................................................................................... 44
6
Opticon
OPR 2001
Specifications Manual
1. Abstract
This manual provides specifications for the OPR 2001 laser barcode scanner.
2. Overview
The OPR 2001 is a handheld laser barcode scanner. The use of a short-wavelength red laser beam enhances visibility when scanning lines.
The OPR 2001 can be configured to scan both positive and negative barcodes. Scanned data is transferred via an RS-232C, USB, or Wedge interface. Auto-trigger settings are available.
The OPR 2001 complies with RoHS.
Supported symbologies:
Linear (1D) Postal
JAN/UPC/EAN, incl. add-on Chinese Post
Codabar/NW-7 Korean Postal Authority Code
Code 11
Code 39
Code 93
Code 128
GS1-128 (EAN-128)
GS1 Databar (RSS)
IATA
Industrial 2of5
Interleaved 2of5
ISBN-ISMN-ISSN
Matrix 2of5
MSI/Plessey
S-Code
Telepen
Tri-Optic
UK/Plessey
2D
Composite Codes
MicroPDF417
PDF417
7
3.1. Dimensions
W 151.0 x D 56.0 x H 30.5 mm
3.2. Weight
60 grams max. (excluding cable weight)
4.1. Operating Temperature and Humidity
Temperature: -5° to +50° C
Humidity: 20 to 85% RH
4.2. Storage Temperature and Humidity
Temperature: -20° to +60° C
Humidity: 10 to 90% RH
Opticon
OPR 2001
Specifications Manual
8
Opticon
OPR 2001
Specifications Manual
4.3. Ambient Light Immunity
Decoding performance is guaranteed when the range of illumination on a barcode surface is between zero and the following values:
Incandescent light
Fluorescent light
3,000 lx
3,000 lx
Figure 1: Ambient light immunity
Conditions
Barcode Sample: OPTOELECTRONICS Test Sample
PCS: 0.9
Symbology:
Quiet Zone:
N/W Ratio:
9-digit Code 39
10 mm
1:2.5
Angle:
Curvature:
α = 0° β = 15° γ = 0°
Ｒ = ∞
Power Supply Voltage: 5.0 V
Direct light or specular reflection light from a source should be prevented from entering the acceptance area.
Note:
α, β and γ respectively represent pitch, skew and tilt. Please see section 7 for how these values are defined.
9
Opticon
OPR 2001
Specifications Manual
5.1. Electrical Characteristics: RS-232C
Power supply voltage
Operating current
Peak current
Standby current
Startup time
V
DD
4.5 6.0 6.5 V
I
OP
I
PEAK
— 550 600 mA
I
PRE
— 35 70 mA
T
D
— 100 — ms
5.2. Electrical Characteristics: USB, Wedge
Power supply voltage
Operating current
Peak current
Standby current
Startup time
Conditions
V
DD
4.5 5.0 5.5 V
I
OP
I
PEAK
— 450 500 mA
I
PRE
— 35 70 mA
T
D
— 100 — ms by the voltage between both ends of resistance.
• Power supply voltage is measured at a connector terminal area.
• The current value depends on the interface type and host computer to which the device is connected.
10
Opticon
OPR 2001
Specifications Manual
6.1. Laser Scan Specifications
Light-emitting element
Emission wavelength
Light output
Scanning method
Scanning speed
Scan angle
Red laser diode
650 ±10 (25° C)
1.0 or less
Bi-directional scanning
100 ±20
Scan angle: 54 ±5
— nm mW
— scans/s
°
Read angle: 44 (Min) °
Notes:
Refer to chapter 15, “Trigger and Read Options,” to read about the scan modes.
Refer to chapter 7, “Technical Specifications,” to read about scanning performance.
6.1.1.
Tilt of Laser Scan Line
Scanning tilt is the vertical difference between the ends of a laser scan line.
• Up to 0.92° in a vertical direction from the scan origin (mirror motor mirror).
• Up to 2.46 mm when measured at 150 mm from the scan origin.
Measurement is done at the center of the laser scan line.
6.1.2.
Curvature of Scan
Scanning curvature is the maximum difference between the laser scan line and the line between the ends of the laser scan line.
• Up to 1.17° in a vertical direction from the scan origin (mirror motor mirror).
• Up to 3.06 mm when measured at 150 mm from the scan origin.
11
Measurement is done from the center of the laser scan line.
Opticon
OPR 2001
Specifications Manual
Figure 2: Laser scanning tilt and curvature
The conditions for technical specifications are as follows, unless otherwise specified in each section.
Conditions
Ambient temperature and humidity:
Ambient light:
Background:
Power supply voltage:
Decoding test:
Room temperature (5 to 35º C)
Room humidity (45% to 85% RH)
500 to 900 lx
Barcode = black
Space = white
Margin = white
Background of label = black
6.0 V (RS-232C) / 5.0 V (USB, Wedge)
Approve the performance when decoding is successful in all ten tests.
(Decoding is deemed successful when completed in 0.5 seconds or less.)
7.1. Print Contrast Signal (PCS)
0.45 or higher (over 70% of reflectivity of space and quiet zone).
PCS=
Reflectance of white bar
－Reflectance of black bar
Reflectance of white bar
Scanning performance may decline if dirt or scratches mar the optical window. Keep the optical window clean.
7.2. Minimum Resolution
0.127 mm
12
Opticon
OPR 2001
Specifications Manual
7.3. Scan Area and Resolution
7.3.1.
Depth of Field
The depth of field is measured from the edge of the scanner. The scanning range is within the circular arc centered on the scan origin.
Figure 3: Depth of field
Symbology Resolution Decode Depth (mm) PCS
Code 39
Code 39
Code 39
Code 39
Code 39
1.0 mm
0.5 mm
0.25 mm
0.15 mm
0.127 mm
40–500
20–350
20–200
20–100
30–70
0.9
0.9
0.9
0.9
0.9
Conditions
Barcode Sample: OPTOELECTRONICS Test Sample
N/W Ratio:
Angle:
1:2.5
α = 0°, β = 15°, γ = 0°
13
Resolution Symbology PCS Quiet Digits
1.0 mm
0.5 mm
0.25 mm
0.15 mm
0.127 mm
Code 39
Code 39
Code 39
Code 39
Code 39
0.9
0.9
0.9
0.9
0.9
25 mm
18 mm
10 mm
7 mm
5 mm
1
3
8
10
4
7.4. Pitch, Skew, and Tilt
7.4.1.
Pitch Angle
Scanning performance is guaranteed when α = ±35°
Opticon
OPR 2001
Specifications Manual
Figure 4: Pitch
14
7.4.2.
Opticon
OPR 2001
Specifications Manual
Skew Angle and Dead Zone
Scanning performance is guaranteed when skew angle: β ≤ ±50° (Excluding dead zone)
Dead zone: β = ±8° (There are some areas in which decoding fails due to specular reflection)
Figure 5: Skew angle and dead zone
15
7.4.3.
Tilt Angle
Scanning performance is guaranteed when γ ≤ ±20°
Opticon
OPR 2001
Specifications Manual
Figure 6: Tilt angle
Conditions
Barcode Sample: OPTOELECTRONICS Test Sample
Distance:
Label:
70 mm from the front edge of the scanner
Angles:
Pitch, Skew Angle, Dead Zone
PCS = 0.9, Resolution = 0.25 mm, Symbology = 9-digit Code 39,
Quiet Zone = 10 mm, N/W Ratio = 1:2.5
Tilt Angle
PCS = 0.9, Resolution = 0.26 mm, Symbology = 13-digit JAN, Quiet Zone = 10 mm
Pitch angle:
Skew angle: β = +15°, Tilt angle: γ = 0°
Tilt angle:
Pitch angle: α = 0°, Skew angle: β = +15°
Skew angle, Dead zone
: Pitch angle: α = 0°, Tilt angle: γ = 0°
16
Opticon
OPR 2001
Specifications Manual
7.5. Curvature
With 8-digit JAN/UPC/EAN barcodes, decoding performance is guaranteed when
R = 15 mm.
With 13-digit JAN/UPC/EAN barcodes, decoding performance is guaranteed when
R = 20 mm.
Figure 7: Curvature
Conditions
Barcode Sample: OPTOELECTRONICS Test Sample
PCS = 0.9, Resolution = 0.26 mm, Quiet Zone = 10 mm
Distance: 70 mm from the front edge of the scanner
8.1. RS-232C Interface
8.1.1.
Settings and Communication
Reading the menu barcodes in section 10.1 can set the RS-232C interface default.
Baud rate
Start/stop bits
Data bits
Parity bits
9600 bps
1 bit
8 bits
No parity
Flow control time out Indefinitely
You can change the communication condition using the menu barcode.
17
8.1.2.
Signal Level
Signal Name I/O RS-232C Level (V)
TxD
RxD
RTS
CTS
OUT
IN
OUT
IN
-5 to -15
-3 to -15
-5 to -15
-3 to -15
+5 to +15
+3 to +15
+5 to +15
+3 to +15
8.1.3.
Pin Assignment
Signal Pin Notes
NC
TXD
RXD
---
GND
---
CTS
RTS
NC
FG
7
8
5
6
3
4
1
2
Open (not connected)
Connected to pin 6 with jumper cable.
Connected to pin 4 with jumper cable.
9
Open (not connected)
SHELL
Shield
Connector: D-sub, 9-pin, Female
Power supply: DC jack, EIAJ voltage Class 2
Opticon
OPR 2001
Specifications Manual
18
8.1.4.
Interface Circuit
Opticon
OPR 2001
Specifications Manual
Figure 8: Interface circuit
8.1.5.
Character Format
Uses the same format for both sending and receiving.
8.1.6.
Character Format
Figure 9:Character format (same for both sending and receiving)
8.1.7.
Communication Format
Figure 10: Communication format
19
8.1.8.
Opticon
OPR 2001
Specifications Manual
Handshaking
Select handshaking options using the menu or command listed below.
Handshaking Menu/Command
No handshake P0
BUSY/READY P1
MODEM P2
ACK/NAK P3
ACK/NAK NO RESPONSE P4
The scanner attempts the communication regardless of the state of the host computer.
Figure 11: No handshaking
20
Opticon
OPR 2001
Specifications Manual
b) BUSY/READY
The scanner and the host computer notify each other of their state and whether they can receive data with BUSY/READY through an RTS line. They can communicate state to each other through a CTS line when
connected as in the following figure.
Figure 12: Busy/Ready communication
The scanner stays ON (is able to receive data) except during certain parts of the process, such as receiving data (buzzer command execution), transmitting data, and menu processing. The scanner checks the CTS line before transmitting data. When it is ON, the scanner transmits data. When it is OFF, the scanner waits for it to turn ON within a set time. The scanner will abort transmission with an error indication (buzzer) when the CTS line is not ON within a specified period. The Flow Control time-outs are as follows, and the default setting is “indefinitely“ (I0).
Flow Control Time Out Menu/Command
Indefinitely I0
100 ms
200 ms
400 ms
I1
I2
I3
Figure 13: Cannot receive command
21
Opticon
OPR 2001
Specifications Manual
CTS, TXD signal timing
When the CTS line (RTS signal of the host) is turned OFF while sending a TxD signal, the scanner transmits one character and waits. When the CTS signal is turned ON while transmitting a character, the character will be transmitted.
Figure 14: Signal timing
Note:
When using loopback (wire connection) for RTS, CTS line of the scanner in this setting, No handshake is not enabled.
c) ACK/NAK
After data has been transmitted, the scanner expects to receive one of the following responses from the host:
ACK
response—Action: The scanner completes transmission with the goodread buzzer and returns to the initial state.
NAK
response—Action: The scanner sends the data again and waits for the response from the host.
DC1
response—Action: The scanner returns to waiting for the trigger, if it has a trigger (the initial state).
None
response—Action: The scanner sounds the error buzzer and returns to the initial state.
ACK/NAK timeout can be set as follows using the menu or commands.
ACK/NAK timeout Menu / Command
Indefinitely (default) XI4
100 ms
500 ms
1000 ms
XI5
XI6
XI7
22
Opticon
OPR 2001
Specifications Manual
Figure 15: ACK/NAK
23
Opticon
OPR 2001
Specifications Manual
d) ACK/NAK NO RESPONSE
When no response from the host is received within the setting time, the scanner assumes an ACK response, and returns to the initial state without the error buzzer. The other actions are the same as ACK/NAK.
Figure 16: ACK/NAK—No response
24
Opticon
OPR 2001
Specifications Manual
8.2. USB-HID and USB-VCP Interface Specifications
There are two models that use a USB interface: HID (Human Interface Device Class) and
COM (Communication Device Class). The USB-COM model is referred to as USB-VCP because a VCP (Virtual Communication Port) allows virtual serial communication and the commands can be transmitted from the host computer.
8.2.1.
Settings
Reading the menu barcodes in section 10.1 can set the USB interface default.
The interface is full-speed USB (12 Mbps).
Device Class: High power bus-powered function. This interface does not require an AC adaptor. It connects to a high-power bus (500 mA max.) USB terminal.
Japanese Kanji data or images cannot be transmitted via the USB-HID interface.
Note:
You must install the USB-VCP driver on the host.
8.2.2.
Interface Circuit
Figure 17: Interface circuit
Do not use the keyboard while the scanner is transmitting the data to the host.
Doing so may cause failure in data transactions.
8.3. DOS/V Wedge Interface Specification
Reading the menu barcodes in section 10.1 can set the DOS/V Wedge interface default.
For either interface (USB or HID/Wedge)—Set the language for the scanner and PC keyboard to the same language before use; otherwise, the output may not be correct.
25
9. Cable and Connector
9.1. RS-232C Cable
(Standard specification)
Figure 18: RS-232C cable
Type: Straight
Diameter: Φ4.8 ±0.5 mm
Length:
Cores:
1500 +50, -0 mm
6 insulated wires, 1 conductive wire
9.2. USB Cable
(Standard specification)
Figure 19: USB cable
Type: Straight
Diameter: Φ4.8 ±0.5 mm
Length: 1500 +50, -0 mm
Cores: 4 insulated wires, 1 conductive wire
26
Opticon
OPR 2001
Specifications Manual
9.2.1.
Connector
a) USB "A" connector
#1
#4
Figure 20: USB "A" connector
9.2.2.
Pin Assignment
Pin Signal
1 VCC
2 -DATA
3 +DATA
4 GND
9.3. Wedge Cable
(Standard specification)
3
4
1
2
Opticon
OPR 2001
Specifications Manual
Figure 21: Wedge cable
Type:
Diameter:
Length:
Cores:
Y cable
Φ4.8 ±0.5 mm
1500 +50, -0 mm
6 insulated wires, 1 conductive wire
27
Opticon
OPR 2001
Specifications Manual
9.3.1.
Connectors
Figure 22: DOS/V host connector
6
4
5
3
2
1
Contact Number Signal Name
1 CPU_DATA
2 NC
3 GND
4 VCC
5 CPU_CLK
6 NC
b) DOS/V Keyboard Connector
5
3
6
4
Figure 23: DOS/V keyboard connector
1
2
Contact Number Signal Name
1 KEY_DATA
2 NC
3 GND
4 VCC
5 KEY_CLK
6 NC
Do not use the keyboard while the scanner is transmitting the data to the host.
Doing so may cause failure in data transactions.
28
9.4. Connector Specification (Scanner Side)
CN1 (12-pin)
Pin No RS-232C USB Wedge
1 GND GND GND
2 RXD — —
3 TXD — —
4 CTS — —
5 RTS — —
6 NC — —
KEY_CLK
KEY_DATA
11 VCC VCC VCC
12 FG (shield) FG (shield) FG (shield)
10. Default Settings
10.1. Set Default Interface
Scan the following menu barcodes to return to the default settings.
RS-232C
Functions
SET
RS-232C
END
Menu labels
_ZZ_
_U2_
_ZZ_
Menu codes
ZZ
U2
ZZ
Opticon
OPR 2001
Specifications Manual
29
USB-HID
Functions
SET
USB-HID
END
Menu labels
_ZZ_
_SU_
_ZZ_
Menu codes
ZZ
SU
ZZ
USB-VCP
Functions
SET
USB-VCP
END
Menu labels
_ZZ_
C01
_ZZ_
Menu codes
ZZ
C01
ZZ
Wedge (with external keyboard)
Functions
SET
AT-Wedge
Keyboard layout: with keyboard
END
Menu labels
_ZZ_
_UB_
_KM_
_ZZ_
Menu codes
ZZ
UB
KM
ZZ
Wedge (without external keyboard)
Functions
SET
AT-Wedge
Keyboard layout: without keyboard
END
Menu labels
_ZZ_
_UB_
_KL_
_ZZ_
Menu codes
ZZ
UB
KL
ZZ
30
Opticon
OPR 2001
Specifications Manual
Opticon
OPR 2001
Specifications Manual
UPC-A
UPC-A Add-on
UPC-E
UPC-E Add-on
EAN-13
EAN-13 Add-on
EAN-8
EAN-8 Add-on
Chinese Post Matrix
2of5
Codabar / NW-7
Code 11
Code 39
Code 93
Code 128
GS1-128 (EAN/UCC-
128)
GS1 DataBar (RSS)
(all, incl. CC-A/B);
Limited/ Expanded
IATA
Industrial2of5
Interleaved2of5
Korean Postal Code
(Code 3of5)
10.2. Default Settings 1: Readable Codes
Code
Length
CD
X
X
X
X
X
X
X
X
X
X
X
X
X X
Calculate
CD
X
X
X
X
X
X X
X X
X X
X X X
Set
Prefix
Set
Suffix
Other
— CR
— CR
— CR
— CR
— CR
— CR
— CR
— CR
X —
—
—
CR
— CR
CR
Not transmit ST/SP
Not transmit ST/SP
— CR
— CR
— CR
X X — CR
X
X
X
X —
X —
X —
X X X — CR
X —
MSI/Plessey
S-Code
Telepen
Trioptic
UK/Plessey
X CD1 CD1 —
X X —
X X — CR
X
X
—
—
— CR Not transmit ST/SP
— CR
31
Opticon
OPR 2001
Specifications Manual
Notes:
In the “Reading” column, “
” means “Enable reading” and “X” means “Disable reading.”
In the “Transmit code length” column, “
” means “Transmit code length” and “X” means
“Do not transmit code length.”
In the “Transmit CD” column, “
” means “Transmit check digit” and “X” means “Do not transmit check digit.”
In the “Calculate CD” column, “
” means “Calculate check digit” and “X” means “Do not calculate check digit.”
“— “ means “not supported.”
In the “Prefix” column, “—“ means “there is no prefix setting.”
10.3. Default Settings 2: Read Options, Trigger, Buzzer
Setting the number of characters
Read mode
Multiple read reset time
Add-on wait mode
Multiple column read
Redundancy Default option
([X0] setting)
Other options
([X1 .. X3] setting)
([BS .. BW] setting)
Trigger switch
Trigger repeat
Auto trigger
Read time
Margin check
Buzzer duration
Buzzer tone
Buzzer loudness
Buzzer transmission
Startup buzzer
Good read LED
Fixed length OFF all codes
Single read
500 ms
500 ms
Disable
Read 1 times, redundancy = 0
Read n times, redundancy = n+1 for the following symbologies and lengths:
● Code 11 with length <= 5
● Code 39 with length <= 5
● IATA,Industrial 2of5, Interleaved 2of5 with length <= 8
● Matrix 2of5 (& Chinese Post), Scode with length <= 8
● MSI/Plessey with length <= 4
● NW-7 (Codabar) with all lengths
Enable
Disable
Disable
2 seconds (when trigger enabled)
Normal
50 ms
Single tone (3 kHz)
Maximum
Before transmission
Enable
Indicator duration 200 ms
32
11. Serial Number
The serial number shown below is affixed to the scanner.
Opticon
OPR 2001
Specifications Manual
Figure 24: Serial number diagram
12. Packaging Specifications
12.1. Individual Packaging Specification
Put the scanner in a protective foam bag and place it in a single packing box.
Size of the package (after assembly: 245 (W) x 110 (D) x 40 (H) mm
12.2. Collective Packaging
Put 50 individually packaged OPR 2001 scanners in a collective packaging box.
Dimensions: 650 mm (W) x 550 mm (D) x 250 mm (H)
Note:
The “RO” mark labeled on the package tray or package box guarantees that the applicable product has passed our test of RoHS restrictions compliance (the restriction of the use of certain hazardous substances in electrical and electronic equipment, 2002/95
EC). However, this document does not have any legal weight in the European Union.
33
Opticon
OPR 2001
Specifications Manual
13. Durability
13.1. Electrical Noise
No malfunction occurred when sinusoidal electrical noise (10 Hz–100 kHz, < 0.1 Vp-p) was added to the power supply line.
Conditions
Barcode Sample: OPTOELECTRONICS Test Sample
PCS: 0.9
Quiet Zone:
N/W Ratio:
Angle:
10 mm
1:2.5
α = 0° β = 15° γ = 0°
Power Supply Voltage: 5.0 V
13.2. Static Electricity
Air discharge:
Measurement environment:
±10 kV max. (No malfunction)
±15 kV max. (No destruction)
Use electrostatic testing device compliant with IEC 61000-4-2
Built up and discharged 15 kV of static electricity on the scanner surface 50 times.
Discharge resistance: 330 Ω
Capacitor charging: 150 pF
34
Opticon
OPR 2001
Specifications Manual
13.3. Shock
13.3.1.
Drop Test (without packaging)
No malfunction occurred after the following drop test.
Drop Test: Drop the scanner from a height of 150 cm onto a concrete floor three times on each of 5 sides.
Figure 25: Drop test
13.3.2.
Drop Test (with individual packaging)
No malfunction occurred after the following drop test.
Drop Test: Drop the scanner from a height of 150 cm onto a concrete floor on each of one corner, three edges, and six sides (10 drop tests in total)..
13.4. Vibration Strength
No malfunction occurred after the following vibration test.
Vibration test: Increase the frequency of the vibration from 12 Hz to 100 Hz with accelerated velocity 19.6 m/s
2
(2 G) for 60 minutes in non-operating state. Repeat this routine in each X, Y, Z direction once for 60 minutes each.
13.5. Dust and Drip Proof
IEC IP42
Dust Prevention
Level Details
4 Prevention of objects larger than 1 mm. Most wires, screws, etc.
Water Prevention
Level Details
2
Vertically dripping water shall have no harmful effect when the enclosure is tilted at an angle up to 15° from its normal position.
35
Opticon
OPR 2001
Specifications Manual
13.5.1.
Cable Strength
No malfunction occurred after the following pulling test.
Pulling test: Fix the scanner and pull the cable with the force of 2.5 kg (24.5N) for
1 second. Repeat 20 times.
13.5.2.
Cable Tail Bending Test
No malfunction occurred after the following bending test.
Bending test: Fix the scanner and attach a weight of 500 grams (4.9N); swing the cable back and forth at an angle of 90°. Repeat it 1,000,000 times.
Figure 26: Cable tail bending test
14. Reliability
MTBF (Mean Time Between Failures) of this product is 10,000 hours.
The estimate of MTBF is based on standard operation of the product within the recommended temperature range and without extreme electronic or mechanical shock.
36
Opticon
OPR 2001
Specifications Manual
15. Trigger and Read Options
15.1. Trigger Modes
Disabled
: When this option is selected, the reader will stay on all the time.
Enabled
: After receiving a trigger signal, the barcode reader will turn on and the read cycle starts. The reader will stay on for a time as set in 'Read time options'. The trigger signal can be initiated in the following ways:
Manual mode
: When the trigger key is pressed, the read cycle starts. In manual mode, you can also use single-line aiming mode when there are multiple printed codes, but you want to scan only one. Use single-line mode to tell the scanner to read only codes aimed at with a single line. The single line is activated by the manual trigger key.
Auto trigger mode
: The read cycle automatically starts when a trigger signal is received via sensor detection.
Serial mode
: The read cycle starts at the time set in 'Read time options' after a serial command (<ESC>Z<CR>) is received.
15.2. Read Modes
Single read mode
: When a symbol has been decoded, the reader will be turned off. The reader must be triggered again to read another symbol. This option and 'Disable trigger' cannot be programmed at the same time.
Multiple read mode
: When a symbol has been decoded, the reader will stay on for a time (set by 'Read time options') or indefinitely, if the trigger switch has been disabled.
The same symbol can only be decoded again after the symbol has not been detected for a set number of scans (multiple read reset time).
Continuous read mode
: The reader will produce as much data as it can decode even if it is reading the same symbol. This mode is mainly used for demonstration and diagnosis.
37
Opticon
OPR 2001
Specifications Manual
15.3. Auto Trigger Options
15.3.1.
Auto Trigger Sensor
The product has an optional auto trigger setting, which starts barcode reading automatically by using sensor detection. The scanner starts barcode reading after detecting reflection from the surface when the auto trigger is used.
Auto trigger distance: 50 ±10 mm from the edge of the scanner.
Conditions
Moving Speed:
Angle:
100 ±10 mm/s (the moving direction is not specified)
Skew angle, excluding Pitch Angle and Dead Zone, specified in section 7.3 Pitch, Skew and Tilt.
Room temperature and humidity Environmental Temperature and Humidity:
Environmental Illuminance: 500 to 900 lx
Conditions for the auto trigger:
1. Barcode sheet: OPTOELECTRONICS Test Sheet (white)
Background: OPTOELECTRONICS Test Sheet (black)
2. Barcode sheet: OPTOELECTRONICS Test Sheet (black)
Background: OPTOELECTRONICS Test Sheet (white)
Figure 27: Auto trigger operation
Auto trigger can be enabled in 2 ways:
• Stand detection mode: This option enables auto trigger automatically in case the scanner is inserted into the stand.
• Normal auto trigger mode.
*Descriptions in ( ) show menu IDs.
38
Opticon
OPR 2001
Specifications Manual
Figure 28: Trigger options
39
Opticon
OPR 2001
Specifications Manual
16. Trigger and Read Settings
16.1.1.
Enable/Disable Settings
Use the following settings to enable or disable the auto trigger. (Auto trigger is disabled by default).
To enable auto trigger, scan “ZZ”, “+I” and “ZZ” in that order.
To disable auto trigger, scan “ZZ”, “+F” and “ZZ” in that order.
Functions Menu labels Menu codes
SET
Enable auto trigger
Disable auto trigger
END
_ZZ_
_+I_
_+F_
_ZZ_
ZZ
+I
+F
ZZ
Note:
Please configure the following after enabling the auto trigger.
16.2. Auto Trigger Stand Detection Settings
16.2.1.
Stand Only
Enable auto trigger only when the scanner is inserted into the stand.
Functions Menu labels Menu codes
SET
Enable auto trigger
Enable auto trigger stand detection
END
_ZZ_
_+I_
_*4_
_ZZ_
ZZ
+I
*4
ZZ
(If the scanner is removed from the stand, auto trigger is disabled and the scanner should be triggered manually.)
40
Opticon
OPR 2001
Specifications Manual
16.2.2.
Always
Enable auto trigger all the time.
Functions Menu labels Menu codes
SET
Enable auto trigger
Disable auto trigger stand detection
END
_ZZ_
_+I_
_*5_
_ZZ_
ZZ
+I
*5
ZZ
16.2.3.
Manually
Only trigger manually (default).
Functions Menu labels Menu codes
SET
Disable auto trigger
Disable auto trigger stand detection
END
_ZZ_
_+F_
_*4_
_ZZ_
ZZ
+F
*5
ZZ
A magnetic switch and a magnet are used for stand detection operation.
Therefore, auto trigger may be activated when there is a magnetic substance nearby.
41
Opticon
OPR 2001
Specifications Manual
17. Regulatory Compliance
17.1. Laser Safety
The scanner emits laser beams.
JIS C6802: 2005: Laser class 2
IEC 825-1/EN 60825-1: Laser class 2
FDA CDRH Laser class II. Complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to laser notice No. 50 dated June 24, 2007.
Class II laser devices are not considered to be hazardous when used for their intended purpose. Avoid staring into the laser beam.
17.2. Product Safety
EN60950-1: 2001
IEC60950-1: 2001
17.3. EMC
EN55022
EN55024
VCCI Class B: This is a Class B product, to be used in a domestic environment based on the Technical Requirement of the Voluntary Control Council for Interference from
Information Technology Equipment (VCCI). If this is used near a radio or television receiver in a domestic environment, it may cause radio interference. Please install and use the equipment according to the instruction manual.
FCC Part 15 Subpart B Class B: This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
17.4. RoHS
RoHS: The restriction of the use of certain hazardous substances in electrical and electronic equipment, 2002/95 EC.
42
Opticon
OPR 2001
Specifications Manual
18. Safety
Handle this product carefully. Do not deliberately subject it to any of the following.
18.1. Shock
Do not throw or drop the scanner.
Do not place heavy objects on the cables.
18.2. Temperature Conditions
Do not use the scanner at temperatures outside the specified range.
Do not pour boiling water on the scanner.
Do not throw the scanner into the fire.
Do not forcibly bend the cables at low temperatures.
18.3. Foreign Materials
Do not immerse the scanner in liquids.
Do not subject the scanner to chemicals.
18.4. Other
Do not plug/unplug the connectors before disconnecting the power.
Do not disassemble this product.
Do not place the product near a radio or a TV receiver, as the scanner may cause reception problems.
The scanner may be damaged by voltage drops.
The scanner may not perform properly in environments when placed near a flickering light, such as a computer monitor, television, etc.
Opticon shall not be held responsible for any damages caused by using an AC adapter not provided by Opticon.
43
19. Mechanical Drawing
Dimensions: 151.0 mm x 56.0 mm x 30.5 mm (except protruding parts)
Opticon
OPR 2001
Specifications Manual
Figure 29: Mechanical drawing
44
Download
Public link updated
The public link to your chat has been updated. You may view and manage your chat links after registration here.
Document public link
Advertisement
