Opticon Nlv-1001 Specification Manual
Opticon NLV-1001 is a compact fixed-position laser barcode scanner designed for various applications. With its short-wavelength red laser beam, it delivers accurate and reliable scanning performance. The NLV-1001 features a compact design, making it ideal for space-constrained environments. It can read various barcode symbologies, including popular 1D and 2D codes. The scanner offers flexible connectivity options, including RS-232C, USB, and wedge interfaces, making it compatible with a wide range of systems.
Advertisement
Advertisement
Compact Fixed Position Laser Scanner
NLV 1001
The NLV 1001 is a compact fixed-position laser barcode scanner, using short-wavelength red laser beam.
Specifications Manual
Opticon
NLV 1001
Specifications Manual
All information subject to change without notice.
Document History
Model Number:
Edition:
Date:
NLV 1001
5A
2008-12-02
Specification Number:
Original Spec Number:
SS06037
SS06079
Copyright 2008 Opticon. All rights reserved.
This manual may not, in whole or in part, be copied, photocopied, reproduced, translated or converted to any electronic or machine readable form without prior written consent of Opticon.
Limited Warranty and Disclaimers
PLEASE READ THIS MANUAL CAREFULLY BEFORE INSTALLING OR USING THE
PRODUCT.
Serial Number
A serial number appears on all Opticon products. This official registration number is directly related to the device purchased. Do not remove the serial number from your Opticon device. Removing the serial number voids the warranty.
Warranty
Unless otherwise agreed in a written contract, all Opticon products are warranted against defects in materials and workmanship for two years after purchase. Opticon will repair or, at its option, replace products that are defective in materials or workmanship with proper use during the warranty period. Opticon is not liable for damages caused by modifications made by a customer. In such cases, standard repair charges will apply. If a product is returned under warranty and no defect is found, standard repair charges will apply. Opticon assumes no liability for any direct, indirect, consequential or incidental damages arising out of use or inability to use both the hardware and software, even if Opticon has been informed about the possibility of such damages.
Packaging
The packing materials are recyclable. We recommend that you save all packing material to use should you need to transport your scanner or send it for service. Damage caused by improper packaging during shipment is not covered by the warranty.
Trademarks
Trademarks used are the property of their respective owners.
Opticon Inc. and Opticon Sensors Europe B.V. are wholly owned subsidiaries of OPTOELECTRONICS Co., Ltd., 12-17,
Tsukagoshi 4-chome, Warabi-shi, Saitama, Japan 335-0002. TEL +81-(0) 48-446-1183; FAX +81-(0) 48-446-1184
SUPPORT
USA Europe
Phone: 800-636-0090
Email: [email protected]
Web: www.opticonusa.com
Email: [email protected]
Web: www.opticon.com
2
Opticon
NLV 1001
Specifications Manual
Contents
1.
Abstract ....................................................................................................................................... 7
2.
Overview...................................................................................................................................... 7
3.
Physical Features ....................................................................................................................... 8
3.1.
Dimensions ......................................................................................................................... 8
3.2.
Weight ................................................................................................................................. 8
4.
Environmental Specifications ................................................................................................... 8
4.1.
Operating Temperature and Humidity................................................................................. 8
4.2.
Storage Temperature and Humidity .................................................................................... 8
4.3.
Ambient Light Immunity....................................................................................................... 8
5.
Electrical Specifications ............................................................................................................ 9
5.1.
Absolute Maximum Ratings ................................................................................................ 9
5.2.
Recommended Operating Conditions ................................................................................. 9
5.3.
Electrical Characteristics..................................................................................................... 9
6.
Optical Specifications .............................................................................................................. 10
6.1.
Laser Scan Specifications................................................................................................. 10
7.
Technical Specifications.......................................................................................................... 10
7.1.
Print Contrast Signal (PCS) .............................................................................................. 10
7.2.
Minimum Resolution.......................................................................................................... 10
7.3.
Scan Area and Resolution ................................................................................................ 11
7.3.1.
Depth of Field...........................................................................................................................11
7.4.
Pitch, Skew, and Tilt.......................................................................................................... 12
7.4.1.
Pitch Angle...............................................................................................................................12
7.4.2.
Skew Angle and Dead Zone ....................................................................................................13
7.4.3.
Tilt Angle ..................................................................................................................................14
7.5.
Curvature .......................................................................................................................... 15
8.
Interface Specifications ........................................................................................................... 15
8.1.
RS-232C Interface Spec ................................................................................................... 15
8.1.1.
Settings and Communication ...................................................................................................15
8.1.2.
Signal Level..............................................................................................................................16
8.1.3.
Interface Circuit........................................................................................................................16
8.1.4.
Character Format.....................................................................................................................17
8.1.5.
Communication Format............................................................................................................17
3
Opticon
NLV 1001
Specifications Manual
8.1.6.
Handshaking ............................................................................................................................17
8.1.7.
OK/NG Signal Output Timing...................................................................................................23
8.2.
USB Interface Specifications............................................................................................. 25
8.2.1.
Interface ...................................................................................................................................25
8.2.2.
Interface Circuit........................................................................................................................25
8.3.
Wedge Interface Specifications......................................................................................... 25
9.
Cable and Connector ............................................................................................................... 26
9.1.
RS-232C Cable ................................................................................................................. 26
9.1.1.
(Standard Specification)...........................................................................................................26
9.1.2.
D-sub Specification ..................................................................................................................26
9.1.3.
Connector Pin-outs ..................................................................................................................27
9.2.
USB Cable ........................................................................................................................ 28
9.2.1.
Connector.................................................................................................................................29
9.2.2.
Connector Pin-outs ..................................................................................................................29
9.3.
Wedge Cable .................................................................................................................... 29
9.3.1.
Connectors...............................................................................................................................30
9.3.2.
Connector Pin-outs ..................................................................................................................30
9.4.
Connector Specification (Scanner Side) ........................................................................... 31
10.
Default Settings ........................................................................................................................ 31
10.1.
Set Default Interface ......................................................................................................... 31
10.2.
Default Settings 1: Readable Codes ................................................................................. 33
10.3.
Default Settings 2: Read Options, Trigger, Buzzer ........................................................... 34
11.
Serial Number and Labeling .................................................................................................... 35
11.1.
Serial Number ................................................................................................................... 35
11.2.
FCC Label ......................................................................................................................... 35
12.
Packaging Specifications ........................................................................................................ 36
12.1.
Individual Packaging Specification.................................................................................... 36
12.2.
Collective Packaging Specification ................................................................................... 36
13.
Durability ................................................................................................................................... 37
13.1.
Electrical Noise ................................................................................................................. 37
13.2.
Static Electricity................................................................................................................. 37
13.3.
Shock ................................................................................................................................ 37
13.3.1.
Drop Test (without packaging).................................................................................................37
13.4.
Vibration Strength ............................................................................................................. 37
4
Opticon
NLV 1001
Specifications Manual
13.5.
Dust and Drip Proof........................................................................................................... 38
14.
Reliability................................................................................................................................... 38
15.
Trigger and Read Options ....................................................................................................... 38
15.1.
Auto Trigger Sensor .......................................................................................................... 38
15.2.
Auto Trigger Enable/Disable Settings ............................................................................... 39
16.
Regulatory Compliance ........................................................................................................... 40
16.1.
Laser Safety ...................................................................................................................... 40
16.2.
Product Safety................................................................................................................... 40
16.3.
EMC .................................................................................................................................. 40
16.4.
RoHS................................................................................................................................. 40
17.
Safety......................................................................................................................................... 41
17.1.
Shock ................................................................................................................................ 41
17.2.
Temperature Conditions.................................................................................................... 41
17.3.
Foreign Materials .............................................................................................................. 41
17.4.
Other ................................................................................................................................. 41
18.
Mechanical Drawing ................................................................................................................. 42
Table of Figures
Figure 1: Scan area and resolution ............................................................................................11
Figure 2: Pitch ............................................................................................................................ 12
Figure 3: Skew angle and dead zone ......................................................................................... 13
Figure 4: Tilt angle ...................................................................................................................... 14
Figure 5: Curvature..................................................................................................................... 15
Figure 6: Interface circuit ............................................................................................................ 16
Figure 7: Character format (same for both sending and receiving) ............................................ 17
Figure 8: Communication format ................................................................................................ 17
Figure 9: No handshaking .......................................................................................................... 17
Figure 10: Busy/Ready communication...................................................................................... 18
Figure 11: Cannot receive command.......................................................................................... 19
Figure 12: Signal timing.............................................................................................................. 19
Figure 13: Handshaking—modem.............................................................................................. 20
Figure 14: Handshaking—ACK/NAK .......................................................................................... 21
Figure 15: Handshaking—ACK/NAK, no response .................................................................... 22
Figure 16: Good read (synchronous).......................................................................................... 23
Figure 17: Read error (synchronous) ......................................................................................... 24
Figure 18: Good read (one shot) ................................................................................................ 24
Figure 19: Read error (one shot) ................................................................................................ 24
Figure 20: Interface circuit .......................................................................................................... 25
Figure 21: RS-232C cable (standard)......................................................................................... 26
Figure 22: RS-232C cable (D-sub) ............................................................................................. 26
5
Opticon
NLV 1001
Specifications Manual
Figure 23: 9-pin D sub female connector (with power stereo jack)............................................. 27
Figure 24: USB cable ................................................................................................................. 28
Figure 25: USB "A" connector .................................................................................................... 29
Figure 26: Wedge cable.............................................................................................................. 29
Figure 27: Connector (host side) ................................................................................................ 30
Figure 28: Connector (keyboard side) ........................................................................................ 30
Figure 29: Serial number diagram .............................................................................................. 35
Figure 30: FCC label .................................................................................................................. 35
Figure 31: Packaging the NLV 1001 ........................................................................................... 36
Figure 32: Auto trigger detection area ........................................................................................ 39
Figure 33: Mechanical drawing................................................................................................... 42
6
Opticon
NLV 1001
Specifications Manual
1. Abstract
This manual provides specifications for the NLV 1001 compact fixed-position laser barcode scanner.
2. Overview
The NLV 1001 is a fixed-position laser barcode scanner.
The scanning width at the closest point of scanning is 44 mm, and the effective scan angle is
44°.
The use of short-wavelength red laser beams enhances the visibility of scanning lines.
The decoded text of barcode images is output through RS-232C, USB, or Wedge interfaces based on the specification.
Supported symbologies:
Linear (1D) Postal
JAN/UPC/EAN, incl. add-on
Codabar/NW-7
Code 11
Code 39
Chinese Post
Korean Postal Authority code
Code 93
Code 128
GS1-128 (EAN-128)
IATA
Industrial 2of5
Interleaved 2of5
ISBN-ISMN-ISSN
Matrix 2of5
MSI/Plessey
GS1-Databar (RSS )
S-Code
Telepen
Tri-Optic
UK/Plessey
2D
Composite Codes
MicroPDF417
PDF417
7
Opticon
NLV 1001
Specifications Manual
3.1. Dimensions
W 30.0 X D 43.3 X H 20.0 mm
3.2. Weight
18.5 g max (excluding cable)
4.1. Operating Temperature and Humidity
Temperature: -10 to +45 °C
Humidity: 20% to 85% RH
4.2. Storage Temperature and Humidity
Temperature: -20 to +60°C
Humidity: 20% to 90% RH
4.3. Ambient Light Immunity
Decoding performance is guaranteed when the range of illumination on a barcode surface is between zero and the following values:
Incandescent Light
Fluorescent Light
Sunlight to 3000 lx to 3000 lx to 50,000 lx
Conditions
Barcode Sample: OPTOELECTRONICS Test Sample
PCS: 0.9
Symbology:
Quiet zone:
N/W ratio:
9-digit Code 39
10 mm
1:2.5
Angle (see note below): α = 0° β = 15° γ = 0°
Power supply voltage: 5.0 V
Direct light or specular reflection from a light source should be prevented from entering the acceptance area.
Note: α, β and γ respectively represent pitch, skew and tilt. Please see section 0 for how these values are defined.
8
Opticon
NLV 1001
Specifications Manual
5.1. Absolute Maximum Ratings
Power supply voltage (V cc
to GND)
Input voltage
Power ripple
Storage temperature
V
DD
V
IN
TSTG
-0.5 to 6.5
-0.5 to VCC+0.5
0.1
Ｖp-p Max.
(10–100 kHz)
-20 to 60
V
V
V
°C
5.2. Recommended Operating Conditions
Item Symbol
Power supply voltage
Condition
V
DD
4.5
Unit
Non-condensing
Non-freezing
Input voltage V in
0 - 45 °C
－ V
DD
Ｖ
Output voltage V out
V
DD
Ｖ
5.3. Electrical Characteristics
V
CC
=5V Ta=25°C
Operating current
Rush current peak
Standby current
Startup time
I
OP
I
PEEK
I
PRE
- 35 70 mA
T
D
- 100 - ms
Conditions:
• Connect 1Ω resistance to a power supply line in series and measure the current by the voltage between both ends of resistance.
• Power supply voltage is measured at a connector terminal area.
• The current value depends on the interface type and host computer to which the device is connected.
9
Opticon
NLV 1001
Specifications Manual
6.1. Laser Scan Specifications
Light emitting diode
Wavelength
Output power
Scanning method
Scanning rate
Scanning angle
Effective scanning angle
Red laser diode
650 ± 10
＜1.0
Bi-directional
100 ± 20
54 ± 5
44 (Min)
- nm mW
- scans/s
°
°
The conditions for technical specifications are as follows, unless otherwise specified in each section.
Conditions
Ambient temperature and humidity: Room temperature (5 to 35º C)
Room humidity (45% to 85% RH)
Ambient light: 500 to 900 lx
Background:
Power supply voltage:
Decoding test:
Barcode = black
Space = white
Margin = white
Background of label = black
5.0 V
0.5 seconds or less for each decoding.
Repeat this 10 times.
7.1. Print Contrast Signal (PCS)
0.45 or higher (over 70% of reflectivity of space and quiet zone).
PCS=
Reflectance of white bar －Reflectance of black bar
Reflectance of white bar
Scanning performance may decline if dirt or scratches mar the optical window. Keep the optical window clean.
7.2. Minimum Resolution
0.127 mm
10
Opticon
NLV 1001
Specifications Manual
7.3. Scan Area and Resolution
7.3.1. Depth of Field
The depth of field is measured from the edge of the scanner. The scanning range is within the circular arc centered on the scan origin.
Figure 1: Scan area and resolution
Symbology Resolution (mm) Decode Depth (mm) PCS
Code 39
Code 39
Code 39
Code 39
Code 39
1.0
0.5
0.25
0.15
0.127
70–630
50–400
50–240
50–130
60–100
0.9
0.9
0.9
0.9
0.9
11
Conditions:
Barcode Sample: OPTOELECTRONICS Test Sample
N/W Ratio:
Angle:
1:2.5
α = 0°, β = 15°, γ = 0°
1.0 mm
0.5 mm
0.25 mm
0.15 mm
0.127 mm
7.4. Pitch, Skew, and Tilt
7.4.1. Pitch Angle
α = ±35°
Code 39
Code 39
Code 39
Code 39
Code 39
0.9
0.9
0.9
0.9
0.9
25 mm
18 mm
10 mm
7 mm
5 mm
1
3
8
10
4
Opticon
NLV 1001
Specifications Manual
Figure 2: Pitch
12
7.4.2.
Opticon
NLV 1001
Specifications Manual
Skew Angle and Dead Zone
Skew angle: β = ±50° (Excluding dead zone)
Dead zone: β = ±8 °(Areas in which decoding fails due to specular reflection)
Figure 3: Skew angle and dead zone
13
Opticon
NLV 1001
Specifications Manual
7.4.3. Tilt Angle
γ = ±20°
Figure 4: Tilt angle
Conditions:
Barcode Sample: OPTOELECTRONICS Test Sample
Distance:
Label:
100 mm from the edge of the scanner
Angle:
Pitch Angle, Skew Angle, Dead Zone
PCS = 0.9, Resolution = 0.25 mm, Symbology = 9-digit Code-39,
Quiet Zone = 10 mm, N/W Ratio = 1:2.5
Tilt Angle
PCS = 0.9, Resolution = 0.26 mm, Symbology = 13-digit JAN, Quiet Zone = 10 mm
Curvature: R = ∞, Skew Angle β = +15° (for measuring pitch angle and tilt angle)
14
Opticon
NLV 1001
Specifications Manual
7.5. Curvature
With 8-digit JAN barcodes, decoding performance is guaranteed when R ≥ 15 mm.
With 13-digit JAN barcodes, decoding performance is guaranteed when R ≥ 20 mm.
Figure 5: Curvature
Conditions:
Barcode Sample: OPTOELECTRONICS Test Sample
PCS = 0.9, Resolution = 0.26 mm, Quiet Zone = 10 mm
Distance: 100 mm from the edge of the scanner
8.1. RS-232C Interface Spec
8.1.1. Settings and Communication
Reading menu barcodes [ZZ] + [U2] + [ZZ] can set the RS-232C interface default.
Baud rate
Start/stop bits
Data bits
Parity bits
9600 BPS
1 bit
8 bits
No parity
Flow control time out
•
Indefinitely
You can change the communication condition using the menu barcode.
15
8.1.2. Signal Level
Signal Name I/O
TxD
RxD
RTS
CTS
OUT
IN
OUT
IN
8.1.3. Interface Circuit
RS-232C Level (V)
-5 to -15
-3 to -15
-5 to -15
-3 to -15
+5 to +15
+3 to +15
+5 to +15
+3 to +15
Opticon
NLV 1001
Specifications Manual
Figure 6: Interface circuit
16
Opticon
NLV 1001
Specifications Manual
8.1.4. Character Format
Figure 7: Character format (same for both sending and receiving)
8.1.5. Communication Format
Figure 8: Communication format
8.1.6. Handshaking
Select handshaking options using the menu or command listed below.
Handshaking Menu/Command
No handshake P0
BUSY/READY P1
MODEM P2
ACK/NAK P3
ACK/NAK NO RESPONSE P4
The scanner attempts the communication regardless of the state of the host computer.
Figure 9: No handshaking
17
Opticon
NLV 1001
Specifications Manual b) BUSY/READY
The scanner and the host computer notify each other of their state and whether they can receive data with BUSY/READY through an RS line. They can communicate state to each other through a CTS line when connected as in the following figure.
Figure 10: Busy/Ready communication
The scanner stays ON (is able to receive data) except during certain parts of the process, such as receiving data (buzzer command execution), transmitting data, and menu processing. The scanner checks the CTS line before transmitting data. When it is ON, the scanner transmits data. When it is OFF, the scanner waits for it to turn ON within a set time. The scanner will abort transmission with an error indication (buzzer) when the CTS line is not ON within a specified period. The Flow Control time-outs are as follows, and the default setting is “indefinitely“ (I0).
Flow Control Time Out Menu/Command
Indefinitely I0
100 ms I1
200 ms I2
400 ms I3
18
Opticon
NLV 1001
Specifications Manual
Figure 11: Cannot receive command
CTS, T×D signals timing
When the CTS line is turned OFF while sending a T×D signal, the scanner transmits one character and waits. When the CTS signal is turned ON while transmitting a character, the character will be transmitted.
Figure 12: Signal timing
Note: When using loopback (wire connection) for RTS, CTS line of the scanner in this setting,
No handshake
is not enabled.
19
Opticon
NLV 1001
Specifications Manual c) MODEM
The scanner turns the RTS line ON before transmitting data. Other processes are the same as BUSY/READY.
Figure 13: Handshaking—modem
20
Opticon
NLV 1001
Specifications Manual d) ACK/NAK
After data has been transmitted, the scanner expects to receive one of the following responses from the host:
• ACK response—Action: The scanner completes transmission with the good-read buzzer and returns to the initial state.
•
•
NAK response—Action: The scanner sends the data again and waits for the response from the host.
DC1 response—Action: The scanner returns to waiting for the trigger, if it has a trigger (the initial state).
• None response—Action: The scanner sounds the error buzzer and returns to the initial state.
ACK/NAK timeout can be set as follows using the menu or commands.
•
•
•
•
I4: Indefinitely (default)
I5: 100 ms
I6: 500 ms
I7: 1000 ms
Figure 14: Handshaking—ACK/NAK
21
Opticon
NLV 1001
Specifications Manual
When no response from the host is received within the setting time, the scanner assumes an ACK response, and returns to the initial state without the error buzzer. The other actions are the same as ACK/NAK.
Figure 15: Handshaking—ACK/NAK, no response
22
Opticon
NLV 1001
Specifications Manual
8.1.7. OK/NG Signal Output Timing
(NLV 1000 RS-232C Standard Only) The output ON/OFF or the logic can be selected by the menus or commands listed below.
Functions Menu/Command
SYNC Synchronous H active
SYNC Synchronous L active
One shot H active
One shot L active
One shot time 10 ms
One shot time 20 ms
One shot time 30 ms
One shot time 40 ms
One shot time 50 ms
One shot time 60 ms
One shot time 70 ms
One shot time 80 ms
One shot time 90 ms
One shot time 100 ms
Enable sequence output
Disable sequence output
X*C (default)
X*D
X*E
X*F
X*G
X*H
X*I
X*J
X*K
X*L
X*M
X*N
X*O
X*P (default)
X*Q (default)
X*R
The following figures show examples of output timing when using a pull-up resistor, since the OK/NG output is the FET open drain output. a) Good Read (Synchronous)
Figure 16: Good read (synchronous)
23
b) Read Error within Specified Time (Synchronous)
Opticon
NLV 1001
Specifications Manual
Figure 17: Read error (synchronous) c) Good Read (One Shot)
Figure 18: Good read (one shot) d) Read Error within Specified Time (One Shot)
Figure 19: Read error (one shot)
24
8.2. USB Interface Specifications
8.2.1. Interface
The interface is full-speed USB 1.1.
8.2.2. Interface Circuit
Opticon
NLV 1001
Specifications Manual
Figure 20: Interface circuit
8.3. Wedge Interface Specifications
Set the language for the scanner and PC keyboard to the same language before use; otherwise, the output may not be correct.
Do not use the host keyboard while data is being transmitted to the host, or the data may be transmitted incorrectly.
25
9. Cable and Connector
9.1. RS-232C Cable
9.1.1. (Standard Specification)
Type:
Diameter:
Figure 21: RS-232C cable (standard)
Straight
φ3.8±0.5 mm
Cores: 8 insulated wires, 1 conductive wire
9.1.2. D-sub Specification
Opticon
NLV 1001
Specifications Manual
Figure 22: RS-232C cable (D-sub)
26
Type:
Diameter:
Length:
Cores:
Straight
φ3.8±0.5 mm
1500±50 mm or 500±50 mm
8 insulated wires, 1 conductive wire
9.1.3. Connector Pin-outs
Signal Pin Remarks
F.GND Shield (Black) Cover shielded wire with heat-shrinkable tubing
GND Black
VCC Red
TxD Green
RxD White
RTS Grey
CTS Blue
NG Orange
OK Yellow
TRIGGER Brown b) D-sub Specification
(1) D-sub
Opticon
NLV 1001
Specifications Manual
Figure 23: 9-pin D sub female connector (with power stereo jack)
27
9.2. USB Cable
(Standard specification)
Pin Signal
1 F.GND
2 TxD
3 RxD
4 NC
5 GND
6 NC
7 CTS
8 RTS
9 NC
Pin Signal Remarks
Opticon
NLV 1001
Specifications Manual
Figure 24: USB cable
Type:
Diameter:
Length:
Cores:
Straight
φ3.8 ±0.5 mm
1500 ±50 mm
4 insulated wires, 1 conductive wire
28
Opticon
NLV 1001
Specifications Manual
9.2.1. Connector
USB "A" Connector
Figure 25: USB "A" connector
9.2.2. Connector Pin-outs
Contact Number Signal Name
1 VCC
2 -DATA
3 +DATA
4 GND
Do not use the host keyboard while data is being transmitted to the host, or the data may be transmitted incorrectly.
9.3. Wedge Cable
(Standard specification)
#1O
#1
Figure 26: Wedge cable
29
Type:
Diameter:
Length:
Cores:
Y cable
φ3.8 ±0.5 mm
1500 ±50 mm
6 insulated wires, 1 conductive wire
9.3.1. Connectors
Figure 27: Connector (host side)
Figure 28: Connector (keyboard side)
9.3.2. Connector Pin-outs
Contact
Number
Host Side Keyboard Side
1 CPU DATA KEY DATA
2 OPEN OPEN
3 GND GND
4 VCC VCC
5 CPU CLOCK KEY CLOCK
6 OPEN OPEN
Opticon
NLV 1001
Specifications Manual
30
9.4. Connector Specification (Scanner Side)
CN1 (10-pin)
Pin # Specifications
RS-232C USB WEDGE
1 TRIGGER NC NC
2 OK NC NC
3 NG NC NC
8 VCC VCC VCC
9 GND GND GND
10. Default Settings
10.1. Set Default Interface
Scan the following menu barcodes to return to the default settings.
RS-232C
SET
RS-232C
END
_ZZ_
_U2_
_ZZ_ codes
ZZ
U2
ZZ
USB-HID
SET
USB-HID
END
_ZZ_
_SU_
_ZZ_
31 codes
ZZ
SU
ZZ
Opticon
NLV 1001
Specifications Manual
Opticon
NLV 1001
Specifications Manual
USB-VCP
A driver is required and can be downloaded from Opticon’s support Web site: http://opticonfigure.opticon.com/.
SET
USB-VCP
END codes
_ZZ_
ZZ
_C01_
C01
_ZZ_
ZZ
Wedge (with keyboard)
SET
AT-Wedge
With keyboard
END
_ZZ_
_UB_
_KM_
_ZZ_
Wedge (without keyboard) codes
ZZ
UB
KM
ZZ
SET
AT-Wedge
Without keyboard
END
_ZZ_
_UB_
_KL_
_ZZ_ codes
ZZ
UB
KL
ZZ
32
Opticon
NLV 1001
Specifications Manual
10.2. Default Settings 1: Readable Codes
Code
Length
CD
Calculate
CD
Set
Prefix
Set
Suffix
Other
UPC-A
UPC-A Add-on
UPC-E
UPC-E Add-on
EAN-13
EAN-13 Add-on
EAN-8
EAN-8 Add-on
Codabar/NW-7
X
X
X
X
X
X
X
X
X
X
X
X
X
X
— CR
— CR
— CR
— CR
— CR
— CR
— CR
— CR
— CR Not transmit ST/SP
— CR Code 11 X X X
Code 39 X X — CR Not transmit ST/SP
Code 93 X X — CR
Code 128 X X — CR
X — CR
IATA X X — CR
Industrial2of5 X X — CR
Interleaved2of5 X X — CR
X — CR
MicroPDF417 X X — — —
MSI/Plessey
UK/Plessey
X
X
CD1
RSS-limited X X
RSS-expanded X X
S-Code
Telepen
Trioptic
X
X
X
CD1
X
X
— CR
— CR
— CR
— CR
— CR
CR —
—
—
CR
CR Not transmit ST/SP
33
Opticon
NLV 1001
Specifications Manual
Notes:
In the “Reading” column, “ ” means “Enable reading” and “X” means “Disable reading.”
In the “Transmit code length” column, “ ” means “Transmit code length” and “X” means
“Do not transmit code length.”
In the “Transmit CD” column, “ ” means “Transmit check digit” and “X” means “Do not transmit check digit.”
In the “Calculate CD” column, “ ” means “Calculate check digit” and “X” means “Do not calculate check digit.”
“— “ means “not supported.”
In the “Prefix” column, “—“ means “there is no prefix setting.”
10.3. Default Settings 2: Read Options, Trigger, Buzzer
Setting the number of characters
Read mode
Multiple read reset time
Add-on wait mode
Multiple label read
Multiple column read
Redundancy Default option
([X0] setting)
Other options
([X1 .. X3] setting)
([BS .. BW] setting)
Trigger switch
Trigger repeat
Auto trigger
Read time
Margin check
Buzzer duration
Buzzer tone
Buzzer loudness
Buzzer transmission
Startup buzzer
Good read LED
Fixed length OFF all codes
Multiple read
500 ms
500 ms
Disable
Disable
Read 1 times, redundancy = 0
Read n times, redundancy = n+1 for the following symbologies and lengths:
● Code 11 with length <= 5
● Code 39 with length <= 5
● IATA,Industrial 2of5, Interleaved 2of5 with length <= 8
● Matrix 2of5 (& Chinese Post), Scode with length <= 8
● MSI/Plessey with length <= 4
● NW-7 (Codabar) with all lengths
Enable
Disable
Disable
2 seconds (when trigger enabled)
Normal
50 ms
Single tone (3 kHz)
Maximum
Before transmission
Enable
Indicator duration 200 ms
34
11. Serial Number and Labeling
11.1. Serial Number
The serial number shown below is affixed to the scanner.
Opticon
NLV 1001
Specifications Manual
Figure 29: Serial number diagram
Serial numbers are seven-digit numbers and start from number 0000001 regardless of batch.
11.2. FCC Label
Figure 30: FCC label
35
Opticon
NLV 1001
Specifications Manual
12. Packaging Specifications
12.1. Individual Packaging Specification
Put the scanner in a protective foam bag and place it in an individual packing box.
Size of the package (after assembly): 245 (W) X 110 (D) X 38 (H) mm
12.2. Collective Packaging Specification
BOX f or MSH- 110
（B85006- 15B）
Car t on Box（5B0008）
Packaged 50 set s i nt o t he Car t on- Box .
Ｒｏ
⑥
⑦
⑧
①
②
⑨
⑩
③
④
⑤
Rows
⑤
⑥
⑦
⑧
①
②
③
④
⑨
⑩
The or der of ser i al - No.
1～ 5
5～10
11～15
16～20
21～25
26～30
31～35
36～40
41～45
46～50
Ｒｏ
Ro- 30 Label
( NFT2100- 7070- 0- 00)
* St i ck〝Ro- 30〟Label ont o one si de onl y.
5 St eps
①－1
①－2
①－3
①－4
①－5
Figure 31: Packaging the NLV 1001
Note: The “RO” mark labeled on the package tray or package box guarantees that the applicable product has passed our test of RoHS restrictions compliance (the restriction of the use of certain hazardous substances in electrical and electronic equipment, 2002/95
EC). However, this document does not have any legal weight in the European Union.
36
Opticon
NLV 1001
Specifications Manual
13. Durability
13.1. Electrical Noise
No malfunction occurred when sinusoidal electrical noise (50 Hz–100 kHz, < 0.1 Vp-p) was added to the power supply line.
Conditions
Barcode Sample: OPTOELECTRONICS Test Sample
PCS 0.9
Symbology
Quiet Zone
N/W Ratio
Angle
9-digit Code 39
10 mm
1:2.5
α = 0° β = 15° γ = 0°
Power Supply Voltage 5.0 V
13.2. Static Electricity
Air discharge: ±8 kV max. (No malfunction)
±10 kV max. (No destruction)
Measurement environment:
Use electrostatic testing device compliant with IEC 61000-4-2
Discharge resistance: 330 Ω
Capacitor charging: 150 pF
13.3. Shock
13.3.1. Drop Test (without packaging)
No malfunction occurred after the following drop test.
Drop Test: Drop the scanner from a height of 75 cm onto a concrete floor (once in each of five directions).
13.4. Vibration Strength
No malfunction occurred after the following vibration test.
Vibration test: Increase the frequency of the vibration from 12 Hz to 100 Hz with accelerated velocity 19.6 m/s 2 (2 G) for 60 minutes in non-operating state. Repeat this routine in each X, Y, Z direction once for 60 minutes each.
37
Opticon
NLV 1001
Specifications Manual
13.5. Dust and Drip Proof
IEC IP43
Dust Prevention
Level Details
4 Prevention of objects larger than 1 mm. Most wires, screws, etc.
Water Prevention
Level Details
3 Water falling as a spray at any angle up to 60° from the vertical shall have no harmful effect.
14. Reliability
MTBF (Mean Time Between Failures) of this product except for the laser diode and the mirror motor scan unit is 30,000 hours.
Life cycle of the laser diode is 10,000 hours and that of the mirror motor scan unit is also
10,000 hours.
The estimate of MTBF and product life cycle is based on standard operation of the product within the recommended temperature range and without extreme electronic or mechanical shock.
15. Trigger and Read Options
The NLV 1001 has read and trigger settings as follows:
15.1. Auto Trigger Sensor
When auto trigger is used, the scanner starts barcode reading after detecting a change in reflection in the detection area. The scanner will be triggered if the sensors detect changes in brightness in the detection area.
Auto trigger distance: 50 ±10 mm from the edge of the scanner.
Conditions
Moving speed: 100 ±10 mm/s
Angle:
Environmental temperature and humidity:
Vertical to the edge of the scanner
Room temperature and humidity
Environmental illuminance: 500 to 900 lx
Conditions for the auto trigger:
1. Barcode sheet: OPTOELECTRONICS Test Sheet (white)
Background: OPTOELECTRONICS Test Sheet (black)
2. Barcode sheet: OPTOELECTRONICS Test Sheet (black)
Background: OPTOELECTRONICS Test Sheet (white)
38
Opticon
NLV 1001
Specifications Manual
Figure 32: Auto trigger detection area
15.2. Auto Trigger Enable/Disable Settings
Use the following settings to enable or disable the auto trigger. (Auto trigger is disabled by default).
To enable auto trigger, scan “ZZ”, “+I” and “ZZ” in that order.
To disable auto trigger, scan “ZZ”, “+F” and “ZZ” in that order.
Functions
SET
Disable auto trigger
Enable auto trigger
END
Menu labels Menu codes
_ZZ_
_+F_
_+I_
_ZZ_
ZZ
+F
+I
ZZ
39
Opticon
NLV 1001
Specifications Manual
16. Regulatory Compliance
16.1. Laser Safety
The scanner emits laser beams. Class 2 laser devices are not considered to be hazardous when used for their intended purpose. Avoid staring into the laser beam.
IEC60825-1+A2: 2001 Class 2
JIS-C-6802: 2005 Class 2
FDA CDRH Laser Class 2. Complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to laser notice No. 50 dated June 24, 2007.
16.2. Product Safety
EN60950-1: 2001
IEC60950-1: 2001
16.3. EMC
EN55022
EN55024
VCCI Class B: This is a Class B product, to be used in a domestic environment based on the Technical Requirement of the Voluntary Control Council for Interference from
Information Technology Equipment (VCCI). If this is used near a radio or television receiver in a domestic environment, it may cause radio interference. Please install and use the equipment according to the instruction manual.
FCC Part 15 Subpart B Class B: This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
16.4. RoHS
RoHS: The restriction of the use of certain hazardous substances in electrical and electronic equipment, 2002/95 EC.
40
Opticon
NLV 1001
Specifications Manual
17. Safety
Handle this product carefully. Do not deliberately subject it to any of the following.
17.1. Shock
Do not throw or drop the scanner.
Do not place heavy objects on the cables.
17.2. Temperature Conditions
Do not use the scanner at temperatures outside the specified range.
Do not pour boiling water on the scanner.
Do not throw the scanner into the fire.
Do not forcibly bend the cables at low temperatures.
17.3. Foreign Materials
Do not immerse the scanner in liquids.
Do not subject the scanner to chemicals.
17.4. Other
Do not plug/unplug the connectors before disconnecting the power.
Do not disassemble this product.
Do not place the product near a radio or a TV receiver, as the scanner may cause reception problems.
The scanner may be damaged by voltage drops.
The scanner may not perform properly in environments when placed near a flickering light, such as a computer monitor, television, etc.
41
18. Mechanical Drawing
Dimensions: 30 X 20 X 43.3 mm (cable not shown)
Opticon
NLV 1001
Specifications Manual
Figure 33: Mechanical drawing
42
Download
Public link updated
The public link to your chat has been updated. You may view and manage your chat links after registration here.
Document public link
Advertisement