Leitor Opticon
OPR-3201 Laser
O conjunto optico do OPR3201 está posicionado para
proporcionar estabilidade do laser com movimento da
mão durante a leitura. Juntamente com a pistola
ergonômica estas características tornam mais fácil e
confortável fazer a leitura dos códigos de barras.
www.bztech.com.br
STD-3201
Using the Stand
Quick Start Guide
STEP 1
Scanner
Cradle
Use the Adjusting Screw to connect the
Stand Arm with the Scanner Cradle as
shown in the diagram.
Introduction
• Read this quick start guide carefully before installing or/and using the stand.
• Keep this quick start guide for future reference and store in a safe place.
Stand Arm
CAUTION
• This quick start guide may be revised or withdrawn at any time without prior notice.
• This quick start guide may not, in whole or in part, be copied, photocopied, reproduced, translated or
converted to any electronic or machine readable form without prior written consent of Opticon.
• Trademarks used are property of their respective owners.
• Under no circumstances shall Opticon be held responsible for any special, incidental, consequential or
indirect damages howsoever caused.
Adjust the angle of the Scanner Cradle
by first loosening the Adjusting Screw
and then tightening it once the Scanner
Cradle has been placed in the desired
position.
• The STD-3201 is the designated stand for the OPR-3201 handheld laser scanner.
• Do not dismantle the stand.
• Do not drop the stand.
• Do not install the stand on unstable surfaces.
• Do not place heavy objects on top of the stand.
• Do not expose the scanner to intense heat.
• Do not hold the Scanner Cradle when adjusting the Stand Arm.
Overview
Stand Base
STEP2
STEP 2
Handling Instructions
STEP1
Adjusting Screw
Adjusting Screw
Accessories & Optional Parts
Dimensions
(H) 295 × (W) 106 × (D) 146 mm Max
(H) 11.6 × (W) 5.75 × (D) 4.17 in. Max
Weight
385g Max (13.58 oz / 0.85 lb)
Color
Black or White
Please use commercially
available M3 or M4 screws
to mount the stand.
STEP3
STEP 3
Make sure to place one hand on the Stand
Base and hold the Stand Arm with the
other hand when adjusting the height and
the angle of the stand.
N ote
295mm
Do not hold the Scanner Cradle when adjusting
the Stand Arm.
Contact
Please contact Opticon or your local dealer.
The Netherlands
U.S.A.
N ote
146mm
106mm
Copyright 2007, Opticon All rights reserved.
Over-tightening the screws may cause
the stand to break.
France
Germany
Italy
Spain
Opticon Sensors Europe B.V.
tel: +31 (0)23-5692700 / email: [email protected]
Opticon Inc.
tel: 800-636-0090 / email: [email protected]
Opticon S.A.S.
tel: +33 (0)1-41461260 / email: [email protected]
Opticon Sensoren GmbH
tel: +49 (0)6074-91890-0 / email: [email protected]
Opticon s.r.l.
tel: +39 (0)051-6321800 / email: [email protected]
Opticon Sensores S.L.
tel: +34 (0)902-747469 / email: [email protected]
Sweden
United Kingdom
Taiwan
China
Australia
Brazil
Opticon Sensors Nordic AB
tel: +46 (0)8-58548560 / email: [email protected]
Opticon Limited
tel: +44 (0)1582-635100 / email: [email protected]
Opticon Far Eastern Ltd.
tel: +886 2-27597444 / email: [email protected]
Opticon Sensors Europe B.V., Shanghai Representative Office
tel: +86 21-64480881 / email: [email protected]
Opticon Sensors Pty. Ltd.
tel: +61 (0)2-43402666 / email: [email protected]
Opticon Sensors Europe B.V., Latin American Office
tel: +55 11-8322 2244 / email: [email protected]
5J0081
">
