Opticon OPV 1001 Specification Manual
Advertisement
Advertisement
Laser Multi-barcode Scanner
OPV 1001
The OPV 1001 is a 1000 scans multi-barcode laser scanner reading for omni-directional reading.
Specifications Manual
Opticon
OPV 1001
Specifications Manual
All information subject to change without notice.
Document History
Model Number:
Edition:
Date:
OPV 1001
6
2008-04-07
Specification Number:
Original Spec Number:
SS06175
SS06172
Copyright 2008 Opticon. All rights reserved.
This manual may not, in whole or in part, be copied, photocopied, reproduced, translated or converted to any electronic or machine readable form without prior written consent of Opticon.
Limited Warranty and Disclaimers
PLEASE READ THIS MANUAL CAREFULLY BEFORE INSTALLING OR USING THE
PRODUCT.
Serial Number
A serial number appears on all Opticon products. This official registration number is directly related to the device purchased. Do not remove the serial number from your Opticon device. Removing the serial number voids the warranty.
Warranty
Unless otherwise agreed in a written contract, all Opticon products are warranted against defects in materials and workmanship for two years after purchase. Opticon will repair or, at its option, replace products that are defective in materials or workmanship with proper use during the warranty period. Opticon is not liable for damages caused by modifications made by a customer. In such cases, standard repair charges will apply. If a product is returned under warranty and no defect is found, standard repair charges will apply. Opticon assumes no liability for any direct, indirect, consequential or incidental damages arising out of use or inability to use both the hardware and software, even if
Opticon has been informed about the possibility of such damages.
Packaging
The packing materials are recyclable. We recommend that you save all packing material to use should you need to transport your scanner or send it for service. Damage caused by improper packaging during shipment is not covered by the warranty.
Trademarks
Trademarks used are the property of their respective owners.
Opticon Inc. and Opticon Sensors Europe B.V. are wholly owned subsidiaries of OPTOELECTRONICS Co., Ltd., 12-
17, Tsukagoshi 4-chome, Warabi-shi, Saitama, Japan 335-0002. TEL +81-(0) 48-446-1183; FAX +81-(0) 48-446-1184
SUPPORT
USA Europe
Phone: 800-636-0090
Email: [email protected]
Web: www.opticonusa.com
Email: [email protected]
Web: www.opticon.com
2
Opticon
OPV 1001
Specifications Manual
Contents
1.
Abstract ....................................................................................................................................... 7
2.
Overview...................................................................................................................................... 7
3.
Physical Features ....................................................................................................................... 8
3.1.
Dimensions ......................................................................................................................... 8
3.2.
Weight ................................................................................................................................. 8
4.
Environmental Specifications ................................................................................................... 8
4.1.
Operating Temperature and Humidity................................................................................. 8
4.2.
Storage Temperature and Humidity .................................................................................... 8
4.3.
Ambient Light Immunity....................................................................................................... 8
5.
Electrical Specifications ............................................................................................................ 9
5.1.
Power Supply ...................................................................................................................... 9
5.2.
AC Adapter.......................................................................................................................... 9
5.3.
Operating Indicators............................................................................................................ 9
5.3.1.
Red.............................................................................................................................................9
5.3.2.
Green .........................................................................................................................................9
6.
Optical Specifications .............................................................................................................. 10
6.1.
Laser Scan Specifications................................................................................................. 10
7.
Technical Specifications.......................................................................................................... 10
7.1.
Print Contrast Signal (PCS) .............................................................................................. 10
7.2.
Minimum Resolution.......................................................................................................... 10
7.3.
Scan Area and Resolution ................................................................................................ 11
7.3.1.
Scan Area ................................................................................................................................11
7.3.2.
Depth of Field...........................................................................................................................11
7.4.
Pitch, Skew, and Tilt.......................................................................................................... 13
7.4.1.
Pitch Angle...............................................................................................................................13
7.4.2.
Skew Angle and Dead Zone ....................................................................................................13
7.4.3.
Tilt ............................................................................................................................................14
7.5.
Curvature .......................................................................................................................... 15
8.
Interface Specifications ........................................................................................................... 16
8.1.
RS-232C Interface ............................................................................................................ 16
8.1.1.
Settings and Communication ...................................................................................................16
8.1.2.
Signal Level..............................................................................................................................16
3
Opticon
OPV 1001
Specifications Manual
8.1.3.
Pin Assignment ........................................................................................................................16
8.1.4.
Interface Circuit........................................................................................................................17
8.1.5.
Character Format.....................................................................................................................17
8.1.6.
Communication Format............................................................................................................17
8.1.7.
Handshaking ............................................................................................................................18
8.2.
USB Interface Specifications............................................................................................. 23
8.2.1.
Connector.................................................................................................................................23
8.2.2.
Interface Circuit........................................................................................................................23
8.3.
DOS/V Wedge Interface Specification .............................................................................. 24
8.3.1.
Connectors...............................................................................................................................24
9.
Cable and Connector ............................................................................................................... 26
9.1.
Cables ............................................................................................................................... 26
9.1.1.
RS-232C ..................................................................................................................................26
9.1.2.
USB Cable ...............................................................................................................................26
9.1.3.
DOS V/Wedge Cable ...............................................................................................................27
9.2.
Connectors........................................................................................................................ 27
10.
Default Settings ........................................................................................................................ 27
10.1.
Set Default Interface ......................................................................................................... 27
10.2.
Default Settings 1: Readable Codes ................................................................................. 29
10.3.
Default Settings 2: Read Options, Trigger, Buzzer ........................................................... 30
11.
Serial Number ........................................................................................................................... 31
12.
Packaging Specifications ........................................................................................................ 32
12.1.
Accessory Specifications .................................................................................................. 32
12.2.
Collective Packaging Specification ................................................................................... 33
13.
Durability ................................................................................................................................... 34
13.1.
Static Electricity................................................................................................................. 34
13.2.
Shock ................................................................................................................................ 34
13.2.1.
Drop Test (without packaging).................................................................................................34
13.2.2.
Drop Test (with individual packaging)......................................................................................34
13.3.
Vibration Strength ............................................................................................................. 34
13.4.
Cable Strength .................................................................................................................. 35
13.5.
Cable Bending Test........................................................................................................... 35
14.
Reliability................................................................................................................................... 35
15.
Trigger and Read Options ....................................................................................................... 36
4
Opticon
OPV 1001
Specifications Manual
15.1.
Trigger Modes ................................................................................................................... 36
15.2.
Read modes...................................................................................................................... 36
16.
Trigger and Read Settings ....................................................................................................... 37
16.1.
Auto Trigger Enable/Disable Settings ............................................................................... 37
17.
Power Saving ............................................................................................................................ 38
17.1.
Motor speed ...................................................................................................................... 38
17.2.
Auto Shut-off Time ............................................................................................................ 38
17.3.
Power Saving 2 (Motor Rotation—1/2) ............................................................................. 39
17.4.
Power Saving 3 (Motor Rotation—Stop) ........................................................................... 39
18.
Regulatory Compliance ........................................................................................................... 42
18.1.
Laser Safety ...................................................................................................................... 42
18.2.
Product Safety................................................................................................................... 42
18.3.
EMC .................................................................................................................................. 42
18.4.
RoHS................................................................................................................................. 42
19.
Safety......................................................................................................................................... 43
19.1.
Shock ................................................................................................................................ 43
19.2.
Temperature Conditions.................................................................................................... 43
19.3.
Foreign Materials .............................................................................................................. 43
19.4.
Other ................................................................................................................................. 43
20.
Mechanical Drawing ................................................................................................................. 44
20.1.
OPV 1001 (without stand) ................................................................................................. 44
20.2.
OPV 1001 (with stand) ...................................................................................................... 44
Table of Figures
Figure 1: Scan area .....................................................................................................................11
Figure 2: Depth of field ............................................................................................................... 12
Figure 3: Pitch ............................................................................................................................ 13
Figure 4: Skew and dead zone................................................................................................... 13
Figure 5: Tilt................................................................................................................................ 14
Figure 6: Curvature..................................................................................................................... 15
Figure 7: Interface circuit (RS-232C) .......................................................................................... 17
Figure 8: Character format (same for both sending and receiving) ............................................ 17
Figure 9: Communication format ................................................................................................ 17
Figure 10: No handshaking ........................................................................................................ 18
Figure 11: Busy/Ready communication ...................................................................................... 18
Figure 12: Handshaking Busy/Ready ......................................................................................... 19
Figure 13: Signal timing.............................................................................................................. 19
5
Opticon
OPV 1001
Specifications Manual
Figure 14: Handshaking: Modem mode ..................................................................................... 20
Figure 15: Handshaking: ACK/NAK............................................................................................ 21
Figure 16: Handshaking: ACK/NAK—No response.................................................................... 22
Figure 17: USB "A" connector .................................................................................................... 23
Figure 18: Interface circuit (USB) ............................................................................................... 23
Figure 19: Wedge connector (host side)..................................................................................... 24
Figure 20: Wedge connector (keyboard side)............................................................................. 24
Figure 21: Wedge connector (DOS/V side) ................................................................................ 25
Figure 22: RS-232C cable .......................................................................................................... 26
Figure 23: USB cable ................................................................................................................. 26
Figure 24: Wedge cable.............................................................................................................. 27
Figure 25: Serial number diagram .............................................................................................. 31
Figure 26: Individual packaging diagram .................................................................................... 32
Figure 27: Collective packaging.................................................................................................. 33
Figure 28: Drop test.................................................................................................................... 34
Figure 29: Cable tail bending test............................................................................................... 35
Figure 30: Auto-trigger detection area ........................................................................................ 37
Figure 31: Menu code combinations (part 1) .............................................................................. 40
Figure 32: Menu code combinations (part 2) .............................................................................. 41
Figure 33: Mechanical drawing (without stand) .......................................................................... 44
Figure 34: Mechanical drawing(with stand) ................................................................................ 44
6
Opticon
OPV 1001
Specifications Manual
1. Abstract
This manual provides specifications for the OPV 1001 laser multi-barcode scanner.
2. Overview
The OPV 1001 outputs laser beams in multiple directions (4 lines each in 5 directions) to scan barcodes. For non-contact scanning, a barcode needs to face the scan window of the
OPV 1001.
For periods of inactivity, the power saving mode (laser disabled, motor off) can be set using commands or menu barcodes. Power saving mode will be automatically disabled when the brightness in front of the scanner is changed; for example, when an object is placed in front of the scanner.
You can use a dedicated stand (an accessory, sold separately) to adjust the height and angle of the scanner.
The feature settings of the OPV 1001 are configured either by scanning menu barcodes or by sending commands.
The OPV 1001 outputs scanned data through any of the following interfaces: RS-232C,
Keyboard Wedge, or USB.
Supported symbologies:
Linear (1D) Postal Code
JAN/UPC/EAN, incl. add-on Chinese Post
Codabar/NW-7
Code 11
Code 39
Code 93
Code 128
GS1-128 (EAN-128)
IATA
Industrial 2of5
Interleaved 2of5
ISBN-ISMN-ISSN
Matrix 2of5
MSI/Plessey
S-Code
Telepen
Tri-Optic
UK/Plessey
7
Opticon
OPV 1001
Specifications Manual
3.1. Dimensions
(Without stand) W 71.0 x D 79.4 x H 100.0 mm
3.2. Weight
OPV 1001: 200 g (max.) excluding the cable
Stand: 340 g (max.)
4.1. Operating Temperature and Humidity
Temperature: 0 to +40° C
Humidity: 20 to 90% RH
4.2. Storage Temperature and Humidity
Temperature: -30 to +60° C
Humidity: 20 to 90% RH
4.3. Ambient Light Immunity
Decoding performance is guaranteed when the range of illumination on a barcode surface is between zero and the following values:
Incandescent light
Fluorescent light
3,000 lx
3,000 lx
Conditions
Barcode Sample: OPTOELECTRONICS Test Sample
PCS: 0.9
Symbology:
Quiet zone:
N/W ratio:
9-digit Code 39
10 mm
1:2.5
Angle (see note below): α = 0° β = 15° γ = 0°
Power supply voltage: 5.0 V
Direct light or specular reflection from a light source should be prevented from entering the acceptance area.
Note: α , β and γ respectively represent pitch, skew and tilt. Please see section 0 for how these values are defined.
8
Opticon
OPV 1001
Specifications Manual
5.1. Power Supply
Input voltage
Power ripple
Current consumption
DC 5 V ±5 % (6 V also supported) up to 100 mVp-p (10 Hz to 100 kHz DC 5V) up to 500 mA
•
•
Conditions:
• Connect 1 Ω resistance to a power supply line in series and measure the current by the voltage between both ends of resistance.
Power supply voltage is measured at a connector terminal area.
The current value depends on the interface type and the host computer to which the device is connected.
5.2. AC Adapter
Input:
Input voltage
Power supply frequency
Maximum current
Rush current
Output:
Output voltage
Output ripple
Maximum current
Startup time
AC 90 V to 264 V
47 Hz to 63 Hz up to 400 mA (at 100 V AC/50 Hz) up to 70 A
DC 5 V ±5% (6 V also supported) up to 100 mVp-p
2000 mA up to 20 ms (AC100V/50 Hz, 5% to 95% of output voltage)
5.3. Operating Indicators
5.3.1. Red
• Lights up when any unsupported menu is read in the menu mode (200 ms with error buzzer).
• Blinks when motor failure occurs (indefinitely).
5.3.2. Green
• Good read: when reading is done successfully.
9
Opticon
OPV 1001
Specifications Manual
6.1. Laser Scan Specifications
Parameter Specification Unit
Light-emitting element
Emission wavelength
Light output
Scanning method
Scanning speed
Red laser diode
650 ±10 (25° C)
1.0 or less (measured at the front of the scanner’s plastic mask)
Rastering omni-directional scanning
1000 ±50
– nm mW
– scans/s
The conditions for technical specifications are as follows, unless otherwise specified in each section.
Conditions
Ambient temperature and humidity: Room temperature (5 to 35º C)
Room humidity (45% to 85% RH)
Ambient light:
Background:
500 to 1000 lx
Barcode = black
Space = white
Margin = white
Background of label = black
Power supply voltage:
Decoding test:
5.0 V
Approve the performance when decoding is successful in all ten tests.
(Decoding is deemed successful when completed in 0.5 seconds or less.)
7.1. Print Contrast Signal (PCS)
0.45 or higher (over 70% of reflectivity of space and quiet zone).
PCS=
Reflectance of white bar － Reflectance of black bar
Reflectance of white bar
Scanning performance may decline if dirt or scratches mar the optical window. Keep the optical window clean.
7.2. Minimum Resolution
0.127 mm
10
Opticon
OPV 1001
Specifications Manual
7.3. Scan Area and Resolution
7.3.1. Scan Area
The scannable area depends on the barcode type (PCS, resolution, length, etc.) and the direction of the barcode surface. However, the barcode should be set within the following area.
Figure 1: Scan area
Note: Binary codes are more likely to cause scanning errors than multi-level codes. To minimize problems, fix the length of binary codes.
7.3.2. Depth of Field
The depth of field is measured from the edge of the scanner.
The scanning range is within the circular arc centered on the scan origin.
11
Opticon
OPV 1001
Specifications Manual
Figure 2: Depth of field
0.9
0.9
0.9 or higher
0.9
(mm)
0.66
0.33
0.2
0.127
(mm)
70 - 230
15 - 200
15 - 110
15 - 50
Resolution
(mm)
Symbology Digit
0.66 JAN-8 8
0.33 JAN-13 13 Test
0.2
0.127
Code 39
Code 39
7
4
Laser printer labels
OPTOELECTRONICS Test Sample
Conditions
Barcode Sample: OPTOELECTRONICS Test Sample
N/W Ratio:
Angle:
1:2.5
α = 0°, β = 15°, γ = 0°
12
7.4. Pitch, Skew, and Tilt
7.4.1. Pitch Angle
α = ±35°
Opticon
OPV 1001
Specifications Manual
Figure 3: Pitch
7.4.2. Skew Angle and Dead Zone
Skew angle: β = ±50° (Excluding dead zone)
Dead zone: β = ±8° (There are some areas in which decoding fails due to specular reflection)
Figure 4: Skew and dead zone
13
7.4.3.
Opticon
OPV 1001
Specifications Manual
Tilt
γ = 360°
There are some angles at which decoding fails, depending on the height of a barcode.
Figure 5: Tilt
Conditions
Barcode Sample: OPTOELECTRONICS Test Sample
Distance:
Label:
70 mm from the front edge of the scanner
Pitch, Skew Angle
PCS = 0.9, Resolution = 0.33 mm, Symbology = JAN-13
Position
The center of the barcode and the scan line are almost the same (refer to the following figure).
Angle:
Curvature: Ｒ = ∞ , skew angle β = +10 ° (for measuring pitch angle and tilt angle)
Note: The specifications are decided on one horizontal scan line, except Tilt.
14
Opticon
OPV 1001
Specifications Manual
7.5. Curvature
With 8-digit JAN/UPC/EAN barcodes, decoding performance is guaranteed when
R ≥ 20 mm.
With 13-digit JAN/UPC/EAN barcodes, decoding performance is guaranteed when
R ≥ 25 mm.
Figure 6: Curvature
Conditions
Barcode Sample: OPTOELECTRONICS Test Sample
PCS = 0.9, Resolution = 0.33 mm
15
Opticon
OPV 1001
Specifications Manual
The interface type is determined automatically, depending on the cable type.
8.1. RS-232C Interface
8.1.1. Settings and Communication
Baud rate
Start/stop bits
Data bits
Parity bits
9600 bps
1 bit
8 bits
No parity
Flow control time out Indefinitely
You can change the communication condition using the menu barcode.
8.1.2. Signal Level
Signal
Name
I/O RS-232C Level (V)
Mark/OFF Space/ON
TxD
RxD
OUT
IN
-5 to -15
-3 to -15
+5 to +15
+3 to +15
RTS
CTS
OUT
IN
-5 to -15
-3 to -15
+5 to +15
+3 to +15
8.1.3. Pin Assignment
Signals Pin
NC
1
TxD
RxD
－
GND
Remarks
2
3
4 Jumper to pin 6
－
CTS
5
6 Jumper to pin 4
RTS
NC
7
8
9
Connector: D-sub 9-pin female
16
8.1.4. Interface Circuit
Opticon
OPV 1001
Specifications Manual
Figure 7: Interface circuit (RS-232C)
8.1.5. Character Format
Figure 8: Character format (same for both sending and receiving)
8.1.6. Communication Format
Figure 9: Communication format
17
8.1.7.
Opticon
OPV 1001
Specifications Manual
Handshaking
Select handshaking options using the menu or command listed below.
Handshaking Menu/Command
No handshake P0
BUSY/READY P1
MODEM P2
ACK/NAK P3
ACK/NAK NO RESPONSE P4
The scanner attempts the communication regardless of the state of the host computer.
Figure 10: No handshaking b) BUSY/READY
The scanner and the host computer notify each other of their state and whether they can receive data with BUSY/READY through an RTS line.
They can communicate state to each other through a CTS line when connected as in the following figure.
Figure 11: Busy/Ready communication
The scanner stays ON (is able to receive data) except during certain parts of the process, such as receiving data (buzzer command execution), transmitting data, and menu processing. The scanner checks the CTS line before transmitting data. When it is ON, the scanner transmits data. When it is OFF, the scanner waits for it to turn ON within a set time. The scanner will abort transmission with an error indication (buzzer) when the CTS line
18
Opticon
OPV 1001
Specifications Manual is not ON within a specified period. The Flow Control time-outs are as follows, and the default setting is “indefinitely“ (I0).
Flow Control Time Out Menu/Command
Indefinitely I0
100 ms I1
200 ms
400 ms
I2
I3
Figure 12: Handshaking Busy/Ready
CTS, TxD Signals Timing
When the CTS line (RTS signal on the host side) is turned OFF while sending a TxD signal, the scanner transmits one character and waits.
When the CTS signal is turned ON while transmitting a character, the character will be transmitted.
Figure 13: Signal timing
Note: When using loopback (wire connection) for RTS, CTS line of the scanner in this setting, No Handshake is not enabled.
19
Opticon
OPV 1001
Specifications Manual c) MODEM
The scanner turns RTS line ON before transmitting data. Other processes are the same as BUSY/READY.
Figure 14: Handshaking: Modem mode
20
Opticon
OPV 1001
Specifications Manual d) ACK/NAK
After data has been transmitted, the scanner expects to receive one of the following responses from the host:
ACK response—Action: The scanner completes transmission with the good-read buzzer and returns to the initial state.
•
•
•
•
NAK response—Action: The scanner sends the data again and waits for the response from the host.
DC1 response—Action: The scanner returns to waiting for the trigger, if it has a trigger (the initial state).
None response—Action: The scanner sounds the error buzzer and returns to the initial state.
ACK/NAK timeout can be set as follows using the menu or commands.
I4: Indefinitely (default)
I5: 100 ms
I6: 500 ms
I7: 1000 ms
Figure 15: Handshaking: ACK/NAK
21
Opticon
OPV 1001
Specifications Manual
When no response from the host is received within the setting time, the scanner assumes an ACK response, and returns to the initial state without the error buzzer. The other actions are the same as ACK/NAK.
Figure 16: Handshaking: ACK/NAK—No response
22
Opticon
OPV 1001
Specifications Manual
8.2. USB Interface Specifications
8.2.1. Connector a) USB "A" connector
Figure 17: USB "A" connector
Contact Number Signal Name Notes
1 VCC signal
2 -DATA
3 +DATA
4 GND
8.2.2. Interface Circuit
Figure 18: Interface circuit (USB)
23
Opticon
OPV 1001
Specifications Manual
8.3. DOS/V Wedge Interface Specification
8.3.1. Connectors
Figure 19: Wedge connector (host side)
Contact Number Signal Name Notes
3 GND b) DOS/V Keyboard Side
Figure 20: Wedge connector (keyboard side)
Contact Number Signal Name Notes
2 OPEN
3 GND
4 VCC
6 OPEN
24
Opticon
OPV 1001
Specifications Manual
Figure 21: Wedge connector (DOS/V side)
Contact Number Signal Name Notes
2 OPEN
3 GND
4 VCC
6 OPEN
Note: To connect a PS2 port that supports both a mouse and a keyboard, please use the Y cable that is packaged with the scanner.
25
9. Cable and Connector
9.1. Cables
(Standard specification)
Type: Straight (with power jack – RS-232C, DOS/V Wedge only)
Diameter: φ 3.8 mm (main cable), φ 3 mm (AC adapter cable)
Length: 2000 ±50 mm (excluding main cable and connector)
250 ±20 mm (excluding AC adapter cable and jack)
Cores:
Weight:
8 insulated wires, 1 conductive wire (USB interface cable)
Approximately 85 g max. (excluding connector)
9.1.1. RS-232C
Opticon
OPV 1001
Specifications Manual
9.1.2. USB Cable
Figure 22: RS-232C cable
26
Figure 23: USB cable
Opticon
OPV 1001
Specifications Manual
9.1.3. DOS V/Wedge Cable
Figure 24: Wedge cable
9.2. Connectors
RS-232C interface: D-Sub 9-pin (female) connector
DOS/V Wedge interface: Mini-DIN 6-pin (female) connector
USB interface: USB-A connector
10. Default Settings
10.1. Set Default Interface
Scan the following menu barcodes to return to the default settings.
RS-232C
Functions
SET
RS-232C
END
Menu labels
_ZZ_
_U2_
_ZZ_
Menu codes
ZZ
U2
ZZ
USB-HID
Functions
SET
USB-HID
END
Menu labels
_ZZ_
_SU_
_ZZ_
Menu codes
ZZ
SU
ZZ
27
USB-VCP
Functions
SET
USB-VCP
END
Menu labels
_ZZ_
_C0_
_ZZ_
Menu codes
ZZ
C01
ZZ
Wedge (with keyboard)
Functions
SET
AT-Wedge
With keyboard
END
Menu labels
_ZZ_
_UB_
_KM_
_ZZ_
Wedge (without keyboard)
Functions
SET
AT-Wedge
Without keyboard
END
Menu labels
_ZZ_
_UB_
_KL_
_ZZ_
Menu codes
ZZ
UB
KM
ZZ
Menu codes
ZZ
UB
KL
ZZ
Opticon
OPV 1001
Specifications Manual
28
Opticon
OPV 1001
Specifications Manual
10.2. Default Settings 1: Readable Codes
UPC-A
UPC-A Add-on
UPC-E
UPC-E Add-on
EAN-13
EAN-13 Add-on
EAN-8
EAN-8 Add-on
Chinese Post
Codabar/NW-7
X
X
X
X
X
Code
Length
X
X
X
X
X
X
X
X
X
X
CD
Calculate
CD
Code 11
Code 39
X
X
X
X
X
Code 93
Code 128
IATA
Industrial2of5
Interleaved2of5
ISBN Japan code
X
X X
X X
EAN-128 X
X
X
X
X
X
X
X
Matrix2of5 X
MSI/Plessey
UK/Plessey
S-Code
Telepen
Tri-Optic
X
X
X
X X
X
X
X
X
X
X
Set
Prefix
Set
Suffix
－
－
－
－
－
－
－
－
－
－
－
－
－
－
－
－
－
－
－
－
－
－
－
－
Other
CR
CR
CR
CR
CR
CR
CR
CR
CR
ST/SP
CR transmit
ST/SP
CR
CR
CR
CR
CR
CR
13 twice
CR
CR
CR
CR
CR
ST/SP
Notes:
• In the “Reading” column, “ ” means “Enable reading” and “X” means “Disable reading.”
• In the “Transmit code length” column, “ ” means “Transmit code length” and
“X” means “Do not transmit code length.”
29
Opticon
OPV 1001
Specifications Manual
• In the “Transmit CD” column, “ ” means “Transmit check digit” and “X” means
“Do not transmit check digit.”
• In the “Calculate CD” column, “ ” means “Calculate check digit” and “X” means “Do not calculate check digit”.
• In the “Prefix” column, “-” means “There is no prefix setting”.
• For the Wedge and USB interfaces, there are no suffix settings.
• The output contents for JAN ISBN code depends on the setting of EAN-13.
The output result is the same as transmitting EAN-13 twice.
10.3. Default Settings 2: Read Options, Trigger, Buzzer
Setting the number of characters
Read mode
Multiple read reset time
Add-on wait mode
Multiple column read
Redundancy
Intercharacter gap check (NW-7)
Read time
Buzzer duration
Buzzer tone
Buzzer loudness
Good read LED
Set minimum length
Fixed length OFF all codes
Multiple read
500 ms
500 ms
Disable
Read 2 times, redundancy = 1
Within 0.5 characters
2 seconds
100 ms
2.6 kHz
Maximum
Indicator duration 200 ms
Code 11: 1 character
Code 39: 1 character
Code 93: 1 character
Code 128: 1 character
Codabar/NW-7: 5 characters
EAN 128: 1 character
IATA: 5 characters
Industrial 2of5: 5 characters
Interleaved 2of5: 6 characters
MSI/Plessey: 3 characters
UK/Plessey: 2 characters
S-Code: 5 characters
Telepen: 5 characters
30
11. Serial Number
The serial number shown below is affixed to the scanner.
Opticon
OPV 1001
Specifications Manual
Figure 25: Serial number diagram
31
Opticon
OPV 1001
Specifications Manual
12. Packaging Specifications
Put the scanner in a protective foam bag and place it in an individual packing box with the accessories.
Size of the package (after assembly): 165 (W) X 255 (D) X 150 (H) mm
PROTECTI ON BAG G
（B87004-57）
Col or - Ti e：5H0001
（4× 180／Bl ack）
OSE User ' s Manual
（5J0063A）
① AC ADAPTOR
St opped wi t h a Scot ch t ape.
* Put AC- Adapt or & Pl ugs
* ①&② ar e one pr oduct .
AC Adapt er ( Hel ms- Man)
：SFP0602000P- PSE
② Pl ugs
( 4 ki nds)
STAND SET( BLACK)
（XFOPE0007)
BOX（B00005- 41）
AC ADAPTOR wi t h 4Pl ugs
STAND SET
OSE User ' s Manual
Face t he opt i cal wi ndow down when you put t he scanner i n t he box.
Figure 26: Individual packaging diagram
12.1. Accessory Specifications
The following table shows a list of accessories for each model.
OPV 1001-RS-232C
OPV 1001-USB
OPV 1001-Wedge
(GP-ACGN13x-K4-2)
Yes
N/A
Yes
(B04061-300)
N/A
N/A
Yes
32
12.2. Collective Packaging Specification
Put 20 single packages into the packing box.
Size of the package (after assembly): 530 (W) X 850 (D) X 325 (H) mm
Opticon
OPV 1001
Specifications Manual
Compl et e- set
Car t on- Box（B00005- 42）
Packaged 20 set s i nt o t he Car t on- Box.
⑥
⑦
①
②
⑧
⑨
⑩
③
④
⑤
２St eps
①
⑥
⑦
⑧
⑨
⑩
②
③
④
⑤
１ ～ ２
３ ～ ４
５ ～ ６
７ ～ ８
９ ～１０
１１ ～１２
１３ ～１４
１５ ～１６
１７ ～１８
１９ ～２０
１
２
A ： Barcode Serial Label for Packaging Box:
Stick the labels on both front and back side of the box.
（3C0006）
B ： Missing Serial Number Label:
Attach this label when there are more than 3 labels of which
serial numbers are out of order (not in a correct sequence).
（3C0007）
UNI VERSAL
C/ No.
△ △
MADE I N JAPAN
Pr oduct
UNI VERSAL C/ No.
△ △
MADE I N JAPAN
PO#
Missi ng Ser i al Number Missi ng Q' t y △ △
* △ △ △ △ - △ △ *
Spec#JPN 3
* △ △ △ △ △ △ *
4
Spec#EUR
* △ △ △ △ △ △ *
5
Spec#USA
* △ △ △ △ △ △ *
6
* △ △ △ △ △ △ *
Q' t y
△ △ / △ △ △
*△ △ *
S/ N( f r om)
*000001*
S/ N( t o)
*
7
8
* △ △ △ △ △ △ *
9
* △ △ △ △ △ △ *
*
△ △ △ △ △ △
*
1 1 0
* △ △ △ △ △ △ * * △ △ △ △ △ △ *
1 1
2
* △ △ △ △ △ △ *
* △ △ △ △ △ △ *
1 2
*
△ △ △ △ △ △
*
ROM- Ver .
Shi ppi ng Dat e
TP09J △ △
2008/ △ △ / △ △
Ｒｏ
OPTO ELECTRONI CS Co. , Lt d.
OPTO ELECTRONI CS Co. , Lt d.
Figure 27: Collective packaging
Note: The “RO” mark labeled on the package tray or package box guarantees that the applicable product has passed our test of RoHS restrictions compliance (the restriction of the use of certain hazardous substances in electrical and electronic equipment, 2002/95 EC). However, this document does not have any legal weight in the European Union.
33
Opticon
OPV 1001
Specifications Manual
13. Durability
13.1. Static Electricity
Air discharge: ±8 kV max. (No malfunction)
±15 kV max. (No destruction)
Contact discharge: ±4 kV max. (No malfunction)
±8 kV max. (No destruction)
Use electrostatic testing device compliant with IEC 61000-4-2 Measurement environment:
Discharge resistance: 330 Ω
Capacitor charging: 150 pF
13.2. Shock
13.2.1. Drop Test (without packaging)
No malfunction occurred after the following drop test.
Drop Test: Drop the scanner from a height of 100 cm onto a concrete floor
(three times on each of 6 sides).
Figure 28: Drop test
13.2.2. Drop Test (with individual packaging)
No malfunction occurred after the following drop test.
Drop Test: Drop an individually packaged scanner from a height of 100 cm onto a concrete floor once on its 1 corner, 3 edges, and 6 sides (10 total drop tests).
13.3. Vibration Strength
No malfunction occurred after the following vibration test.
Vibration test: Increase the frequency of the vibration from 10 Hz to 100 Hz with accelerated velocity 19.6 m/s 2 (2 G) for 60 minutes in non-operating state. Repeat this routine in each X, Y, Z direction once for 60 minutes each.
34
Opticon
OPV 1001
Specifications Manual
13.4. Cable Strength
No malfunction occurred after the following cable strength test.
Affix the scanner to an immovable object, then pull it using a force of 2.5 kgf for 1 second. Carry out this test 20 times.
13.5. Cable Bending Test
No malfunction occurred after the following cable bending test.
Bending test: Affix the scanner to a flat surface and attach a weight of 250 grams.
Swing the cable back and forth at an angle of 60 degrees. Repeat 500,000 times.
Figure 29: Cable tail bending test
14. Reliability
MTBF (Mean Time Between Failures) of this product except for the laser diode and the mirror motor scan unit is 20,000 hours.
Life cycle of the laser diode is 10,000 hours and that of the mirror motor scan unit is also
10,000 hours.
The estimate of MTBF and product life cycle is based on standard operation of the product within the recommended temperature range and without extreme electronic or mechanical shock.
35
Opticon
OPV 1001
Specifications Manual
15. Trigger and Read Options
The OPV 1001 has read and trigger settings as follows:
15.1. Trigger Modes
• Disabled: When this option is selected, the reader will stay on all the time.
• Enabled: After receiving a trigger signal, the barcode reader will turn on and the read cycle starts. The reader will stay on for a time as set in 'Read time options'.
The trigger signal can be initiated in the following ways:
• Manual mode: When the trigger is depressed, the read cycle starts.
• Auto trigger mode: The read cycle automatically starts when a trigger signal is received via sensor detection.
• Serial mode: The read cycle starts for a time as set in 'Read time options' after a serial command (<ESC>Z<CR>) is received.
• Hardware mode: After an electrical pulse (low), the read cycle starts for a time as set in 'Read time options' and behaves as if the trigger is continuously depressed.
15.2. Read modes
• Single read mode: When a symbol has been decoded, the reader will be turned off. The reader must be triggered again to read another symbol. This option and
'Disable trigger' cannot be programmed at the same time.
•
•
Multiple read mode: When a symbol has been decoded, the reader will stay on for a time (set by 'Read time options') or indefinitely, if the trigger switch has been disabled. The same symbol can only be decoded again after the symbol has not been detected for a set number of scans.
Continuous read mode: The reader will produce as much data as it can decode even if it is reading the same symbol. This mode is mainly used for demonstration and diagnosis.
Conditions
Moving speed:
Environmental temperature and humidity:
Environmental illuminance:
Conditions for the auto trigger:
0.6 m/s
Room temperature and humidity
100 to 20,000 lx
Slide the color sample ”Cool Gray-7U” (PANTONE) onto the basic color sample ”Black on Black” (PANTONE).
Slide the color sample “Black on Black” onto the basic color sample “Cool Gray-7U”.
36
Opticon
OPV 1001
Specifications Manual
Figure 30: Auto-trigger detection area
16. Trigger and Read Settings
16.1. Auto Trigger Enable/Disable Settings
Use the following settings to enable or disable the auto trigger. (Auto trigger is disabled by default).
To enable auto trigger, scan “ZZ”, “+I” and “ZZ” in that order.
To disable auto trigger, scan “ZZ”, “+F” and “ZZ” in that order.
Functions
SET
Disable auto trigger
Enable auto trigger
END
Menu labels
_ZZ_
_+F_
_+I_
_ZZ_
Menu codes
ZZ
+F
+I
ZZ
37
Opticon
OPV 1001
Specifications Manual
17. Power Saving
The motor options are only applicable for selected laser bar code readers and with trigger enabled. If the read time is expired, the motor can be switched OFF. When the trigger is activated, the motor is switched ON again. To reduce the start-up time of the motor, the motor can be configured to half speed in idle mode. The Auto shutoff time can be configured between 1 and 9999 seconds, by reading 1 up to 4 direct input numeric characters from chapter: String options. A value of 0 (default) means that the barcode reader enters the idle state if the read time has expired.
17.1. Motor speed
Functions
SET
Menu codes
ZZ
Motor half speed when idle
Disable motor when idle
Enable motor when idle
Disable trigger
Enable trigger
END
Menu labels
_ZZ_
_BBA_
_4Z_
_4Y_
_S7_
_S8_
_ZZ_
BBA
4Z
4Y
S7
S8
ZZ
17.2. Auto Shut-off Time
Functions
SET
Auto shut-off time
Direct input numeric
(set time for power saving)
END
Menu labels
_ZZ_
_BBB_
Use direct input labels
_ZZ_
Menu codes
ZZ
BBB
Q0 – Q9
ZZ
38
Opticon
OPV 1001
Specifications Manual
The enabled time for power saving can be set from 0 to 9999 seconds. Use the direct input numeric 0 to 4 digits after BBB to set the time.
Example:
0 second
1 seconds
12 seconds
123 seconds
“BBB” or “BBB” + “Q0”
“BBB” + “Q1”
“BBB” + “Q1” + “Q2”
“BBB” + “Q1” + “Q2” + “Q3”
1234 seconds
9999 seconds
“BBB” + “Q1” + “Q2” + “Q3” + “Q4”
“BBB” + “Q9” + “Q9” + “Q9” + “Q9”
Disable power saving mode “ZZ” + “BBB” + “ZZ”
17.3. Power Saving 2 (Motor Rotation—1/2)
Functions
SET
Motor half speed when idle
Enable motor when idle
END
Menu labels
_ZZ_
_BBA_
_4Y_
_ZZ_
Menu codes
ZZ
BBA
4Y
ZZ
17.4. Power Saving 3 (Motor Rotation—Stop)
Functions Menu labels Menu codes
SET
Disable motor when idle
Enable motor when idle
END
_ZZ_
_4Z_
_4Y_
_ZZ_
ZZ
4Z
4Y
ZZ
The power mode transition of Motor / Laser in each setting combination (7 total) is shown below.
39
Opticon
OPV 1001
Specifications Manual
Figure 31: Menu code combinations (part 1)
40
Opticon
OPV 1001
Specifications Manual
Figure 32: Menu code combinations (part 2)
41
Opticon
OPV 1001
Specifications Manual
18. Regulatory Compliance
18.1. Laser Safety
The scanner emits laser beams.
JIS C6802: 2005: Laser class 1
IEC 825-1/EN 60825-1: Laser class 1
FDA CDRH Laser class 1. Complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to laser notice No. 50 dated June 24, 2007.
Class 1 laser devices are not considered to be hazardous when used for their intended purpose. Avoid staring into the laser beam.
18.2. Product Safety
EN60950-1: 2001
IEC60950-1: 2001
18.3. EMC
EN55022
EN55024
VCCI Class B: This is a Class B product, to be used in a domestic environment based on the Technical Requirement of the Voluntary Control Council for Interference from
Information Technology Equipment (VCCI). If this is used near a radio or television receiver in a domestic environment, it may cause radio interference. Please install and use the equipment according to the instruction manual.
FCC Part 15 Subpart B Class B: This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
18.4. RoHS
RoHS: The restriction of the use of certain hazardous substances in electrical and electronic equipment, 2002/95 EC.
42
Opticon
OPV 1001
Specifications Manual
19. Safety
Handle this product carefully. Do not deliberately subject it to any of the following.
19.1. Shock
Do not throw or drop the scanner.
Do not place heavy objects on the cables.
19.2. Temperature Conditions
Do not use the scanner at temperatures outside the specified range.
Do not pour boiling water on the scanner.
Do not throw the scanner into the fire.
Do not forcibly bend the cables at low temperatures.
19.3. Foreign Materials
Do not immerse the scanner in liquids.
Do not subject the scanner to chemicals.
19.4. Other
Do not plug/unplug the connectors before disconnecting the power.
Do not disassemble this product.
Do not place the product near a radio or a TV receiver, as the scanner may cause reception problems.
The scanner may be damaged by voltage drops.
The scanner may not perform properly in environments when placed near a flickering light, such as a computer monitor, television, etc.
43
20. Mechanical Drawing
20.1. OPV 1001 (without stand)
Opticon
OPV 1001
Specifications Manual
Figure 33: Mechanical drawing (without stand)
20.2. OPV 1001 (with stand)
1 1 2
1 0 0
Figure 34: Mechanical drawing(with stand)
44
Download
Public link updated
The public link to your chat has been updated. You may view and manage your chat links after registration here.
Document public link
Advertisement
