User Manual UMA

™

Mixer/Amplifiers

Intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

Intended to alert the user of the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

C AU TIIO N:: Risk of electrical shock — DO NOT OPEN!

C AU TIIO N:: To reduce the risk of electric shock, do not remove cover. No user serviceable parts inside.

Refer servicing to qualified service personnel.

WA RN G:: To prevent electrical shock or fire hazard, do not expose this appliance to rain or moisture.

Before using this appliance, read the operating guide for further warnings.

Este símbolo tiene el propósito, de alertar al usuario de la presencia de “(voltaje) peligroso” sin aislamiento dentro de la caja del producto y que puede tener una magnitud suficiente como para constituir riesgo de descarga eléctrica.

Este símbolo tiene el propósito de alertar al usario de la presencia de instruccones importantes sobre la operación y mantenimiento en la información que viene con el producto.

P RE AU CIIO N:: Riesgo de descarga eléctrica ¡NO ABRIR!

P RE AU CIIO N:: Para disminuír el riesgo de descarga eléctrica, no abra la cubierta. No hay piezas útiles dentro. Deje todo mantenimiento en manos del personal técnico cualificado.

A DV TE NC humedad este aparato Antes de usar este aparato, Iea más advertencias en la guía de operación.

Ce symbole est utilisé dans ce manuel pour indiquer à l’utilisateur la présence d’une tension dangereuse pouvant être d’amplitude suffisante pour constituer un risque de choc électrique.

Ce symbole est utilisé dans ce manuel pour indiquer à l’utilisateur qu’il ou qu’elle trouvera d’importantes instructions concernant l’utilisation et l’entretien de l’appareil dans le paragraphe signalé.

A TT TIIO N:: Risques de choc électrique — NE PAS OUVRIR!

A TT TIIO N:: Afin de réduire le risque de choc électrique, ne pas enlever le couvercle. Il ne se trouve à l’intérieur aucune pièce pouvant être reparée par l’utilisateur. Confiez I’entretien et la réparation de l’appareil à un réparateur Peavey agréé.

A VE TIIS SE EN appareil à la pluie ou à l’humidité. Avant d’utiliser cet appareil, lisez attentivement les avertissements supplémentaires de ce manuel.

Dieses Symbol soll den Anwender vor unisolierten gefährlichen Spannungen innerhalb des Gehäuses warnen, die von Ausreichender Stärke sind, um einen elektrischen Schlag verursachen zu können.

Dieses Symbol soll den Benutzer auf wichtige Instruktionen in der Bedienungsanleitung aufmerksam machen, die Handhabung und Wartung des Produkts betreffen.

V OR SIIC T:: Risiko — Elektrischer Schlag! Nicht öffnen!

V OR SIIC T:: Um das Risiko eines elektrischen Schlages zu vermeiden, nicht die Abdeckung enfernen. Es befinden sich keine Teile darin, die vom Anwender repariert werden könnten. Reparaturen nur von qualifiziertem Fachpersonal durchführen lassen.

A CH UN

Regen oder Feuchtigkeit ausgesetzt werden. Vor Inbetriebnahme unbedingt die Bedienungsanleitung lesen.

2

R ea d T hiiss!!

IIM PO AN T S AFFE TY TR UC TIIO S

10.

11.

12.

13.

14.

W RN

1.

2.

3.

4.

5.

6.

7.

8.

9.

15.

16.

Read these instructions.

Keep these instructions.

Heed all warnings.

Follow all instructions.

Do not use this apparatus near water. For example, near or in a bathtub, swimming pool, sink, wet basement, etc.

Clean only with a damp cloth.

Do not block any of the ventilation openings. Install in accordance with manufacturer’s instructions. It should not be placed flat against a wall or placed in a built-in enclosure that will impede the flow of cooling air.

Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus (including amplifiers) that produce heat.

Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding plug. The wide blade or third prong is provided for your safety. When the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. Never break off the grounding. Write for our free booklet “Shock Hazard and Grounding.” Connect only to a power supply of the type marked on the unit adjacent to the power supply cord.

Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point they exit the apparatus.

Only use attachments/accessories provided by the manufacturer.

Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus..

Unplug this apparatus during lightning storms or when unused for long periods of time.

Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

If this product is to be mounted in an equipment rack, rear support should be provided.

Exposure to extremely high noise levels may cause permanent hearing loss. Individuals vary considerably in susceptibility to noise-induced hearing loss, but nearly everyone will lose some hearing if exposed to sufficiently intense noise for a sufficient time. The U.S. Government’s Occupational and Health

Administration (OSHA) has specified the following permissible noise level exposures:

Sound Duration Per Day In Hours

8

6

4

3

2

1 1/2

1

1/2

1/4 or less

Sound Level dBA, Slow Response

90

92

95

97

100

102

105

110

115

According to OSHA, any exposure in excess to the above permissible limits could result in some hearing loss. Ear plugs or protectors in the ear canals or over the ears must be worn when operating this amplification system in order to prevent a permanent hearing loss, if exposure is in excess to the limits as set forth above. To ensure against potentially dangerous exposure to high sound pressure levels, it is recommended that all persons exposed to equipment capable of producing high sound pressure levels such as this amplification system be protected by hearing protectors while this unit is in operation.

S AV E T HE E IIN ST UC ON S!!

3

D es pttiio n

F ea urre s

U A err//A mp

The UMA 352, 752, and 1502 are high quality, commercial grade analog audio mixer/amplifiers.

Designed for flexibility in application, these mixer/amps represent the latest, state-of-the-art technology in analog circuit design.

Powerful, yet easy to use, the new UMA series delivers amazing sonic performance. Low-noise design and features applicable to “real-world” situations make these units ideal for audio applications where a compact, powered mixer with multiple input and output capabilities are required.

This manual was written to provide as much information as possible for your new Peavey

Architectural Acoustics product. It is our sincere desire that you enjoy your purchase.

We feel that the best way to fully enjoy any purchase is to have an in-depth understanding of the product’s features, functionality, and performance characteristics. We hope that this manual, along with the manuals of our other products, will provide this. If you require additional information that this manual does not provide, please let us know. We are continuously looking for better ways to provide information about our products, and your input is always appreciated.

If you have a comment about this manual, or would like to make a suggestion, please write to:

Peavey Electronics Corp., Architectural Acoustics Division, 711 A St., Meridian, MS 39301. Thank you for using Peavey Architectural Acoustics!

• Up to five input channels

• One electronically balanced Mic/Tel input – telephone input with 600 Ohm transformer balanced for paging

• One electronically balanced Mic/Line input

• Two electronically balanced Line inputs

• One plug-in module port allows for any single-space MMA ™ module

• Rear-panel input level control for optional MMA input module

• Priority/Muting system with internal signal override, external switch closure capability, threshold control, and front panel indicators

• Mute Bus Active/Defeat switches on two channels

• Remote volume control capability

• Bass and treble equalization controls

• Preamp output and power amp input loop for external processing equipment or auxiliary output

• Channel 4 electronically balanced output provides non-mutable output for MOH

• Front panel channel input signal level indicators

• Amplifier signal indicator

• SPS ™ (Speaker Protection System) circuitry with indicator

• Power indicator

• 4 Ohm direct output

• 8 Ohm, 70 Volt, and 100 Volt transformer-isolated power outputs

• AC convenience outlet (120 V units only)

• Optional rack mounting with included rack ears

4

A pp attiio s

• Presentation Rooms

• Board Rooms

• Courtrooms

• Auditoriums

• Lecture Halls

• Meeting Rooms

• Convention Centers

• Paging Systems

• Background Music

• Retail Spaces

• Restaurants

Frro ntt P ell

7

11..

1 2

3 4 5

6 8

9

IIN PU T C HA NE VE ON TR

These rotary controls set the channel signal level sent to the mix bus.

IIN PU T C AN NE MU TE DIIC TO S::

These red LEDs indicate that the corresponding channel is muted.

IIN PU T C AN NE SIIG NA TA US CA TO S::

These bi-color LEDs indicate signal presence (-20 dBu) via green illumination, and imminent clipping (2 dB below clipping point) via red illumination.

LLO W E Q ((B AS

This rotary control varies low frequency response from +10 dB to -10 dB at 100 Hz. It is a shelving-type active control and delivers a flat response in the center “0” position.

HIIG H E Q ((T RE

This rotary control varies high frequency response from +10 dB to -10 dB at 10 kHz. It is a shelving-type active control and delivers a flat response in the center “0” position.

SIIG NA VE DIIC TO

This green LED will illuminate as an indication of signal presence at the amplifier output.

S S IIN DIIC TO

This yellow LED will illuminate as an indication of SPS activation. SPS is a compression circuit that senses signal conditions that have the potential to overload the amp, and reduces the system gain when clipping is imminent.

M AS ER ELL::

This rotary control sets the overall signal level of the system.

P OW R IIN DIIC TO

This green LED illuminates as an indication that mains power is being applied to the unit.

5

B acck an

15 16 17 18 19 20 30

10 11 12 13 14 21 24 25 26 27 28 29 31 32 33

IIE C C NN CT R::

This receptacle is for the IEC line cord (included) that provides AC power to the unit.

34

Never break off the ground pin on any equipment. It is provided for your safety.

If the outlet used does not have a ground pin, a suitable grounding adapter should be used and the third wire should be grounded properly. To prevent the risk of shock or fire hazard, always be sure that the mixer and all associated equipment is properly grounded.

Note for UK only

If the colors of the wires in the mains lead of this unit do not correspond with the colored markings identifying the terminals in your plug, proceed as follows: (1) The wire that is colored green and yellow must be connected to the terminal that is marked by the letter E, the earth symbol, colored green, or colored green and yellow. (2) The wire that is colored blue must be connected to the terminal that is marked with the letter N or the color black. (3) The wire that is colored brown must be connected to the terminal that is marked with the letter L or the color red.

1111..

A C O TLLE

This u nssw ed ett provides power for auxiliary equipment with power consumption of less than 300 W.

C AU TIIO N:: This outlet is n

FFU E::

The fuse is located within the cap of the fuse holder. If the fuse fails, IT MUST BE

REPLACED WITH THE SAME TYPE AND VALUE IN ORDER TO AVOID DAMAGE TO THE

EQUIPMENT AND TO PREVENT VOIDING THE WARRANTY. If the amp repeatedly blows the fuse, it should be taken to a qualified service center for repair.

WA RN G:: The fuse should only be replaced when the power cord has been disconnected from its power source!

P OW R S WIIT H::

This rocker switch applies mains power to the unit.

O UT UT

A direct output and transformer-isolated outputs are provided to allow proper interface between the amplifier and the loudspeaker system. The direct output allows connection diisscco nn ecctt tth e jju err between the

4-Ohm terminal and the XFMR terminal. Connect the loudspeaker system to the 4-Ohm and GND terminals. For XFMR isolated outputs, ensure jumper is connected and connect load between desired output and COM.

R EM OT E V OLLU ME CO NT RV C))::

These connections allow the use of a remote master volume control. For complete command of the volume from the remote control, the front panel Master Level

6

control (#8) must be set at its maximum “10” position. The remote volume control should be connected as shown in Fig. 1, with the clockwise terminal connected to the shield (SHD); the wiper connected to the control (C); and the counterclockwise terminal connected to the voltage (V). Using a 10 k Ohm potentiometer will provide approximately 30 dB attenuation, while using a 100 k Ohm potentiometer will provide approximately 60 dB attenuation.

CW

RVC

EXT

MUTE

V C SHD 2 1

FFiig e 11

2 0..

E XT RN ALL M UT G::

These connections provide for an external switch closure to activate the mute buses. A switch closure from terminal 1 to shield (SHD) mutes the input channels assigned to the mute 1 bus. A switch closure from terminal 2 to shield (SHD) mutes the input channels assigned to the mute 2 bus.

C HA NE 4 IIN PU

This is an electronically balanced line input on a removable connector. The input sensitivity is 100 mV. Channel 4 is always assigned to the mute 2 bus that is activated by a channel 1 input signal exceeding the mute 2 threshold voltage as set by control

#32.

C HA NE 2 IIN PU

This is an electronically balanced microphone or line input on a removable connector.

Input sensitivity is switchable between 1 mV (Mic) and 100 mV (Line) via control #19.

The microphone input has 24 V phantom power.

C HA NE 2 IIN PU SE NS VIIT Y::

This switch configures the Channel 2 Input (#18) to accept either microphone or linelevel input signals. The “In” position is Line mode, with an input sensitivity of

100 mV. The “Out” position is Mic mode, with an input sensitivity of 1 mV. In the Mic mode, 24 V phantom power is applied to the input.

Note: Do not operate this switch while unit is powered up!

C HA NE R IIN PU

This connector is wired parallel with the balanced Microphone Input (#30). Pin 2 corresponds to the MIC (+) on the removable connector.

LLO P::

In the “Out” position, this switch bypasses any external processing loop by internally connecting the Preamp Out (#22) to the Power Amp In (#23). Engaging the switch enables any external effects loop by internally disconnecting the preamp out from the power amp in. The line-level preamplifier can be used regardless of this switch setting.

7

2 2..

2 3..

2 4..

2 5..

2 6..

2 7..

2 8..

2 9..

3 0..

3 2..

P RE MP T::

This connection provides a line-level output of the post-EQ and master level mix to drive external devices such as signal processors, hearing assistance systems, and/or recording equipment.

P OW R A

This connection provides a direct input to the power amplifier with an input sensitivity of 1 Volt. Using the Preamp Out (#22) and engaging the Loop switch (#21), a signal processor(s) can be inserted between the mixer and the power amplifier.

C HA NE 4 O UT T::

This is an electronically balanced output on a removable connector. It provides a direct output of Channel 4, independent of muting and front panel control and is ideal for MOH applications.

C HA NE 4 R CA PU T JJA CK

These inputs are resistively summed to mono, and are in parallel with the removable input connector of Channel 4.

C HA NE 4 O UT UT ELL::

This control sets the level of the Channel 4 Output (#24). It adds up to 10 dB of gain to the Channel 4 input signal.

C HA NE 3 IIN PU

This is an electronically balanced line input on a removable connector. The input sensitivity is 100 mV. Channel 3 is always assigned to the mute 2 bus that is activated by a Channel 1 input signal that exceeds the mute 2 threshold voltage as set by control

#32.

C HA NE MU TE BU S A SIIG

In the “Out” position (Active), this switch assigns Channel 2 to the mute 2 bus. The mute 2 bus is activated by a Channel 1 signal exceeding the mute 2 threshold voltage as set by control #32. Engaging this switch (DEFEAT) prevents Channel 2 from being muted.

CH AN ELL 11 IIN PU SE NS VIIT Y::

In the “Out” position (MIC), this switch causes the input signal to channel 1 to be taken from the Mic screw terminals (#30), or the XLR input (#20). The input is configured to

1 mV sensitivity in this position, and 24 V phantom power is activated. When engaged

(TEL), the input is taken from the Tel screw terminals (#30), and the input sensitivity is

100 mV.

Note: Do not operate this switch while the unit is powered up!

CH AN ELL 11 IIN T::

This removable connector allows balanced microphone or telephone input. Input sensitivity is switchable between 1 mV (Mic), and 100 mV (Tel). The Mic input is electronically balanced and provides 24 V phantom power. The Tel input is transformer balanced.

C HA NE UT E B US AS SIIG

In the “Out” position (ACTIVE), this switch assigns Channel 1 to the mute 1 bus, allowing channel 1 to be muted by an input module with muting capabilities. Engaging this switch (DEFEAT) prevents channel 1 from being muted.

M UT 2 T HR SH

This control sets the level of signal in Channel 1 needed to activate the mute 2 bus.

Turning the control counterclockwise decreases the signal level needed to activate muting (increases sensitivity). Turning the control clockwise increases the necessary signal level to activate muting (decreases sensitivity). Full clockwise rotation will prevent mute 2 bus activation.

8

T ecch all S up orrtt

3

3

3..

4..

M OD E P OR T IIN PU T LLE ELL::

This control sets the level of an optional MMA ™ plug-in input module signal to the mix bus.

M OD E P OR

This space is designed to accept any MMA single-space plug-in module for input or output signals. For details, refer to the plug-in module instruction manual.

Note: When a MMA input module is used in the module port, it has the highest priority over the other inputs. Therefore, the utilized input module should be operated in the master mute mode ONLY. The muting status does not apply to an OUTPUT module.

M UT G P RIIO RIIT Y S TR CT E

The Mute 1 bus has priority and control over the Mute 2 bus. A signal that activates the muting function in the optional MMA plug-in input module with master muting capability mutes Channels 1 through 4 (Channels 1 and 2 Mute Bus Assign switches

#28 and #31 must be ACTIVE). Activity on Channel 1 will mute Channels 2 through 4 when Channel 1 signal level exceeds the Mute 2 Threshold control setting (Channel 2

Mute Bus Assign switch #28 must be ACTIVE).

If you require assistance with your new mixer/amp, you can get help from several sources. There are many technical documents, white papers, and application notes on our website. There are also brochures, data sheets, and our bi-monthly newsletter, Audio Interactive. Also on our website are message board forums that include questions and answers on all audio topics. This forum is a great way to learn more about audio, Peavey products and system design from other audio professionals around the world. You can also receive help by sending us an e-mail or posting a request on the message board. Finally, if you still cannot get the information you need, don’t hesitate to call us. Peavey has an extensive service department that provides tech support, parts, repair and extensive phone support services. They will be happy to assist you. The contact information for the Architectural Acoustics Division is shown below:

Peavey Electronics Corp.

Architectural Acoustics Division

711 A St.

Meridian, MS 39301

USA

Phone: 601-483-5376

Fax: 601-486-1678

Website: http://aa.peavey.com

W arrrra y R eg attiio n

Please take a few minutes and fill out the warranty registration card for your mixer. Although your warranty is valid without the registration, the information you provide with the form is crucial to our support group. It enables us to provide better service and customer support, and to keep you informed of new product updates. Refer to the warranty statement in the rear of this manual for details about what your warranty includes and what the limitations are.

9

alllliin g R M E arrss

This unit can be rack-mounted in a standard EIA equipment rack with the two included rack ears.

To attach the ears, simply remove the three screws already in the front of each side of the unit and align the ears with the appropriate mounting holes. It may be desirable to remove the rubber feet from the bottom of the unit in rack-mount installations. The ears may also be turned

90˚ to mount on the bottom or top of a shelf or for wall mounting. See figures below for alternate rack ear mounting.

Note: To provide adequate ventilation, leave at least one rack space between units when multiple amplifiers are mounted in the same equipment rack.

FFiig e 2

10

S pe attiio nss

R atte d o uttp utt p ow

UMA ™ 1502: 150 Watts

UMA 752: 75 Watts

UMA 352: 35 Watts

O uttp utt rre gu

Direct out: <0.5 dB

Transformer out: <1.0 dB

FFrre qu nccy essp on

Power Amplifier: ±0.5 dB, 20 Hz to 20 kHz,

Preamplifier: direct out

±1.0 dB, 50 Hz to 20 kHz, transformer out

±1.0 dB, 20 Hz to 20 kHz

T D::

Power Amplifier: 0.05% (1 kHz)

Preamplifier: 0.10% with nominal gain settings

P ow err b nd wiid

Direct out: <10 Hz to 70 kHz

Transformer out: 30 Hz to 40 kHz

Siig na e::

(22 Hz — 22 kHz) typical

All controls CCW:

All controls nominal (5):

-100 dB

-90 dB

Level controls CCW and master level CW: -80 dB

O uttp

Direct out:

XFMR:

Ch. 4 out:

Pre out:

IIn uttss::

Channel 1:

4 Ohms (25 V in UMA 1502)

Balanced 8 Ohms (25 V in UMA 752),

70 V, 100 V

1 V nom., +21 dBu max. at 100 Ohms

1 V nom.; +21 dBu max., at 100 Ohms

Channel 2:

Channel 3:

Channel 4:

Power in:

Mic 1 mV at 1.8 k Ohms

(XLR or screw terminals)

Tel 100 mV at 20 k Ohms

(Screw terminals)

Mic 1 mV at 1.8 k Ohms

(Screw terminals)

Line 100 mV at 20 k Ohms

(Screw terminals)

Line 100 mV at 20 k Ohms

(Screw terminals)

Line 100 mV at 20 k Ohms

(Screw terminals)

Stereo 316 mV (-10 dBV) at 4.0 k Ohms

(RCA jacks)

1 Volt at 20 k Ohms

T on e cco ollss::

Bass:

Treble:

±10 dB at 100 Hz

±10 dB at 10 kHz

FFrro ntt p ne nttrro d iin diicca

Channel 1 level control

Channel 2 level control

Channel 3 level control

Channel 4 level control

Bass control

Treble control

Master level control

Input channel signal level indicators:

(signal presence = green; signal peak = red)

Input channel mute status

Power amplifier signal presence indicator

SPS ™ indicator

Power on indicator

R ea an ell cco ollss::

Module input level control use with MMA input modules only

Channel 1 sensitivity switch

Channel 1 mute bus assign switch

Mute 2 threshold control

Channel 2 sensitivity switch

Channel 2 mute bus assign switch

Channel 4 output level control

Loop switch

Power switch

M uttiin

Mute 1: MMA input module overrides Ch 1 through 4

Mute 2: Ch 1 overrides Ch 2 through 4 with adjustable threshold control range from OFF to 100 mV (TEL) or

1 mV (MIC)

Otth err ffe

Remote volume control (RVC) via screw terminals

• 10 k Ohms approximately 30 dB attenuation

• 100 k Ohms approximately 60 dB attenuation

Mute 1 and mute 2 bus activation with switch contact closure via screw terminals

24 V DC phantom power on MIC inputs

P ow eq uiirre nttss::

UMA 1502 domestic: 300 Watts 120 V AC, 60 Hz

UMA 1502 export: 300 Watts, 230 V AC, 50/60 Hz

UMA 752 domestic:

UMA 752 export:

UMA 352 domestic:

180 Watts, 120 V AC, 60 Hz

180 Watts, 230 V AC, 50/60 Hz

100 Watts, 120 V AC, 60 Hz

Diim en allll m od

19" x 13.25" x 3.45" with rack ears

(483 mm x 337 mm x 88 mm)

17" x 13.25" x 3.45" without rack ears

(432 mm x 337 mm x 88 mm)

W eiig

UMA 352:

UMA 752:

UMA 1502:

C orr::

Black

20.0 lbs. (9 kg)

23.8 lbs. (11 kg)

27.1 lbs. (12 kg)

11

Diia am

N

L

G

12

W AR NT Y

Architectural Acoustics

®

PEAVEY ELECTRONICS CORPORATION LIMITED WARRANTY

Effective Date: July 1, 1998

W ha hiiss W arrrra y C errss

Your Peavey Warranty covers defects in material and workmanship in Peavey products purchased and serviced in the U.S.A. and

Canada.

W ha hiiss W y D oe ott C err

The Warranty does not cover: (1) damage caused by accident, misuse, abuse, improper installation or operation, rental, product modification or neglect; (2) damage occurring during shipment; (3) damage caused by repair or service performed by persons not authorized by Peavey; (4) products on which the serial number has been altered, defaced or removed; (5) products not purchased from an Authorized Peavey Dealer.

W ho hiiss W arrrra

This Warranty protects only the original retail purchaser of the product.

H ow ng hiiss W arrrra ntty

The Warranty begins on the date of purchase by the original retail purchaser. The duration of the Warranty is as follows:

Duration Product Category

MediaMatrix ® DPU (Excluding Frames), Cinema Processors,

Power Amplifiers, Pre-Amplifiers, Mixers,

Electronic Crossovers and Equalizers 5 years

Loudspeakers

Microphones

5 years

2 years

Frames

Speaker Components (incl. speakers, baskets, drivers, diaphragm replacement kits and passive crossovers) and all Accessories

1 year

1 year

W ha Pe avve Wiillll D o

We will repair or replace (at Peavey's discretion) products covered by warranty at no charge for labor or materials. If the product or component must be shipped to Peavey for warranty service, the consumer must pay initial shipping charges. If the repairs are covered by warranty, Peavey will pay the return shipping charges.

H ow o G ett W arrrra y S e

((11)) Take the defective item and your sales receipt or other proof of date of purchase to your Authorized Peavey Dealer or

Authorized Peavey Service Center.

OR

Meridian, MS 39301 or Peavey Canada Ltd., 95 Shields Court, Markham, Ontario, Canada L3R 9T5. Include a detailed description of the problem, together with a copy of your sales receipt or other proof of date of purchase as evidence of warranty coverage. Also provide a complete return address.

OR

3)) All MediaMatrix ® Frames needing repair, should be shipped prepaid to Peavey Electronics Corporation, International Service

Center, 412 Highway 11 & 80 East, Meridian, MS 39301 attiio n o plliie d W arrrra

ANY IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE

LIMITED IN DURATION TO THE LENGTH OF THIS WARRANTY.

Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.

ussiio nss o Da ma

PEAVEY'S LIABILITY FOR ANY DEFECTIVE PRODUCT IS LIMITED TO THE REPAIR OR REPLACEMENT OF THE PRODUCT, AT

PEAVEY'S OPTION. IF WE ELECT TO REPLACE THE PRODUCT, THE REPLACEMENT MAY BE A RECONDITIONED UNIT. PEAVEY

SHALL NOT BE LIABLE FOR DAMAGES BASED ON INCONVENIENCE, LOSS OF USE, LOST PROFITS, LOST SAVINGS, DAMAGE TO

ANY OTHER EQUIPMENT OR OTHER ITEMS AT THE SITE OF USE, OR ANY OTHER DAMAGES WHETHER INCIDENTAL, CONSEQUEN-

TIAL OR OTHERWISE, EVEN IF PEAVEY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.

This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

If you have any questions about this warranty or service received or if you need assistance in locating an Authorized Service

Center, please contact the Peavey International Service Center at (601) 483-5365 / Peavey Canada Ltd. at (905) 475-2578.

Features and specifications subject to change without notice.

13

80303002

Peavey Electronics Corporation • 711 A Street • Meridian, MS 39301

601-483-5376 • Fax 601-486-1678 • http://aa.peavey.com