Kyocera ECOSYS FS-3140MFP, ECOSYS FS-3640MFP Driver Manual

Legal Notes

Unauthorized reproduction of all or part of this guide is prohibited.

The information in this guide is subject to change without notice.

We cannot be held liable for any problems arising from the use of this product, regardless of the information herein.

Regarding Trademarks

KPDL is a trademark of Kyocera Corporation. Microsoft®, Windows®, Windows 7®, Windows Vista®, Windows XP®,

Windows Server®, Word®, and Powerpoint® are registered trademarks of Microsoft Corporation in the U.S. and/or other countries. PCL® is a trademark of Hewlett-Packard Company. TrueType® and Mac OS® are registered trademark of

Apple Inc. Adobe®, Acrobat®, Adobe Reader®, Photoshop® and PostScript® are trademarks of Adobe Systems,

Incorporated. UNIX® is a trademark in the United States and other countries, licensed exclusively through X/Open

Company Limited.

All other brand and product names herein are registered trademarks or trademarks of their respective companies.

Examples of the operations given in this guide support the Windows 7 printing environment. Essentially the same operations are used for Microsoft Windows Vista, Windows XP, Windows Server 2003, and Windows Server 2008 environments.

User Interface screen captures shown in this guide may differ depending on your printing system.

This user guide and its contents were developed for the 5.3 driver.

Models supported by the KX printer driver

FS-3040MFP+

FS-3140MFP+

FS-3540MFP

FS-3640MFP

© 2012 KYOCERA Document Solutions Inc.

Table of Contents

Chapter 1 Installation

Preparing to Install the Driver ........................................................................................................ 1-1

Selecting an Installation Method ................................................................................................... 1-2

Installing Utilities ........................................................................................................................... 1-2

Upgrading Driver Components ...................................................................................................... 1-2

Express Installation ....................................................................................................................... 1-2

Installing in Express Mode ....................................................................................................... 1-2

Custom Installation ........................................................................................................................ 1-4

Installing in Custom Mode with a Network Connection using Discover .................................... 1-4

Installing in Custom Mode with a USB Connection using Discover ......................................... 1-5

Installing in Custom Mode with a Network Connection using Custom Select .......................... 1-7

Installing in Custom Mode with a USB Connection using Custom Select ................................ 1-8

Optional Printer Components ........................................................................................................ 1-9

Installing Optional Printer Components ................................................................................... 1-9

The Add Printer Wizard ............................................................................................................... 1-10

Installing a Printer Driver in Windows 7 and Windows Vista .................................................. 1-10

Installing a Printer Driver in Windows XP .............................................................................. 1-10

Printer Driver Settings Access ..................................................................................................... 1-11

Changing the Default Driver Settings .................................................................................... 1-11

Chapter 2 Device Settings

Accessing Device Settings ............................................................................................................ 2-1

Device Options .............................................................................................................................. 2-1

Setting Device Options ............................................................................................................ 2-1

Auto Configure .............................................................................................................................. 2-1

Enabling Auto Configuration .................................................................................................... 2-2

Memory ......................................................................................................................................... 2-2

Setting the Memory ................................................................................................................. 2-2

RAM Disk ...................................................................................................................................... 2-3

Setting RAM Disk .................................................................................................................... 2-3

Administrator Settings ................................................................................................................... 2-3

General ......................................................................................................................................... 2-3

Show Quick Print Tab .............................................................................................................. 2-4

Send Count Information ........................................................................................................... 2-4

Send Application Name ........................................................................................................... 2-4

Associate Profile with Application ............................................................................................ 2-4

Password Protect Administrator Settings ................................................................................ 2-4

SNMP ...................................................................................................................................... 2-5

Lock Settings ................................................................................................................................. 2-6

Lock Settings Options .............................................................................................................. 2-7

User Login ..................................................................................................................................... 2-7

User Login Options .................................................................................................................. 2-8

Printing with User Login ........................................................................................................... 2-8

Job Accounting .............................................................................................................................. 2-9

Job Accounting Options ........................................................................................................... 2-9

Printing with Job Accounting ................................................................................................. 2-10

Printer Driver i

Policy Manager ........................................................................................................................... 2-11

Selecting Policy Manager Options ......................................................................................... 2-11

Printing with Policy Manager ................................................................................................. 2-12

User Settings ............................................................................................................................... 2-12

Identification .......................................................................................................................... 2-13

Units ...................................................................................................................................... 2-13

Language Preference ............................................................................................................ 2-13

PDL (Page Description Language) .............................................................................................. 2-13

PDL Options .......................................................................................................................... 2-14

PDF Options .......................................................................................................................... 2-16

XPS Driver .................................................................................................................................. 2-17

Compatibility Settings .................................................................................................................. 2-18

Media Source Enumeration ................................................................................................... 2-18

Ignore Application Collation ................................................................................................... 2-18

Combine Source and Media Type Lists ................................................................................. 2-19

Removing a Plug-in ..................................................................................................................... 2-19

Chapter 3 Quick Print

Quick Print Options ....................................................................................................................... 3-1

Common Printing Options ....................................................................................................... 3-1

Collate ..................................................................................................................................... 3-2

Duplex Printing ........................................................................................................................ 3-2

Multiple Pages per Sheet ........................................................................................................ 3-3

Edit Quick Print ........................................................................................................................ 3-3

Profiles .......................................................................................................................................... 3-4

Selecting a Profile .................................................................................................................... 3-4

Saving a Profile ....................................................................................................................... 3-4

Editing a Profile ....................................................................................................................... 3-5

Importing a Profile ................................................................................................................... 3-5

Exporting a Profile ................................................................................................................... 3-5

Application Based Printing ....................................................................................................... 3-6

Chapter 4 Basic

Basic Settings ............................................................................................................................... 4-1

Source and Media Types .............................................................................................................. 4-2

Print Size and Page Size ............................................................................................................... 4-2

Creating a Custom Page Size ................................................................................................. 4-3

Printing with Custom Size Pages ............................................................................................. 4-3

Duplex Printing .............................................................................................................................. 4-3

Printing in Duplex Mode .......................................................................................................... 4-4

Collate ........................................................................................................................................... 4-4

Printing Collated Documents ................................................................................................... 4-5

Quality ........................................................................................................................................... 4-5

Print Preview ................................................................................................................................. 4-5

Previewing a Print Job ............................................................................................................. 4-5

Kyocera Logo ................................................................................................................................ 4-6

Displaying Version Information ................................................................................................ 4-6

Displaying Plug-in Information ................................................................................................. 4-6

Chapter 5 Layout

Multiple Pages per Sheet .............................................................................................................. 5-1

Printing Multiple Pages per Sheet ........................................................................................... 5-1

Scaling .......................................................................................................................................... 5-2

Setting Scaling on the Page .................................................................................................... 5-2

Gutter ............................................................................................................................................ 5-2 ii User Guide

Creating a Gutter ..................................................................................................................... 5-2

Booklet .......................................................................................................................................... 5-3

Printing a Booklet .................................................................................................................... 5-3

Poster ............................................................................................................................................ 5-3

Printing a Poster ...................................................................................................................... 5-4

Chapter 6 Imaging

Print Quality and Custom Quality .................................................................................................. 6-1

Selecting Print Quality ............................................................................................................. 6-1

Selecting EcoPrint ................................................................................................................... 6-2

Half Speed Mode ..................................................................................................................... 6-2

Fonts ............................................................................................................................................. 6-2

Font Settings ........................................................................................................................... 6-3

Selecting Font Settings ............................................................................................................ 6-3

Font Substitution ..................................................................................................................... 6-3

Disable Device Fonts ............................................................................................................... 6-4

Graphics ........................................................................................................................................ 6-4

Selecting Graphics Settings .................................................................................................... 6-4

Pattern Scaling ........................................................................................................................ 6-4

Line Thinning ........................................................................................................................... 6-5

Inversion Options .................................................................................................................... 6-5

Optimization ............................................................................................................................ 6-6

CIE Option ............................................................................................................................... 6-6

Halftone Screen ....................................................................................................................... 6-6

Adjusting Grayscale ...................................................................................................................... 6-7

Text and Graphics Effects ............................................................................................................. 6-8

Chapter 7 Publishing

Cover Mode ................................................................................................................................... 7-1

Printing Covers ........................................................................................................................ 7-1

Cover Mode Options ................................................................................................................ 7-2

Choosing Cover Media ............................................................................................................ 7-5

Page Insert .................................................................................................................................... 7-5

Printing Page Inserts ............................................................................................................... 7-5

Page Insertion Options ............................................................................................................ 7-6

Transparency Interleaving ............................................................................................................. 7-7

Inserting Backing Sheets Between Transparencies ................................................................ 7-7

Chapter 8 Job

Job Storage (e-MPS) .................................................................................................................... 8-1

Job Storage (e-MPS) options .................................................................................................. 8-1

Proof and Hold .............................................................................................................................. 8-2

Printing a Proof and Hold Job .................................................................................................. 8-2

Private Print ................................................................................................................................... 8-2

Storing a Private Print Job ....................................................................................................... 8-3

Job Name ...................................................................................................................................... 8-3

Don’t Use Application Name .................................................................................................... 8-3

Overwrite Job Name ................................................................................................................ 8-3

Selecting a Job Name ............................................................................................................. 8-4

Chapter 9 Advanced

Prologue/Epilogue ......................................................................................................................... 9-1

Selecting a Prologue/Epilogue File .......................................................................................... 9-1

Editing a Prologue/Epilogue File ............................................................................................. 9-2

Deleting a Prologue/Epilogue File ........................................................................................... 9-2

Printer Driver iii

Assigning a Prologue/Epilogue File ......................................................................................... 9-2

Unassigning a Prologue/Epilogue File ..................................................................................... 9-2

Specifying the Insertion Point .................................................................................................. 9-2

Watermark .................................................................................................................................... 9-3

Adding or Editing a Watermark ................................................................................................ 9-3

Selecting Pages for Watermark ............................................................................................... 9-5

Security Watermark ....................................................................................................................... 9-5

Adding or Editing a Security Watermark .................................................................................. 9-6

Adjusting Security Watermark Calibration ............................................................................... 9-7

Selecting Pages for Security Watermark ................................................................................. 9-8

Status Monitor ............................................................................................................................... 9-8

Selecting Status Monitor Options ............................................................................................ 9-8

Setting Status Monitor Preferences ......................................................................................... 9-9

EMF Spooling .............................................................................................................................. 9-10

Selecting EMF Spooling ........................................................................................................ 9-10

Enable Client Profile .................................................................................................................... 9-10

Glossary

...................................................................................................................................................................

i iv User Guide

1 Installation

A printer driver is an application that manages communication between a printer and your computer. Once installed, the printer driver settings must be configured in the printer Properties and Printing Preferences .

Note: In Windows operating systems, you must be logged in with administrator rights to install the printer driver.

Preparing to Install the Driver

This section describes the initial steps to take before you install the printer driver, and based on your operating system, the next procedure you can follow.

In Windows 7 and Windows Vista with a USB connection, a driver installation will be made from the Microsoft Windows Update site if a certified driver is available and the system is connected to the web. We recommend you continue to install the driver from the supplied installation disc for an expanded feature set. In Windows, if the Found New Hardware Wizard dialog box appears during the installation process, click Cancel .

In Windows XP, or Windows Server 2003, if the Hardware Installation warning dialog box appears, click Continue Anyway . In Windows 7, Windows Vista, or

Windows Server 2008, if a warning dialog box appears stating Windows can't verify the publisher of this driver software , click Install this driver software anyway .

1 Turn on the computer and the printer.

2 Insert the Product Library disc into the disc drive. The main menu appears.

Note: If the Product Library fails to start after inserting it into the disc drive, use Windows Explorer to locate Setup.exe

on the local drive and double-click to open.

3 Click View License Agreement to read the license agreement.

4 Click Accept to proceed.

5 To begin the installation, click Install Software .

Note: If the Windows Security warning dialog box appears at any point during the installation process, click Install this driver software anyway .

6 The Installer appears with several installation methods displayed.

Printer Driver 1-1

Installation

Selecting an Installation Method

You can select Express Mode for a network or USB connection and the installation wizard will discover your printers. You can also select Custom

Mode for a network or USB connection and either manually select installation packages and specify utilities or let the installation wizard discover your printer.

Express Mode Installation

Installing in Express Mode on page 1-2

Custom Mode Installation

Installing in Custom Mode with a Network Connection using Discover on page 1-4

Installing in Custom Mode with a USB Connection using Discover on page 1-

5

Installing in Custom Mode with a Network Connection using Custom Select on page 1-7

Installing in Custom Mode with a USB Connection using Custom Select on page 1-8

Installing Utilities

On the Installation Method page, click Utilities to install printer utilities. You can also select utilities to install during the Custom Installation procedure.

Upgrading Driver Components

If the installation wizard detects older driver or utility components, the Software

Component Upgrade page appears.

1 Choose the component to upgrade. Click Next .

2 Confirm your upgrade settings. To start the upgrade, click Upgrade .

3 When the upgrade completes, click Next . The Installation Method page appears.

Express Installation

Express Mode applies to driver installation for a USB or network connection only. The installation wizard discovers printers that are turned on, and connected by USB or network cable. In Custom Mode , you are able to select the installation packages and specify the port.

Installing in Express Mode

This section describes the express installation procedure of the driver software in Windows operating systems.

1 Ensure that your printer and computer are turned on and connected by USB or network cable.

1-2 User Guide

Printer Driver

Installation

Note: In Windows 7 and Windows Vista with a USB connection, a driver installation will be made from the Microsoft Windows Update site if a certified driver is available and the system is connected to the web. We recommend you continue with the steps to install the KX Driver for an expanded feature set. In

Windows, if the Found New Hardware Wizard dialog box appears during the installation process, click Cancel .

Note: In Windows XP, or Windows Server 2003, if the Hardware Installation warning dialog box appears, click Continue Anyway . In Windows 7, Windows

Vista, or Windows Server 2008, if a warning dialog box appears stating

Windows can't verify the publisher of this driver software , click Install this driver software anyway .

2 On the Installation Method page, click Express Mode .

3 The Discover Printing System page opens, searching for your printing system.

If Discover finds your printing system, select your model from the list and click

Next .

If Discover does not find your printing system, a message appears. Remove and reinsert the USB or network cable, and ensure it is connected properly.

Click Refresh to retry the discovery. If the system still cannot find your printing system, contact your system administrator.

Select Use host name for port name to use a host name for the Standard

TCP/IP port. If the installation wizard still displays the IP address, contact your system administrator.

(Not available with a USB connection.)

Click Information if you want to open a dialog box with details about IP

Address, Host Name, Printer Model, Contact, Location, and Serial Number.

Click OK . Click Next .

(Not available with a USB connection.)

4 On the Printer Settings page, you can assign a name to your printing system.

Note: With a first time USB connection, the Printer Settings page does not appear.

You can also choose to share this printer with others or set this printer as the default printer. Make your selections, and then click Next .

5 On the Confirm Settings page, click Install if the settings are correct. Click

Back to correct the settings.

6 The Installation Completed page appears displaying the following driver options.

Print a test page

This selection verifies a connection with the printer and creates a print out of the installed driver components.

Enable Status Monitor

The Status Monitor displays system status messages on your computer screen during printing tasks. The Status Monitor button appears on the

Advanced tab.

Show Quick Print Tab

1-3

Installation

This selection lets you define basic print options into group profiles that can be accessed easily. The Show Quick Print tab option also appears in the

Administrator Settings in Device Settings .

Device Settings

Select the Device Settings check box to open Device Settings where you can choose installed options for your printing system. (The Device Settings check box appears only in Windows XP with a network connection.)

When the installation completes successfully, click Finish to exit the installation wizard.

A message may appear if there is a software installation failure.

Click Finish , and retry the installation. If the same message appears again, contact your system administrator.

The installation of the printer is now complete. If prompted, restart your computer.

Custom Installation

Custom Mode applies to driver installation for a USB or network connection.

The installation wizard can discover printers that are turned on, and connected by USB and network cable, or you can manually select the driver from drivers that are available. You can specify the printer port, fonts, and the utilities you want to install.

Printer drivers that ship with Windows operating systems are called minidrivers.

The minidriver is available separately for PCL and KPDL and provides basic support for your printer.

The KX XPS driver is only available for printing systems used with Windows 7,

Windows Vista, or Windows Server 2008. The XPS driver is discussed in the

Device Settings chapter. Minidriver functionality is not documented in this user guide.

Installing in Custom Mode with a Network Connection using

Discover

This section describes the custom installation procedure of the driver software in Windows operating systems using a network connection.

1 Ensure that your printer and computer are connected to a network.

2 On the Installation Method page, select Custom Mode .

3 The Discover Printing System page opens searching for your printing system.

The Discover button is automatically selected. A list of models appears. Click

Next .

If Discover does not find your printing system, a message appears. Remove and reinsert the network cable, and ensure it is connected properly. Click

Refresh to retry the discovery. If the system still cannot find your printing system, contact your system administrator.

1-4

4 On the Custom Installation page, select the driver and software packages you want to install from the Driver and Utility tabs, and clear those not intended for installation. Click Next .

If you only select software packages from the Utility tab, you will skip to the

Confirm Settings page.

User Guide

Printer Driver

Installation

5 On the Printer Settings page, you can assign a name for your printing system.

You can also choose to share this printer with others or set this printer as the default printer. Make your selections, and then click Next .

6 On the Confirm Settings page, click Install if the settings are correct. Click

Back to correct the settings.

Note: In Windows XP, or Windows Server 2003, if the Hardware Installation warning dialog box appears, click Continue Anyway . In Windows 7, Windows

Vista, or Windows Server 2008, if a warning dialog box appears stating

Windows can't verify the publisher of this driver software , click Install this driver software anyway .

7 The Installation Completed page appears displaying the following driver options.

Print a test page

This selection verifies a connection with the printer and creates a print out of the installed driver components.

Enable Status Monitor

The Status Monitor displays system status messages on your computer screen during printing tasks. The Status Monitor button appears on the

Advanced tab.

Show Quick Print Tab

This selection lets you define basic print options into group profiles that can be accessed easily. The Show Quick Print tab option also appears in the

Administrator Settings in Device Settings .

Device Settings

Select the Device Settings check box to open Device Settings where you can choose installed options for your printing system. (The Device Settings check box appears only in Windows XP.)

When the installation completes successfully, click Finish to exit the installation wizard.

A message may appear if there is a software installation failure.

Click Finish , and retry the installation. If the same message appears again, contact your system administrator.

The installation of the printer is now complete. If prompted, restart your computer.

Installing in Custom Mode with a USB Connection using Discover

This section describes the custom installation procedure of the driver software in Windows operating systems using a USB connection. With Discover , all devices available for the driver installation are found automatically. This is the recommended Custom Mode USB installation method.

1 Ensure that your printer and computer are turned on and connected using a

USB cable.

Note: In Windows 7 and Windows Vista, a driver installation will be made from the Microsoft Windows Update site if a certified driver is available and the system is connected to the web. We recommend you continue with the steps to install the KX Driver for an expanded feature set.

1-5

Installation

1-6

2 On the Installation Method page, select Custom Mode .

3 The Discover Printing System page opens, searching for your printing system. The Discover button is automatically selected.

Select your device and click Next .

If Discover does not find your printing system, a message appears. Remove and reinsert the USB cable, and ensure it is connected properly. Click Refresh to retry the discovery. If the system still cannot find your printing system, contact your system administrator.

4 On the Custom Installation page, select the driver and software packages you want to install from the Driver and Utility tabs, and clear those not intended for installation. Click Next .

If you only select software packages from the Utility tab, you will skip to the

Confirm Settings page.

5 On the Printer Settings page, you can assign a name to your printing system.

Note: With a first time USB connection, the Printer Settings page does not appear.

You can also choose to share this printer with others or set this printer as the default printer. Make your selections, and then click Next .

6 On the Confirm Settings page, click Install if the settings are correct. Click

Back to correct the settings.

Note: In Windows XP, or Windows Server 2003, if the Hardware Installation warning dialog box appears, click Continue Anyway . In Windows 7, Windows

Vista, or Windows Server 2008, if a warning dialog box appears stating

Windows can't verify the publisher of this driver software , click Install this driver software anyway .

7 The Installation Completed page appears displaying the following driver options.

Print a test page

This selection verifies a connection with the printer and creates a print out of the installed driver components.

Enable Status Monitor

The Status Monitor displays system status messages on your computer screen during printing tasks. The Status Monitor button appears on the

Advanced tab.

Show Quick Print Tab

This selection lets you define basic print options into group profiles that can be accessed easily. The Show Quick Print tab option also appears in the

Administrator Settings in Device Settings .

When the installation completes successfully, click Finish to exit the installation wizard.

A message may appear if there is a software installation failure.

User Guide

Printer Driver

Installation

Click Finish , and retry the installation. If the same message appears again, contact your system administrator.

The installation of the printer is now complete. If prompted, restart your computer.

Installing in Custom Mode with a Network Connection using

Custom Select

This section describes the custom installation procedure of the driver software in Windows operating systems using a network connection.

1 Ensure that your printer and computer are connected to a network.

2 On the Installation Method page, select Custom Mode .

3 The Discover Printing System page opens, searching for your printing system. The Discover button is automatically selected. Choose Custom select and click Next .

4 The Printing System page appears. Select your printing system model from the list and click Next . If there is only one driver model, this page does not appear. Proceed to the next step.

5 On the Printer Port page, select the port connected to your printing system, or add a port connected to your system by clicking Add Port . Click Next .

6 On the Custom Installation page, select the driver and software packages you want to install from the Driver and Utility tabs, and clear those not intended for installation. Click Next .

If you only select software packages from the Utility tab, you will skip to the

Confirm Settings page.

7 On the Printer Settings page, you can assign a name for your printing system.

You can also choose to share this printer with others or set this printer as the default printer. Make your selections, and then click Next .

8 On the Confirm Settings page, click Install if the settings are correct. Click

Back to correct the settings.

Note: In Windows XP, or Windows Server 2003, if the Hardware Installation warning dialog box appears, click Continue Anyway . In Windows 7, Windows

Vista, or Windows Server 2008, if a warning dialog box appears stating

Windows can't verify the publisher of this driver software , click Install this driver software anyway .

9 The Installation Completed page appears displaying the following driver options.

Print a test page

This selection verifies a connection with the printer and creates a print out of the installed driver components.

Enable Status Monitor

1-7

Installation

1-8

The Status Monitor displays system status messages on your computer screen during printing tasks. The Status Monitor button appears on the

Advanced tab.

Show Quick Print Tab

This selection lets you define basic print options into group profiles that can be accessed easily. The Show Quick Print tab option also appears in the

Administrator Settings in Device Settings .

Device Settings

Select the Device Settings check box to open Device Settings where you can choose installed options for your printing system. (The Device Settings check box appears only in Windows XP.)

When the installation completes successfully, click Finish to exit the installation wizard.

A message may appear if there is a software installation failure.

Click Finish , and retry the installation. If the same message appears again, contact your system administrator.

The installation of the printer is now complete. If prompted, restart your computer.

Installing in Custom Mode with a USB Connection using Custom

Select

This section describes the custom installation procedure of the driver software in Windows operating systems using a USB connection. With the Custom select option, you manually select the printing system and printer port to install.

In Custom mode , Custom Select is not recommended for USB in environments where printing systems are connected and reconnected using

USB ports. The Discover method provides a more reliable installation path.

1 Ensure that your printer and computer are turned on and connected using a

USB cable.

Note: In Windows 7 and Windows Vista, a driver installation will be made from the Microsoft Windows Update site if a certified driver is available and the system is connected to the web. We recommend the Custom Mode using

Discover for USB connections to ensure a reliable installation.

2 On the Installation Method page, select Custom Mode .

3 The Discover Printing System page opens, searching for your printing system. The Discover button is automatically selected. Choose Custom select and click Next .

4 The Printing System page appears. Select your printing system model from the list and click Next .

5 On the Printer Port page, select an existing port connected to your printing system. Click Next .

6 On the Custom Installation page, select the driver and software packages you want to install from the Driver and Utility tabs, and clear those not intended for installation. Click Next .

User Guide

Installation

If you only select software packages from the Utility tab, you will skip to the

Confirm Settings page.

7 On the Printer Settings page, you can assign a name to your printing system.

You can also choose to share this printer with others or set this printer as the default printer. Make your selections, and then click Next .

8 On the Confirm Settings page, click Install if the settings are correct. Click

Back to correct the settings.

Note: In Windows XP, or Windows Server 2003, if the Hardware Installation warning dialog box appears, click Continue Anyway . In Windows 7, Windows

Vista, or Windows Server 2008, if a warning dialog box appears stating

Windows can't verify the publisher of this driver software , click Install this driver software anyway .

9 The Installation Completed page appears displaying the following driver options.

Print a test page

This selection verifies a connection with the printer and creates a print out of the installed driver components.

Enable Status Monitor

The Status Monitor displays system status messages on your computer screen during printing tasks. The Status Monitor button appears on the

Advanced tab.

Show Quick Print Tab

This selection lets you define basic print options into group profiles that can be accessed easily. The Show Quick Print tab option also appears in the

Administrator Settings in Device Settings .

When the installation completes successfully, click Finish to exit the installation wizard.

A message may appear if there is a software installation failure.

Click Finish , and retry the installation. If the same message appears again, contact your system administrator.

The installation of the printer is now complete. If prompted, restart your computer.

Optional Printer Components

You can expand the functionality of your printer driver by installing optional components.

Installing Optional Printer Components

1 On the Product Library disc menu > Advanced Tools menu, select Optional

Printer Components .

2 Select a printer to install optional components, and click Next .

3 On all Select pages, choose your components, and click Next .

Printer Driver 1-9

Installation

4 On the Confirm Settings page, click Install if the displayed settings are correct. Click Back to correct any settings.

5 The Printer Components Installation Completed page appears. Click Finish .

When you have completed installing printers and optional components, restart your computer if prompted.

The Add Printer Wizard

The Add Printer Wizard displays a series of pages that guide you through printer installation. You are prompted to make installation choices on each page.

Installing a Printer Driver in Windows 7 and Windows Vista

This section describes how to install a printer driver using the Add Printer

Wizard in Windows 7 and Windows Vista.

1 Click Start and click Devices and Printers (Windows 7), or click Control Panel and double-click Printers (Windows Vista).

2 Click Add a printer .

3 The Add Printer Wizard appears. Click either Add a local printer or Add a network, wireless or Bluetooth printer . Follow the instructions on each page, and then click Next to proceed to the next page.

Note: If a warning dialog box appears stating Windows can't verify the publisher of this driver software , click Install this driver software anyway .

1-10

4 The last page of the wizard appears with a message that you’ve successfully added the printer you selected. Installation of the printer driver is now complete.

Click Print a test page if you want to produce sample print output from the newly installed printer. To close the Add Printer Wizard , click Finish .

Installing a Printer Driver in Windows XP

This section describes how to install a printer driver using the Add Printer

Wizard in Windows XP.

1 Click Start and Printers and Faxes .

2 Click Add a printer .

3 The Add Printer Wizard appears. Follow the instructions on each page, and then click Next to proceed to the next page.

Note: If the Found New Hardware Wizard page appears, click Cancel . If the

Hardware Installation warning dialog box appears, click Continue Anyway .

4 When the Completing the Add Printer Wizard page appears, installation of the printer driver is now complete. To close the Add Printer Wizard , click

Finish . If prompted, restart your computer.

User Guide

Installation

Printer Driver Settings Access

The printer driver software can be accessed from the Print dialog box of an application, or from Start . If accessed from an application, then changes made to driver settings remain in effect until the application ends. If accessed from

Start , changes are maintained as the default printer settings.

Changing the Default Driver Settings

Default driver settings apply to print jobs initiated from any application, but they are overwritten by setting changes made within each application.

1 Click Start and click Devices and Printers (Windows 7), or click Control Panel and double-click Printers (Windows Vista and Windows Server 2008), or

Printers and Faxes (Windows XP and Windows Server 2003).

2 Right-click on your printing system icon.

3 Click Printing Preferences .

4 In the Printing Preferences dialog box, select the desired features in all tabs.

5 Click OK to save the settings.

Printer Driver 1-11

2 Device Settings

In Device Settings , you can select installed printing system options so the associated features can be used with the printer driver. You can also match the memory setting in the driver with the memory installed in your printing system, which lets the driver manage font downloads more efficiently. Administrator,

User, PDL (Page Description Language), and Compatibility settings can also be selected.

Accessing Device Settings

You can open Device Settings from any of the most commonly used Windows operating systems.

1 Click Start and click Devices and Printers (Windows 7), or click Control Panel and double-click Printers (Windows Vista and Windows Server 2008), or

Printers and Faxes (Windows XP and Windows Server 2003).

2 Right-click the desired printing system model.

3 Click Printer properties (Windows 7) or Properties (Windows Vista, Windows

Server 2008, Windows XP and Windows Server 2003).

4 Click Device Settings .

Device Options

Optional devices extend the capabilities of your printing system for source, finishing, and job storage.

In a client/server environment, this feature is unavailable to a client logged in as a restricted user.

Setting Device Options

You can set the printer driver to match the optional devices installed on your printing system.

1 In Device Settings > Device options , select the check boxes for all installed devices.

2 Click OK in the Properties dialog box.

Auto Configure

Auto Configure detects the devices installed on the printing system if it is connected over a network.

Auto Configure can detect printing system devices such as input devices. When your computer is connected to the printing system

2-1 User Guide

Device Settings through a TCP/IP or WSD port, the Auto Configure button appears in Device

Settings .

Auto Configure varies by operating system, see Enabling Auto

Configuration for details.

Not all installed devices are detected by using Auto Configure . Before selecting OK in Device Settings , check the settings to make sure that they are correct.

Note: The default setting for Windows XP Service Pack 2 is for the Windows

Firewall to be set to On . The setting can be changed to allow communication between the printing system and your computer. In the Windows Security

Alert dialog box, click Unblock .

Silent Auto Configuration

Silent auto configuration checks the printing system every 10 minutes for changes in optional devices or memory. When a change is detected, the driver is automatically updated with the new settings.

Silent auto configuration is only available for printing systems installed in Windows 7, Windows Vista or

Windows Server 2008.

In a client/server environment, this feature is unavailable to a client logged in as a restricted user.

Enabling Auto Configuration

The Auto Configure button can be used to detect all available device options when the printing system is connected to a network through a TCP/IP port.

1 Verify that all optional devices are attached to the printing system, and that it is turned on and ready to print.

2 In Device Settings , click Auto Configure .

In Windows XP, the driver settings are updated immediately.

In Windows 7, Windows Vista, and Windows Server 2008, the Auto Configure dialog box opens. Select from Auto configure options:

Auto Configure Now

Click the button at any time to retrieve the current settings from the printing system. It is recommended to do this when the driver is first installed and when Silent auto configuration is turned off.

Silent auto configuration

Select to let the driver check the printing system every 10 minutes for any changes in optional devices or memory. When a change is detected, the driver is automatically updated with the new settings.

Memory

Printer Driver

Memory is the amount of standard and optional memory installed in the printing system. To maximize the downloading of printing system fonts, the driver must be set to match the total printing system memory.

Setting the Memory

By default, the Memory setting matches the standard memory in the printing system. If optional memory is installed, set the memory in the printer driver to match the total amount of memory.

2-2

Device Settings

1 Install optional DIMM memory in the printing system.

2 In Device Settings > Memory , type or select the amount of total installed memory by clicking the up and down arrows until the text box shows the correct number of megabytes (MB).

If your printing system includes the Auto Configure feature, you can use it to obtain information about the memory size.

RAM Disk

The RAM disk functions as a virtual hard disk, saving print requests into the printing system’s memory. Because the RAM disk is temporary memory, all data stored there is lost when the power is turned off.

In a client/server environment, this feature is unavailable to a client logged in as a restricted user.

Note: For some models, RAM disk requires optional printing system memory.

Once installed, set the RAM disk in Device Settings > Device options .

If selected, the Ignore application collation feature in the Compatibility

Settings dialog box lets the driver control collation. RAM disk can then increase the print speed of collated multiple copies by sending the print job just once.

Setting RAM Disk

You can set the RAM disk to save print requests into the printing system’s memory.

1 At the printing system's operation panel, turn on RAM disk and set its size.

2 In Device Settings > Device options , select RAM disk .

3 In the RAM disk text box, type or select the desired RAM disk size. Click the up and down arrows until the text box shows the correct number of megabytes

(MB) available physically on the operation panel.

The maximum RAM disk size depends on the amount of installed memory.

Administrator Settings

Administrator Settings lets you set options that include controlling accessibility, displaying features in the interface and setting a password to control access to the Administrator Settings options. Selections vary according to printing system model.

In a client/server environment, this feature is unavailable to a client logged in as a restricted user.

General

An administrator can control the display of the Quick Print tab, and other miscellaneous settings, including password and SNMP settings.

2-3 User Guide

Printer Driver

Device Settings

Show Quick Print Tab

This option lets you control the display of the Quick Print tab. You can define basic print options into group profiles for improved accessibility.

With a cleared check box for Show Quick Print tab , the tab does not appear in the Printing Preferences dialog box.

To enable this feature, in Device Settings > Administrator Settings >

General , select Show Quick Print tab .

With a selected check box for the Show Quick Print tab , the tab appears in the

Printing Preferences dialog box. When you select the Show Quick Print tab check box, you can access additional check boxes:

Hide other tabs displays only the Quick Print tab to the user.

Set Quick Print tab as default opens to this tab when you access Printing

Preferences .

Hide Edit Quick Print control prevents users from customizing the Quick

Print tab.

Send Count Information

This option lets you embed count information in the print job, which can be used by some applications for accounting purposes. Count information includes the number of copies produced as well as duplex printing, multiple pages per sheet, color mode, color page count, and paper size values.

When PDF is selected in the PDL settings dialog box, only color page count information is sent with PDF.

To enable this feature, in Device Settings > Administrator Settings >

General , select Send Count information .

Send Application Name

This option lets you send the application name with a print job, so that a different printing process is used for each application.

This option is unavailable if PDF is selected in the PDL Settings dialog box.

To enable this feature, in Device Settings > Administrator Settings >

General , select Send Application name .

Associate Profile with Application

This option lets you set all printing from each installed application to use the same driver settings as defined in a profile. Before using this feature:

A profile must be created in the Profiles dialog box, accessed from any

Printing Preferences tab.

An association must be created between a profile and an application in the

Application Based Printing dialog box, accessed from the Profiles dialog box.

To enable this feature, in Device Settings > Administrator Settings >

General , select Associate Profile with application .

Password Protect Administrator Settings

You can set Password protect administrator settings in the Administrator

Settings dialog box to prevent unauthorized changes in this dialog box. If selected, this setting prompts you to enter a password and confirm the

2-4

Device Settings password. This password protection blocks access to all Administrator

Settings options.

Setting the Administrator Password

You can set a password to prevent unauthorized changes in the Administrator

Settings dialog box.

1 In Device Settings > Administrator > General , select Password protect administrator settings .

2 In the Password dialog box, enter a password, using at least 4 and no more than 16 characters. Reenter the password in Confirm password and click OK .

Clearing the Administrator Password

You can remove the administrator password.

1 In Device Settings , click Administrator .

2 In the Enter Password text box, type the password and click OK .

3 In the Administrator Settings dialog box, clear the Password protect administrator settings check box and click OK .

SNMP

Simple Network Management Protocol (SNMP) is a set of rules that govern the management of network devices, such as printing systems. These settings determine the level of security when using the Auto Configure feature, and prevent unauthorized printing to the SNMPv3 printing system. SNMP settings must be set in the printer driver and in the printing system’s Command Center .

The following options are available:

SNMPv1/v2c

This option ensures successful Auto Configure communication using Read community name and Write community name .

SNMPv3

This option ensures secure Auto Configure communication using a user name and password. Authentication and privacy options are available by selecting Settings .

Apply to other models

This option displays a list of installed printing systems to apply the selected settings.

SNMPv3 Options

You can select options for secure communication with the printing system.

Authentication

This option provides an algorithm to check that a transferred file has arrived intact. Message Digest 5 ( MD5 ) and Secure Hash Algorithm 1 ( SHA1 ) are hash algorithms used to authenticate packet data.

MD5

2-5 User Guide

Lock Settings

Device Settings

This option provides a cryptographic hash function with a 128 bit hash value.

It adds security and protection against Gateway Load Balancing Protocol

(GLBP)-spoofing software.

SHA1

This option produces a message digest that is 160 bits long.

SHA1 is the successor to MD5 .

Privacy

This option uses encryption for secure communication. It is available after you select the Authentication option. You may select one Privacy option.

DES

This option uses the Data Encryption Standard for encryption.

DES turns cleartext into ciphertext via an encryption algorithm. It encrypts and decrypts data using 8-byte blocks and a 56-bit key.

AES

This option uses the Advanced Encryption Standard for encryption.

AES is a symmetric block cipher that can process data blocks of 128 bits, using cipher keys with lengths of 128, 192, and 256 bits. It is more secure than DES .

Selecting SNMP Settings

These settings in the driver must be set to match the settings in the printing system’s Command Center .

1 In Device Settings > Administrator > General , click SNMP Settings .

2 Select SNMPv1/v2c or SNMPv3 .

For SNMPv1/v2c , type the Read community name and Write community name , to a maximum of 32 characters, and click OK .

For SNMPv3 , type a User name to a maximum of 32 characters, and a

Password from 8 to 32 characters.

3 To set authentication and privacy options for SNMPv3 , click Settings .

4 In the dialog box, select from the available options.

5 Click OK .

6 Optional: Under Apply to other models , you can select all or any available models. You can also click Select All or Clear All . The SNMP settings are applied to all selected models.

Printer Driver

An administrator can specify settings at the tab or feature level in the driver, and then lock them. The settings are then applied to all print jobs, and changes are restricted. The settings are locked in Device Settings > Administrator

Settings > Lock Settings . For example, a driver setting could be set for printing duplex documents. This would save paper, resulting in cost savings and ecological benefits.

Locking a setting will also lock the feature where it appears in other tabs. For example, selecting Lock Multiple pages per sheet will also select and lock that feature in the Quick Print and Layout tabs.

2-6

Device Settings

User Login

The administrator can also set a password that is required to temporarily unlock a feature.

In a client/server environment, this feature is unavailable to a client logged in as a restricted user.

Lock Settings Options

The Lock Settings tab displays driver settings that an administrator can lock.

Once locked, user changes are restricted and the settings are applied to all print jobs. Once the settings are made, the Password settings option can be accessed. This lets an administrator control usage of paper and toner amounts:

EcoPrint

This option locks the EcoPrint setting.

Duplex

This option locks the current Print on both sides setting selected in the

Quick Print or Basic tab.

Multiple pages per sheet

This option locks the current Multiple pages per sheet setting selected in the Quick Print or Layout tab. The Pages per sheet option is not locked.

Clicking the icon in the Quick Print tab, or the selection in the Layout tab, switches between the two-page and four-page options. In the Layout tab, all options are available and not limited to two-page and four page.

Profile with application

This option locks a defined profile of driver settings by application.

Job tab

This option locks settings selected in the Job tab.

Security settings

This option locks the Security Watermark in the Advanced tab.

Security

Watermark is an optional plug-in.

Password settings

The password set by the administrator temporarily unlocks driver features. It prompts the user for a password. When the administrator sets the password, the Unlock button appears in the driver tabs or the Application Based

Printing dialog box. To unlock a feature, click Unlock and type the password.

2-7

User login provides job restriction by user, in contrast to the Job accounting feature, which assigns privileges by division or department. A maximum of 20 login user names and passwords can be registered at the printing system and

100 User IDs and passwords can be stored in the printer driver for use with multiple printing systems.

User login adds users with a user name and password . The user name can be in user principal name (UPN) format: [email protected]. The UPN format supports multiple domains. The UPN format is not needed if the default domain registered in the device is used.

This feature limits printing privileges to specified users for secure printing and accounting. The number of pages printed by each user will be tracked by the printing system.

User Guide

Printer Driver

Device Settings

Users added in the printer driver must also be manually registered at the printing system’s operation panel.

User Login Options

User login settings selected in the driver are applied to every print job sent from your computer.

Use specific name

This option can be used to specify a name and password to use the same

User login for every print job. If this option is selected, the user does not have to type the name and password for each print job.

A client computer in a client/server environment can accept the default name and password set by the administrator or type another name and password.

Clicking Reset restores the default values.

Prompt for name

This option prompts the user for a name and password. You can use a name that is not on the list, and the name is not added to the list. When sending a print job, type a name and password when prompted, then click OK to print.

Prompt for name and validate

This option prompts for a name and password. For the job to print, the name and password entered must be on the Login user name list. You can use the Login user names entered in the Login user name list of the driver.

When sending a print job, type a name and password when prompted, then click OK to print. This option ensures that the job prints, only after verifying that the selected name is saved in the driver.

Validate user name (computer) or prompt for login user name

This option searches for the Windows User name in the driver’s Login user name list. Validation is done every time the user prints a job. If the Windows

User name exists in the Login user name list, the associated driver Login user name and password from the list are used for the print job. To release the print job, the user must enter the Login user name and password at the printing system operation panel.

If a match is not found, the driver checks for administrator or user permissions. With user permissions, the print job is canceled, and the user is prompted to contact an administrator to establish printing permissions. With administrator permissions, the driver prompts for the Login user name and password. Along with the Windows User name , these are then added to the list so succeeding print jobs do not require the user to enter a Login user name and password again.

Login User Name

Click to add, delete, edit, import, or export login user names and passwords.

Once a Login user name list is created, the list can be exported as a group by saving it as a text file (.CSV, .KXC., and .TXT). To import a Login user name list, browse for an existing list and save it in your printer driver.

Printing with User Login

After login user names are assigned and user login mode is set to On at the printing system, you can choose User login to print in user login mode.

In a client/server environment, the client computer is automatically set to the

User login selection made in the server.

1 In Device Settings > Administrator Settings > User Login , select User

Login .

2-8

Device Settings

2 Select a User Login option:

Use specific name

Prompt for name

The remaining User Login options become available when you create a login user name list.

Note: If you select the Use specific name or Prompt for name option, proceed to step 5.

3 Under the Login user name list, click the buttons to add, delete, edit, import or export names in the list.

4 Select from the remaining User Login options:

Prompt for name and validate

Validate user name (computer) or prompt for login user name

5 Click OK in all dialog boxes.

6 Print the document from the application.

7 When the Print Options dialog box appears, type or select a name and password and click OK . Login is required for some options.

Job Accounting

Job accounting gives an administrator the ability to control usage of a printing system. With Job accounting , an administrator can assign account IDs

(identification numbers) to users or departments, a specific account ID, or make account ID input mandatory for printing. After account IDs are created, you can view from the printing system operation panel the number of copies associated with a specific ID as well as limit the number of copies for individual IDs.

Account IDs can be up to 8 digits.

Note: Job accounting must be set to On at the printing system. A maximum of 20 account ID user names and passwords can be registered at the printing system and 100 account IDs and passwords can be stored in the printer driver for use with multiple printing systems.

Job Accounting Options

Job accounting supports the following options:

Use specific account ID

Select this option to track the print jobs of a user or group with an account ID.

It sends the account ID with each print job. An administrator can restrict a user or group from changing their account ID by using the Password protect administrator settings in the Administrator Settings dialog box.

A client computer in a client/server environment can accept the default account ID set by the administrator or type another account ID. Clicking

Reset restores the default values.

Prompt for account ID

2-9 User Guide

Printer Driver

Device Settings

Select this option to track the print jobs of a user or group with an account ID as well as prompt for an account ID. At the time a print job is sent, the user is prompted to enter a Job accounting ID.

Prompt for account ID and validate

Select this option to prompt for an account ID that is saved in the driver.

When sending a print job, type an account ID when prompted, and then click

OK to print. The account ID is validated against the account ID list. If typed incorrectly, you are prompted to type it again.

Display account ID list

Select this option to display the account ID list at the time of printing. The print job can be assigned to a user or group. The account ID list is stored in the driver and more than one ID must be established for the list to appear.

Account IDs

Add, edit, or delete account IDs from the list stored in the driver. Account ID descriptions match the user or group with an account ID. After an account ID list is created, the list can be exported as a group by saving it as a text file

(.CSV, .KXC, .TXT). To import an account ID list, browse for an existing list and open it.

Printing with Job Accounting

After account IDs are assigned and Job accounting is set to On at the printing system, the number of pages printed is added to the selected account ID total.

In a client/server environment, the client computer is automatically set to the

Job accounting selection made in the server.

1 In Device Settings > Administrator Settings > Job Accounting , select Job accounting .

2 Select a Job Accounting option:

Use specific account ID

Prompt for account ID

The remaining Job accounting options become available when you create an account ID list.

Note: If you select the Use specific account ID or Prompt for account ID option, continue to step 5.

3 Under the Account IDs list, click the buttons to add, delete, edit, import, or export Account IDs in the list.

4 Select from the remaining Job accounting options:

Prompt for account ID and validate

Display account ID list

5 Click OK in all dialog boxes.

6 Print the document from the application.

2-10

Device Settings

7 For some options, when the Print Options dialog box appears, type or select an account ID, and click OK .

Policy Manager

Policy Manager is a server-based application that provides centralized user authentication, authorization, user access control, and secure pull printing features. The Policy Manager application must be installed separately. It is also necessary to make settings in the printer driver Device Settings >

Administrator > Policy Manager to integrate with Policy Manager. This Policy

Manager driver feature is installed as an optional component of the driver.

The XPS driver does not support Policy Manager. For more information about

Policy Manager, please contact your printing system dealer.

An administrator can set the Policy Manager server and user information for users and groups to print according to defined policies.

When policies restrict printing features, Policy Manager reconfigures the printer driver so that the restricted printing features are unavailable to the user or group. The Policy Manager options let you choose how conflicts are handled between a policy and a driver selection.

Secure pull printing lets the user choose a printing system after the job is sent.

To use the secure pull printing feature, the driver must be connected to the

Policy Manager spooler server using the Policy Manager spooler port. Print jobs are held in the Policy Manager spooler server until the user is authenticated at the printing system.

For a restricted user in a client/server environment, the Administrator button in

Device Settings becomes the Identity button. A user can select Policy

Manager options in the Identity Settings dialog box.

Selecting Policy Manager Options

After Policy Manager is installed and the server is set up, you can use the printer driver’s Policy Manager tab to set server and user information.

1 In Device Settings > Administrator Settings > Policy Manager , select Policy

Manager .

2 Enter the server address and port number.

3 Select an authentication option:

Use Windows authentication

Select to use Windows login information for Policy Manager authentication.

The Policy Manager Login dialog box does not appear during printing unless Windows authentication fails. If selected, continue to step 5.

Use specific name

Select to enter specific login information. When selected, continue to step 4.

4 Type the Login user name and Password . The Login user name can be in the user principal name (UPN) format to support multiple domains: [email protected]

If left blank, the Windows login user name is used.

2-11 User Guide

Device Settings

User Settings

5 You can select No notification message for policy conflicts if you do not want a message to appear when policy conflicts occur during printing. When selected, choose a printing result:

Continue printing

Applies the policy and prints the job

Cancel printing

Cancels the print job

6 A restricted user in a client/server environment can click Reset to change the

Login user name to the server’s Policy Manager user name.

7 Click OK in all dialog boxes.

Printing with Policy Manager

With Policy Manager set to on in the driver, you can send a private and secure print job.

1 Print the document from the application. You can click Preferences or

Properties to open the Properties dialog box and view printing restrictions set by the policy.

2 If the Policy Manager Login dialog box appears, enter a Login user name and password. This dialog box is generated when an invalid or blank Policy

Manager user name or password is set in the driver. The Policy Manager

Login dialog box does not appear if Use Windows authentication is selected in Administrator Settings > Policy Manager , except when the Windows authentication fails.

3 You can click Do not ask again to use the most recently-saved Login user name and password for each print job. When selected, the Policy Manager

Login dialog box does not appear again.

4 Click Log in to send the print job to the Policy Manager spooler server, where the Login user name and password are authenticated. Otherwise you can print directly to the printing system instead of using the Policy Manager spooler.

The print job appears in the Spooler folder in Policy Manager or in Client

Viewer . Please refer to the Policy Manager User Guide for Policy Manager and

Client Viewer details.

5 On the printing system’s operation panel, enter the Login user name and password to print all jobs under the Login user name. You can print from any printing system managed by the Policy Manager server.

User Settings lets you specify user and department names, select the default unit of measure, and change the driver display language.

In a client/server environment, this feature is unavailable to a client logged in as a restricted user.

Printer Driver 2-12

Device Settings

Identification

Identification lets you identify your print job with a User name and

Department information, to a maximum of 31 characters. They can appear in the Operation panel message , or User name can be used to identify a print job stored on RAM disk memory.

Setting User Identification

You can type User name and Department information.

1 In Device Settings > User , type your preferred name in the User name text box.

2 Type your department or group name in the Department text box.

You can type up to 31 characters in the User name and Department text boxes.

3 Click OK in the User Settings and Properties dialog box.

Units

You can set Inches or Millimeters as the unit of measurement. This is used for the following settings:

Custom page size setting in the Page Sizes dialog box in the Basic tab.

Spacing setting in the Add Watermark and Edit Watermark dialog boxes in the Advanced tab.

Poster settings and Gutter settings in the Layout tab.

Selecting a Unit of Measurement

You can select a unit for displaying measurements in the user interface.

1 In Device Settings > User Settings , select Inches or Millimeters .

2 Click OK in the User Settings and Properties dialog boxes.

Language Preference

The Language preference option specifies the user interface language of

Device Settings in Properties and all tabs of Printing Preferences .

Available languages vary depending on your locale and your computer settings.

Setting Language Preference

You can select a user interface language.

1 In Device Settings > User Settings , select the desired language from the

Select language list.

2 Click OK in the User Settings and Properties dialog boxes.

PDL (Page Description Language)

A Page Description Language (PDL) specifies the contents and layout of a printed page. In Device Settings , you can choose from PCL XL , (Printer

2-13 User Guide

Printer Driver

Device Settings

Command Language XL), PCL 5e , KPDL (an emulation of PostScript printing), or PDF (Portable Document Format). The printer default is PCL XL , which is suitable for most printing purposes. When using the XPS driver in Windows 7,

Windows Vista, or Windows Server 2008, XPS is the only PDL selection. After you select a PDL , the selection appears in the lower corner of the Preview image .

In GDI compatible mode , vector graphics are rasterized for printing as bitmap images. Use the GDI compatible mode option to improve the output quality of the graphic created by the application.

Note: To add PDF to the list of PDL choices, you must install the Output to

PDF plug-in.

In a client/server environment, this feature is unavailable to a client logged in as a restricted user.

PDL Options

The PDL options, available in the PDL Settings dialog box, are accessed in

Device Settings .

PCL XL

The most recent version of HP PCL and PCL 6. This PDL includes PCL 5e features. PCL XL lacks backward compatibility with earlier PCL versions, though it is enhanced over PCL 5e in these areas:

Reduced file size

Better print speed

Faster return to application

PCL 5e

Fully compatible with earlier PCL versions

Bidirectional communication support

Wide selection of fonts for use with Microsoft Windows applications

Complex graphics might not print as well

KPDL

KPDL is used when printing from applications that support PostScript 2 or 3.

An emulation of PostScript printing

Strong graphics reproduction

Print speeds may be slower than PCL 5e

Requires more printing system memory than PCL 5e

Enables native TrueType font downloading

Supports most Graphics settings options

PDF

Output to PDF is a plug-in feature that lets you print and save documents from multiple sources to Adobe PDF. This feature can be used as an alternative to existing commercial applications for creating PDF documents. Documents saved as PDF retain their original appearance, and can be viewed and printed with Adobe Reader on Windows, Mac OS, and UNIX platforms.

For a document using mixed paper sizes, all pages in the PDF use the size of the first page.

2-14

Device Settings

2-15

Note: With PDF selected in the PDL Settings dialog box, only a limited set of driver options are available.

PDL Settings

When you click the Settings button, the available options are:

PCL XL Settings or KPDL Settings

Enable smart duplex printing

This option automatically keeps a sheet of paper from being sent through the duplex unit if the sheet will only be printed on one side. The duplex unit will be bypassed for the following types of print jobs: a one page document, one page from a multi-page document, or a multi-page document that prints onto a single sheet. Selecting this option can reduce wear on the mechanical duplex unit, and result in comparatively faster printing times.

PCL XL Settings

Skip printing blank pages

This option prevents the printing system from outputting any page that contains no data, or that has, at most, one space character. Selecting this option can save paper, and result in comparatively faster printing times. This feature is for regular printing (not for booklet, duplex or multiple pages per sheet).

KPDL Settings

Allow data passthrough

This option reduces errors when printing complex jobs from applications that use PostScript formatting. When selected, EMF spooling is not available in the Advanced tab.

PDF Settings

Provides options for printing and saving documents to Adobe PDF format.

See PDF topics for details.

Selecting a PDL

You can select a page description language from PDL options.

1 In Device Settings > PDL > PDL Settings , select the desired page description language from the Select PDL list.

2 You can select the GDI compatible mode option to improve the output quality of graphics created by your application.

3 Select Settings when the PDL is set to PCL XL , KPDL or PDF .

If you select PCL XL , you can select Skip printing blank pages and Enable smart duplex printing .

If you select KPDL , you can select Allow data passthrough and Enable smart duplex printing .

If you select PDF , you can select from the available PDF Settings.

4 Click OK in the PDL Settings and Properties dialog boxes.

User Guide

Printer Driver

Device Settings

PDF Options

You can select PDF options if you have installed the Output to PDF plug-in.

The PDF Settings dialog box contains the following options:

PDF Settings

Embed fonts

This option ensures that document fonts appear accurately in the PDF file on screen. This option ensures accurate reproduction but significantly increases the file size.

Compress data

This option enables flat compression for the generated PDF document. This option significantly reduces the file size. Additional compression options are available within Adobe Acrobat.

Security

This option applies encryption to the PDF document. Click Settings for additional Security settings. See the next section for details.

Print and save

This option lets you print and save a document as a PDF file. Click Settings for additional Print and save settings.

Security Settings

This option lets you select an encryption level and create passwords for the generated PDF file.

The following security options are available:

Encryption

Encryption provides password protection so that a document cannot be opened or altered by unauthorized users.

40 bit

This encryption option provides low level security for a PDF document. It is supported for Adobe Acrobat and Adobe Reader 6.0, or later.

128 bit

This encryption option provides high level security for a PDF document. It is supported for Adobe Acrobat and Adobe Reader 6.0, or later.

Passwords

Select passwords for changing security settings and for opening a document. Passwords are supported up to 16 characters in length.

Require password to change security settings

Type an Owner password . Within Adobe Acrobat, this password is required to change the document restrictions in the Files > Properties > Security section. When a document with this password is opened in Adobe Reader, it cannot be printed or edited, and document data cannot be copied.

Require password to open document

Type a User password . The user password must be entered at the time the

PDF document is opened. This password must be different from the owner password.

Print and Save Settings

This option lets you print and save a document as a PDF file.

2-16

Device Settings

XPS Driver

Save to file only

A PDF file is created and saved locally.

Save to file and print

A PDF file is created, saved locally, and sent to print.

After you select between these two options, you can choose the following option:

Automatically save to default file

A PDF file can be saved automatically as a default file to be used again.

You can then select from the following options:

Replace default file

This option replaces an existing file having the default file name KxPdf.pdf.

Use default file + date and time

This option lets you use the default file name and add a date and time stamp each time the document is saved.

Default file directory

This option lets you browse to a location to save your PDF.

Printing and Saving to PDF

You can print a document and save it to Adobe PDF, if you have installed the

Output to PDF plug-in.

1 In Device Settings > PDL Settings , in the Select PDL list select PDF .

2 Click Settings .

3 In the PDF Settings dialog box, select Print and save .

4 Click Settings , and select from print and save options. See the PDF Options topic for details.

5 Click OK in all dialog boxes.

6 Open and print the document.

7 Name and save the PDF file.

In Windows 7, Windows Vista, and Windows Server 2008, the XML Paper

Specification ( XPS ) Page description language provides the most efficient method for displaying, processing, and printing documents. As both a PDL and a document format, XPS requires compatible printer hardware and software written for the Windows Presentation Foundation (WPF) architecture.

PCL and

KPDL are not compatible with an XPS environment. Therefore, an XPS driver supports a single PDL setting. The XPS driver can be installed from the

Product Library disc. In the Installation Method menu, click Custom Mode , and on the Custom Installation page, select KX XPS DRIVER .

2-17 User Guide

Device Settings

To view a print to file XPS document, download and install the Microsoft XPS

Viewer.

Compatibility Settings

Compatibility Settings lets you specify media source values, override the application's Collate setting, and combine the Source and Media type lists in the Basic tab.

In a client/server environment, this feature is unavailable to a client logged in as a restricted user.

Media Source Enumeration

Media source enumeration supports compatibility for media source values unique to the printer driver, such as those for cassettes or feeders. Your newly installed printer driver maintains identical media source support with the driver it replaces, whether for this driver or one from another manufacturer. If media source macros exist for the older driver, then the alignment of media source values maintains support without the need to change the macros.

Setting Media Sources

Use the Driver Info utility (\Utility\Driver Info\DrvInfo.exe) to compare the source values for all installed drivers.

If the values for a given media source differ between printer drivers, you can reassign an enumerated value to create a match between the drivers.

1 In Device Settings > Compatibility Settings , from the Media source enumeration list select the paper supply method. The current value is listed in the Enumerated value box.

2 Type an Enumerated value for the media source, and click Apply . To align settings with a different driver, this value should align with those in the other driver.

3 Click OK in the Compatibility Settings and Properties dialog boxes.

You can restore all the options in Compatibility Settings to the default by clicking Reset .

Ignore Application Collation

This option bypasses the Collate setting in software applications, and gives priority to the printer driver setting.

With the check box selected, the printer driver Collate setting is used.

With the check box cleared, the application Collate setting is used.

Selecting Printer Driver Collation

You can ignore the collation setting in the application and use the printer driver collation setting.

1 In Device Settings > Compatibility Settings , select Ignore application collation .

2 Click OK in the Compatibility Settings and Properties dialog boxes.

Printer Driver 2-18

Device Settings

You can restore all the options in Compatibility Settings to the default by clicking Reset .

Combine Source and Media Type Lists

You can change the driver's Basic tab so that Media type and Source are combined into one list, labeled Source . In the combined list, Media types are listed first, followed by cassettes and MP tray .

Creating a Combined Source List

You can combine the Source and Media type lists in the Basic tab to make one Source list.

1 In Device Settings > Compatibility Settings , select Combine source and media type lists .

2 Click OK in the Compatibility Settings and Properties dialog boxes.

You can restore all the options in Compatibility Settings to the default by clicking Reset .

Removing a Plug-in

You can remove an installed plug-in from the driver. If removed, the plug-in features do not appear in the driver interface.

Note: To remove the Output to PDF module, PDF must not be selected in the PDL Settings dialog box.

1 In Device Settings , click Kyocera logo > Plug-in .

2 Select a plug-in module from the list and click Delete , then Yes .

3 Click OK in all dialog boxes.

2-19 User Guide

3 Quick Print

In the Quick Print tab, you can apply basic print settings to print jobs. Any

Quick Print settings can be saved as a group, called a profile, and applied to any print job. Profiles support common printing tasks.

The administrator can set the view of the Quick Print tab through the

Installation process, or in Device Settings > Administrator > General .

This chapter can be used as a separate Quick Print user guide when KX Driver support is controlled by an administrator.

To return to the original settings, click Reset . The Reset button is available when accessing the printer driver from the application's Print dialog box.

Quick Print Options

You can set one or more print options on the Quick Print tab. You can create your own customized view of print options with Edit Quick Print . And you can also select from profiles that have been set with predefined options for frequently run print jobs.

Common Printing Options

The upper section of the Quick Print tab has several icons that represent the most common options for print jobs. Click on the Quick Print icons to change settings for the print job. Some of these options also appear on the Basic ,

Layout , and Imaging tabs.

A maximum of five icons can appear in the Quick Print tab. You can change or remove icons from the display.

Orientation

Printer Driver 3-1

Quick Print

3-2

This icon changes between portrait, landscape, portrait rotated, landscape rotated printing formats.

Collate

This icon changes the ordering of the printed pages. The page ordering sequence can either be 123, 123, or 111, 222 and so on.

Print on both sides

This icon changes between duplex printing for flipping on the long edge, duplex printing for flipping on the short edge, or for not using duplex printing.

Multiple pages per sheet

This icon changes between Off, 2, and 4 for the number of pages printed on one sheet. For more than 4 pages per sheet, define these settings in Layout

> Multiple pages per sheet .

EcoPrint

This icon changes the text and graphics to appear lighter in the printed job.

EcoPrint does not increase print speed.

Edit Quick Print

This button lets you select the print option icons to display and in what order when you access the Quick Print tab. The Edit Quick Print button is not available when the driver is accessed from an application’s Print dialog box.

Any basic print options can be Reset to the default values in the Quick Print tab. This button only appears when it is accessed from an application’s Print dialog box.

The following sections describe some of the Quick Print tab options in more detail.

Collate , Duplex printing , and EcoPrint can also be found in the Basic and Imaging tabs, and Multiple pages per sheet in the Layout tab. The

Profiles options are accessed from Printing Preferences .

Collate

Collate specifies the order in which the pages of a multiple copy job are printed.

With Collate selected, the first time the print job is sent to the printing system the data is rendered as page images in the printing system's memory. The remaining job copies are printed from the stored data. This avoids the extra processing involved in sending every copy from the computer to the printing system.

With Collate selected, the driver prints the complete job set by set. With Collate cleared, it prints each page by set. For example, with Collate selected, three copies of a five-page document output as pages one through five in succession, three times.

The printer driver automatically overrides the application’s Collate setting and uses the printer driver setting. You can use the application's Collate setting by clearing the Ignore application collation check box in the Compatibility

Settings dialog box accessed from Device Settings .

Duplex Printing

Duplex printing is printing on both sides of each page. Select Print on both sides to start duplex printing. The printing system contains a duplex unit that turns the paper over to allow printing on the reverse side.

Print on both sides must be selected to print on both sides of the cover and insert pages.

Flip on long edge

Turn the long edge of the page to view the content.

User Guide

Printer Driver

Quick Print

Flip on short edge

Turn the short edge of the page to view the content.

Multiple Pages per Sheet

Multiple pages per sheet prints several pages on a single sheet of paper for the purpose of reviewing the document and conserving paper. The size and readability of the multiple pages decrease as the number of pages per sheet is increased. You can set the arrangement of the pages from the Layout tab as well as print borders around each of the pages.

When Multiple pages per sheet is selected, Scaling and Poster are unavailable.

Edit Quick Print

The assortment of icons at the top of the Quick Print tab can be customized to include features that you use most often. Any number of icons from 0 to 5 can be displayed. All icons can be removed from view if you want to use only the

Profiles options in the Quick Print tab.

Note: An administrator can hide the Edit Quick Print button by selecting

Hide Edit Quick Print control in Device Settings > Administrator Settings .

The Edit Quick Print button is unavailable when the driver is accessed from an application’s Print dialog box.

Editing Quick Print Options

You can select from a limited set of driver features to appear in the Quick Print tab.

1 Click Start and click Devices and Printers (Windows 7), or click Control Panel and double-click Printers (Windows Vista and Windows Server 2008), or

Printers and Faxes (Windows XP and Windows Server 2003).

2 Right-click on the desired printing system model and click Printing

Preferences .

3 Select the Quick Print tab.

4 Click Edit Quick Print .

To add a feature to the Quick Print tab, select the feature under Available controls , and click the right arrow to move the feature to Selected controls .

A maximum of 5 features can appear under Selected controls .

To remove a feature from the Quick Print tab, select the feature under

Selected controls , and click the left arrow to move the feature to Available controls . To use only the Profiles in the Quick Print tab, move all features to Available controls .

Click the up and down arrows to change the position of the features under

Selected controls . The feature at the top appears on the left in the Quick

Print tab.

To restore the list to factory default options, click Reset .

5 After making your selections, click OK .

3-3

Quick Print

Profiles

3-4

In Profiles , you can save printer driver settings as a profile. You can select multiple options in any Printing Preferences tabs, save them as a profile, and use all of them at once when you apply the profile. The profiles list always includes a Factory Default profile that returns the driver options to their default settings. The profiles can include Common Profiles , which are installed as optional components through the Optional Printer Components , and any custom profiles created. A maximum of 26 profiles can be established in one driver, including the Factory Default profile. Settings made in Device Settings cannot be saved to a profile.

Selecting a Profile

You can select and apply a profile from the Quick Print tab or from the Profiles dialog box.

Quick Print tab

1 In the Quick Print tab, select a Profile . The side panel displays a summary of the settings. Above the settings you can click the icons to choose between images of tone adjustment, the printing system, or page layout.

2 Click Apply .

Profiles dialog box

1 In any of the Printing Preferences tabs, click Profiles .

2 In the Profiles dialog box, select a profile. The dialog box displays a summary of the settings for that profile.

3 Click Apply .

4 Click OK .

Saving a Profile

The Save button lets you create your own profiles. You can select the printing options you want in the driver, then save the driver settings including your customizations as a profile. You can then use that profile to print the same type of print job again without having to reselect all the settings. In Printing

Preferences , the Profiles button appears at the bottom of all the tabs.

1 Set the printing options you want for your print job by opening Printing

Preferences and selecting all your driver settings.

2 Click Profiles > Save .

3 To identify the profile, type a Name , select an Icon , and type a Description .

4 Click OK to save the profile.

The newly added profile appears in the Profiles dialog box.

User Guide

Printer Driver

Quick Print

5 Click Apply to use the selected profile for the current print job, or click OK to close the dialog box.

Note: To reset the printer driver to default settings, select the Factory Default profile, and click Apply . This clears the settings of a selected profile.

You can remove a profile by selecting it in the Select profile list and clicking

Delete .

Editing a Profile

The Edit button lets you make changes to an existing profile. The Factory

Default profile cannot be edited.

1 Click Profiles .

2 In the Select profile section, select the profile to be edited, and click Edit .

3 Any of the three options can be edited: name, icon and description. Click OK to save the edited changes.

The newly edited profile appears in the Profiles dialog box.

4 Click Apply to activate the selected profile to the current print job, or click OK to close the dialog box.

Importing a Profile

The Import button lets you import a copy of a profile from other printer drivers into your printer driver.

1 Click Profiles > Import .

2 Browse for the existing profile (.KXP), select it, and click Open .

A message appears if any of the profile settings in the imported file are unavailable in the existing driver. Select Yes , to import the profile, or No , to cancel the import.

3 If you selected Yes in the previous step, the newly imported file appears in the

Profile dialog box.

4 Click Apply to use the selected profile for the current print job, or click OK to close the dialog box.

Exporting a Profile

The Export button lets you export a copy of a profile from your printer driver for use in other printer drivers. The Factory Default profile cannot be exported.

1 Click Profiles .

2 In the Select profile section, select the profile to be exported, and click Export .

3-5

Quick Print

3-6

3 In the Export Profile dialog box, name and save the profile.

4 Click OK to close the Profiles dialog box.

Application Based Printing

An administrator can associate a profile with an application so that all printing from the application uses the same profile settings. This makes profiles easier to use and ensures consistent printing from an application. For example, a duplex printing profile can be applied to all spreadsheet printing to save paper.

Associations between profiles and applications can be created at any time in the

Profiles dialog box. To use the associations in printing, you must select

Associate Profile with application in Device Settings > Administrator >

General .

A maximum of 25 associations can be created in the Application Based

Printing dialog box, accessed from the Profiles dialog box.

In a client/server environment, a user on a client computer can view details about server associations but cannot change settings or select another profile.

Adding an Association

Once profiles have been created or imported, you can create an association between a profile and an application. Then the application always prints using the associated profile settings.

1 In any tab, click Profiles to open the Profiles dialog box.

2 Click Application to open the Application Based Printing dialog box.

3 Click Add to open the Add Association dialog box.

4 Enter a name for the association, to a maximum of 31 characters.

5 Under File name , enter a valid executable file name (.EXE) for an application that allows printing, or browse to find a file located on your computer.

6 Select a profile from the list.

7 Click OK in the Add Association and Application Based Printing dialog boxes to create the association.

You can remove an association by selecting it and clicking Delete .

Editing an Association

You can change the name, file, and profile for an association.

1 In any tab, click Profiles to open the Profiles dialog box.

2 Click Application to open the Application Based Printing dialog box.

3 Select an association to edit and click Edit to open the Edit Association dialog box.

User Guide

Quick Print

4 Change desired settings under Association name , File name , or Profile .

5 Click OK in the Edit Association and Application Based Printing dialog boxes to save the revised association.

Printer Driver 3-7

4 Basic

In the Basic tab, you can specify the most commonly used printer driver settings.

To return to the original settings, click Reset . The Reset button is available when accessing the printer driver from the application's Print dialog box.

Basic Settings

4-1

The Basic tab contains several settings for the most commonly used printing tasks.

Print size

This setting sets the size of the area that the printer prints to, regardless of the actual paper size that is used by the printing system.

Source

This setting specifies the cassette or tray that the printing system draws paper from. Unless you are using a custom paper type, you can leave it set to Auto source selection .

Page Sizes

This setting should match the page size setting in your application. The printing result is based on the page size specified in this setting. You can also create a custom page size.

Media type

This setting selects the Source based on the types of media that are specified in the printing system. In general, you can leave it set to

Unspecified .

User Guide

Basic

Destination

This setting specifies which output tray is used for the print job output.

Orientation

These settings specify the paper orientation of the print job. If Rotated is selected, the print job orientation is rotated 180 degrees.

Copies

This setting specifies the number of copies to print. For collating multiple copies, select Collate .

Duplex

These settings enable printing on both sides of a sheet of paper.

Quality

This EcoPrint check box makes the entire image, text and graphics, appear lighter in the printed job. This setting does not increase print speed.

Print Preview

This setting lets you view your document before printing.

Note: Some applications may override print settings made in the driver.

Usually the application can be set to follow the settings. In Microsoft Word

2007, ensure that Default tray in Options is set to Use printer settings .

Source and Media Types

In the Basic tab, Source specifies which tray or cassette the printer uses for a printing job. The default is Auto source selection , which instructs the printer to search for the media requested by the application or the printer driver. If the selected tray or cassette empties during a print job, then the printer searches for another source, and continues the job.

Media type instructs the printer to search for the type of paper or media that is requested by the application or the printer driver. The choices shown may change depending on the selection in Source . If Auto media selection is selected, then the printer searches for another tray or cassette using the same media.

Transparencies, labels, envelopes, and cardstock must be supplied from the

MP tray . Ensure the paper is properly loaded by following the instructions outlined in the printing system's Operation Guide .

Note: Source and Media type are separate items in the dialog box, but can be combined using the Combine source and media type lists setting in

Compatibility Settings . If they are combined, Media type is not available on the Basic tab. To change this setting, open Device Settings > Compatibility

Settings and clear the Combine source and media type lists selection.

Print Size and Page Size

Print size controls the output page size of the document. To use this setting, ensure that the Page Sizes setting matches the page size setting in your application. If the Print size is different from the page size in your application, then each page is enlarged or reduced to match the Print size . The percentage value shown in brackets indicates the size of the Print size setting relative to the Page Sizes setting. If the Page Sizes does not match the page size setting in the application (the size of the original) then, in most cases the Print size is ignored and the document is printed based on its original size.

Printer Driver 4-2

Basic

You can create a page size with your chosen dimensions for printing on nonstandard size paper. For example, you can create a custom banner with a height from 5.82 inches (148.0 mm) to 14.01 inches (356.0 mm) and a width from 2.75 inches (70.0 mm) to 8.5 inches (216.0 mm). You can then save the custom setting to the Page Sizes and Print size lists for later selection.

Creating a Custom Page Size

To use custom page sizes, they must be created and added to the Print size list. The driver supports a maximum of twenty custom sizes.

1 In the Basic tab, click Page Sizes .

2 Click New .

3 A default custom name appears in the Name box. Type a name for your custom page size.

4 Type or select values for the height and width. If the height or width value exceeds the allowable limit, it automatically adjusts to the limit after Apply or

OK is clicked.

5 When done, click Apply .

The custom page size appears in the Print size list, which is used for enlarging and reducing the sizes of prints.

To delete a custom page size from the Page Sizes dialog box, select the name of the custom page size and click Delete .

Printing with Custom Size Pages

You can print on custom-sized pages.

1 Load custom-sized paper into the MP tray.

2 In the Basic tab, select the name of your custom page size in the Print size list.

3 Click OK to return to the Print dialog box.

4 Click OK to start printing.

Duplex Printing

Duplex printing is printing on both sides of each page. Select Print on both sides to start duplex printing. If it is not selected, then the printer prints on only one side of each page. The printer system contains a duplex unit that turns the paper over to allow printing on the reverse side.

Print on both sides must be selected to print on both sides of the cover and insert pages.

Flip on long edge

Turn the long edge of the page to view the content.

Flip on short edge

Turn the short edge of the page to view the content.

4-3 User Guide

Basic

Flip on long edge

Flip on short edge

Collate

Printer Driver

Printing in Duplex Mode

You can print on both sides of each page.

1 In the Basic tab, select Print on both sides .

2 Select either Flip on long edge or Flip on short edge .

3 Click OK to return to the Print dialog box.

4 Click OK to start printing.

Collate specifies the order in which the pages of a multiple copy job are printed.

With Collate selected, the first time the print job is sent to the printing system the data is rendered as page images in the printing system's memory. The remaining job copies are printed from the stored data. This avoids the extra processing involved in sending every copy from the computer to the printing system.

With Collate selected, the driver prints the complete job set by set. With Collate cleared, it prints each page by set. For example, with Collate selected, three copies of a five-page document output as pages one through five in succession, three times.

4-4

Basic

The printer driver automatically overrides the application’s Collate setting and uses the printer driver setting. You can use the application's Collate setting by clearing the Ignore application collation check box in the Compatibility

Settings dialog box accessed from Device Settings .

Printing Collated Documents

When printing multiple copies of a multiple page document, the printer can assemble the pages of each copy in numerical order.

1 In the Basic tab, select the Collate check box.

2 Type or select the number of complete sets of the print job in the Copies box.

The document page count must not exceed the printer tray capacity.

3 Click OK to return to the Print dialog box.

4 Click OK to start printing.

Quality

The Quality feature, EcoPrint , changes toner saturation in the printed job, making the entire print image, including text and graphics, appear lighter. The amount of toner varies based upon your printing system model and the type of data printed (text, graphics, or both).

EcoPrint is also available in the Quick

Print and Imaging tabs.

To enable this feature in the Basic tab, select the EcoPrint check box.

Print Preview

After selecting driver settings, you can use Print preview to check the print job before you proceed with printing. If you are satisfied with the preview, you can print. Or you can cancel printing if you want to change driver settings.

Previewing a Print Job

You can see a print preview before printing.

1 Select desired driver settings in all tabs, or select a profile.

2 In the Basic tab, select Print preview .

3 Click OK in the Printing Preferences and Print dialog boxes.

4 When the Print preview dialog box appears:

Click the arrow buttons to view document pages.

To close the preview and make additional changes in driver settings before printing, click the “X” button.

If you are satisfied with the preview, click the printer button to print the job.

4-5 User Guide

Basic

Kyocera Logo

The Kyocera logo appears on the bottom portion of any Printing Preferences screen or Device Settings screen. Click the logo to open the About dialog box that displays the driver version number and driver plug-in information.

Displaying Version Information

In Device Settings or any tab, click Kyocera logo > Version to view the following driver information:

File Name

Version

Description

Date

Manufacturer

Comments

To view copyright information, click Legal Notices .

Click OK to close the driver information dialog boxes.

Displaying Plug-in Information

A plug-in integrates with the printer driver to extend the driver’s capabilities.

In Device Settings or any tab, click Kyocera logo > Plug-in to view the following plug-in information:

Module

Description

Version

Click OK to close the driver information dialog boxes.

Printer Driver 4-6

5 Layout

In the Layout tab, you can arrange document data on printed pages without affecting the original document.

To return to the original settings, click Reset . The Reset button is available when accessing the printer driver from the application's Print dialog box.

Multiple Pages per Sheet

Multiple pages per sheet prints several pages on a single sheet of paper for the purpose of reviewing the document and conserving paper. The size and readability of the multiple pages decrease as the number of pages per sheet is increased. You can set the arrangement of the pages from the Layout tab as well as print borders around each of the pages.

When Multiple pages per sheet is selected, Scaling and Poster are unavailable.

Printing Multiple Pages per Sheet

You can print several pages on a single sheet of paper.

1 In the Layout tab, select Multiple pages per sheet .

2 In Pages per sheet , select the number of pages to print on each sheet of paper.

3 If you want to print a border around each page, select Print borders .

5-1 User Guide

Scaling

Gutter

Layout

4 In the Layout list, select the direction the pages should flow.

5 Click OK to return to the Print dialog box.

6 Click OK to start printing.

Scaling increases or decreases text and graphics on a page. You can also select a gutter setting that enlarges the margins to accommodate manual stapling or manual hole punch.

Scaling is unavailable when other Layout tab options are selected.

Setting Scaling on the Page

You can increase or decrease text and graphics on a page.

1 In the Layout tab, type or select a scaling percentage between 20 to 500.

Scaling adjusts proportionately the height and width of the page. A lower percentage reduces the page and a higher percentage enlarges the page.

2 Click OK to return to the Print dialog box.

3 Click OK to start printing.

Gutter increases the margins around your text and graphics on the left side and at the top of the printed sheet.

Gutter is often used for binding, hole punch, or stapling to make a print job easier to read. This creates a larger margin space by shifting the printable area to the right, or down, as much as one inch (25.4

mm).

Creating a Gutter

You can increase the margins on the left side and at the top of the printed sheet.

1 In the Layout tab, click Gutter .

2 In the Gutter width options, type or select a value between 0.20 to 1.00 inches

(5.0 to 25.4 mm).

Short edge (top)

This selection modifies the outside margin on the top-edge of the page.

Long edge (left)

This selection modifies the outside margin on the left-side of the page.

Note: Availability of Gutter settings varies depending on Orientation and

Duplex settings in the Basic tab.

Printer Driver 5-2

Layout

Booklet

Poster

5-3

3 If text extends too close to the edge of the page, select Reduce image to fit .

The text appears slightly reduced and away from the edge of the page. If text does not extend beyond the page when the gutter increases, clear Reduce image to fit .

4 Click OK to save gutter settings, then click OK again to return to the Print dialog box.

5 Click OK to start printing.

Booklet prints a two-page layout on both sides of each sheet of paper. You can fold and bind the booklet in the center. Folded booklets are half the size of the selected paper.

When Booklet is selected, other Layout tab options are unavailable.

A different paper source can be selected for the booklet cover. To include a cover on the booklet, select the Publishing tab, then select Cover mode .

Printing a Booklet

You can print a booklet.

1 In the Layout tab, select Booklet , and one of the two binding options.

Left edge binding

This selection prints text that reads from left to right.

Right edge binding

This selection prints text that reads from right to left.

2 Click OK to return to the Print dialog box.

3 Click OK to start printing.

The Poster feature lets you create a document to a size that is larger than the paper your printer can support. You can print a poster, or banner, up to 25 times larger than the original document. Segments of the poster document are printed on several sheets of paper and with the assistance of poster settings, you can reassemble the sheets easily to create a poster.

Use Sheets per page to select the poster size in relation to the original document size. Each option shows the number of sheets to be printed and the maximum poster size.

When Poster is selected, other Layout tab options are unavailable.

Note: Sheets per page displays the unit of measurement in inches or millimeters. You can change the Units setting in the User Settings dialog box, accessed from Device Settings .

Use Print format to print a proof sheet, along with the poster, to guide you in assembling the printed poster sheets.

User Guide

Printer Driver

Layout

Poster pages

This selection prints all of the sheets to be assembled as a poster.

Proof sheet

This selection prints all the poster pages on one sheet with markings that display the sheet assembly.

Poster pages and proof sheet

This selection prints all poster sheets and a one-page proof sheet.

Use Poster Settings to select options, in any combination to make it easier to create a poster. These options print visual cues on the poster sheets that provide help in cropping and assembling the pages.

Overlap edges

This selection duplicates the edges of document data on adjoining sheets.

Poster appearance is improved when the edges overlap slightly. Select the check box, then type or select a value between 0.00 and 1.20 inches (0.0

and 30.4 mm). This option reduces the final poster size slightly.

Print crop marks

This selection prints a border at the edges of each poster sheet. You can crop each sheet on the border before assembling the sheets. This option ensures that data on adjoining sheets matches precisely.

Print assembly marks

This selection prints numbers at the edges of each sheet, matching numbers on adjoining sheets. Assemble each sheet edge to the same numbered edge on another sheet.

Printing a Poster

You can print a poster.

1 In the Layout tab, select Poster .

2 In Sheets per page , select the poster size. Each option describes the number of sheets it takes to represent one finished poster page.

3 Click Poster Settings to select options in any combination. These options ensure a precise assembly of the pages to create the poster.

4 In Print format , select one of the options for a finished print format.

5 Click OK to return to the Print dialog box.

6 Click OK to start printing.

5-4

6 Imaging

In the Imaging tab, you can manage print quality and grayscale settings.

To return to the original settings, click Reset . The Reset button is available when accessing the printer driver from the application's Print dialog box.

Print Quality and Custom Quality

Print quality lets you set the resolution for the print job. Resolution is a measurement, in dots per linear inch (dpi), that describes the sharpness and clarity of printed text and images.

Custom Quality lets you set a more refined resolution for the print job.

Half speed mode lets you reduce print speed to improve printing on small or thick paper.

Selecting Print Quality

In the Imaging tab, select a Print quality from the list. The number of selections in Print quality depends on the number of resolutions supported by the printing system.

High quality , Proof , Draft

Select one of these settings to print from the highest to the lowest print resolution.

Proof is unavailable when PCL 5e is selected in the PDL

Settings dialog box.

Custom

Custom lets you choose a setting for Custom Quality and EcoPrint .

Click Custom Quality to open a settings dialog box with selections for a more refined resolution. Depending on your model, Resolution can be set to

6-1 User Guide

Fonts

Imaging

Fine 1200 , Fast 1200 (unavailable for the PCL 5e Page description language), 600 dpi , or 300 dpi .

Kyocera image refinement smoothes the edges of text and vector graphics and can be set to On , or Off .

Selecting EcoPrint

EcoPrint changes toner saturation in the printed job, making the entire print image, including text and graphics, appear lighter. The amount of toner varies based upon your printing system model and the type of data printed (text, graphics, or both).

EcoPrint does not increase print speed.

EcoPrint is also available in the Quick Print and Basic tabs.

1 In the Imaging tab, in the Print Quality list, select Custom .

2 Click EcoPrint to open the EcoPrint dialog box.

3 To start EcoPrint , select On ; to stop it, select Off .

4 Click OK to close the EcoPrint dialog box.

Half Speed Mode

Half speed mode reduces the print speed to half the rated speed. When selected, the toner adheres better when printing on small size, thick, or textured paper. This mode may result in quieter printing.

Note: Half speed mode applies to all media types except Transparency and

Vellum .

A computer font is a data file containing a set of glyphs (visual representations of textual elements), characters, or symbols. Common terms for fonts are:

Outline fonts , in contrast to bitmap fonts, are defined as a set of mathematical lines and curves. An outline font is more easily scalable

(designed to display and print clearly at any point size) than a bitmap font.

Bitmap fonts define each character as a pattern of pixels (the smallest resolvable rectangular areas of an image). Such fonts are not easily scalable and distort when reduced or enlarged.

Native fonts are the basic or original fonts installed with the computer operating system. TrueType fonts are the native fonts used by Microsoft

Windows.

TrueType fonts are a type of scalable outline fonts. TrueType has long been the most common format for fonts on Microsoft Windows.

System fonts are the primary fonts used by the operating system. They are typically accessed through an application interface or through a common font dialog box.

Device fonts are stored either permanently or temporarily in the printing system memory.

Printer Driver 6-2

Imaging

6-3

Font Settings

The Font Settings dialog box lets you specify how TrueType fonts are sent to the printing system. The chosen method affects the speed and quality of the print job:

Download as outlines

This method is best suited for large documents or print jobs using multiple fonts and font sizes. Print speeds are faster because of the optimization features in this setting. The repetition of similar font data sent to the printing system is reduced, thereby increasing the print speed. Print speed is not increased when using Asian fonts such as Japanese, Chinese, and Korean, because of the large amount of font information used for these particular fonts.

Allow native download

This method improves text quality and increases print speed by converting

TrueType fonts to Adobe Type 42 font format. This feature is available when

KPDL is selected in the PDL Settings dialog box.

Download as bitmaps

Downloading fonts as bitmaps provides more detail, however it creates large file sizes. This is best suited for print jobs with custom fonts, very small fonts

(point size 1-4), or Asian fonts.

Substitute with device fonts

System fonts and device fonts are automatically matched based on typeface name. This function increases print speed and efficiency. It is useful for changing a font used throughout a large document, by replacing the old font with the desired font.

Note: GDI compatible mode does not support Substitute with device fonts .

Selecting Font Settings

You can specify how TrueType fonts are sent to the printing system.

1 In Imaging > Fonts , select one of the methods for sending TrueType fonts.

2 Click OK to return to the Print dialog box.

3 Click OK to start printing.

Font Substitution

Font substitution is the process of using one font in place of another when the intended font is not available to a printing system. Font substitution may be critical for output of documents to printing systems that are not well supported by a large font inventory.

Setting Font Substitution

You can use one font in place of another.

1 Click Start and click Devices and Printers (Windows 7), or click Control Panel and double-click Printers (Windows Vista and Windows Server 2008), or

Printers and Faxes (Windows XP and Windows Server 2003).

User Guide

Imaging

2 Right-click on the desired printing system model and click Printing

Preferences .

3 In Imaging > Fonts , select Substitute with device fonts , and then click Fonts .

In the Fonts Substitution dialog box, the System fonts list shows the fonts installed on your computer. The Available device fonts list shows the printing system fonts.

4 Select the system font, and then the available device font to be substituted.

5 Click OK to save your settings.

If the device font does not have similar font characteristics to the system font, character spacing in the document may appear incorrect.

Disable Device Fonts

In some cases, the printing system substitutes fonts even if you send the

TrueType fonts as outline fonts or bitmap images. Select Disable device fonts to prevent substitution of device fonts for TrueType fonts.

This option also improves portability of printable data. (If cleared, device fonts may not match when sent to a different printing system.)

Some Adobe applications have device font limitations. To overcome these limitations, select Disable device fonts . Device fonts are normally visible in the application font lists as printer icons next to the font name, unless there are equivalent system fonts, in which case the “TT” TrueType icon remains.

Disabling Device Fonts

You can prevent substitution of device fonts for TrueType fonts.

1 In Imaging > Fonts , select the Disable device fonts check box.

2 Click OK to save your settings.

Graphics

Printer Driver

Graphics are pictorial representations of information. Graphics can be functional

(charts, diagrams) or artistic (drawings, photographs).

Graphics Settings let you select options for your printed graphics.

Note: Some options are available only when a specific PDL is selected.

Selecting Graphics Settings

1 In the Imaging tab, click Graphics .

2 In the Graphics Settings dialog box, select from the available options, and then click OK to save your selections.

Pattern Scaling

Pattern scaling is a feature that can help improve visual compatibility between screen and print output. Graphics objects, such as a shape or a path, often

6-4

Imaging

6-5 include patterns and fills that are composed of collections of printed dots. A pattern is a planned or random repetition of colors, shapes, lines, values, and textures to create a visual arrangement. A fill is the application of a color or grayscale to a graphics object. If printed patterns and fills do not match the appearance of that on the screen, use Pattern scaling to select a different density of printed dots.

In Imaging > Graphics settings , select Pattern scaling settings.

Auto (default setting)

This setting prints patterns and fills to match the on-screen appearance.

Coarse

This setting prints patterns and fills with the fewest number of lines, patterns, or dots. Coarse is the same as Auto when PCL XL or PCL 5e is selected in the PDL Settings dialog box.

Medium

This setting prints patterns and fills with a greater number of lines, patterns or dots than the Coarse setting. Medium is the same as Auto when KPDL is selected in the PDL Settings dialog box.

Fine

This setting prints patterns and fills with the greatest number of lines, patterns, or dots. Printed patterns and fills may appear more dense than the on-screen appearance.

Line Thinning

Line thinning reduces the pen width of lines used for barcodes and line drawings. Drawing values controlled by an application are not changed.

Line thinning is available when PCL XL is selected in the PDL Settings dialog box. When GDI compatible mode is selected in the PDL Settings dialog box,

Line thinning is not available.

Off (default setting)

Line thinning is not applied.

Barcodes

This setting reduces the pen width value for vertical and horizontal lines. It improves the readability of barcodes.

Fine lines

This setting reduces the pen width value for vertical, horizontal, and diagonal lines.

All

This setting reduces the pen width by a value of 1 for vertical, horizontal, and diagonal line used in barcodes or line drawings.

Inversion Options

Inversion is the opposite of the normal order, arrangement, or position of an image or printed content.

In Imaging > Graphics Settings , select Inversion options . The settings are available when KPDL is selected in the PDL Settings dialog box.

Reverse image

This setting prints images like a photo negative, reversing black and white areas of the image.

User Guide

Printer Driver

Imaging

Mirror print

This setting prints the page content backwards, as it would appear in a mirror image.

Optimization

Optimization is a process or methodology of improving a printing system's function or effectiveness.

In Imaging > Graphics Settings , select Optimization . The settings are available when KPDL is selected in the PDL Settings dialog box.

Fast printing

This setting increases print speed and decreases spool size. It delivers images in binary format. It can be used for most everyday printing needs.

Document portability

This setting creates a PostScript file in ASCII text encoding. Unlike the binary format created in Fast printing , the ASCII text created with this selection can be edited.

CIE Option

CIE optimization bypasses the normal procedure of processing every aspect of the CIE color space used in applications such as Adobe Acrobat and

Photoshop. This feature increases print speed for documents printed from these applications by optimizing CIE data. It has no effect on print jobs that do not use

CIE data.

CIE optimization should be selected for speed not accuracy, so printed output may be different from appearance on the screen.

In Imaging > Graphics Settings , select the CIE optimization check box.

CIE optimization is available when KPDL is selected in the PDL Settings dialog box.

Halftone Screen

Halftone Screen lets an experienced user print different shades of gray as are found in photographs. Shades are produced by printing dots of various sizes and shapes, and by spacing them closer or farther apart. Shading can also be adjusted by the number of rows of data, the angle of the rows, and the shape of the data.

Halftone Screen is available when KPDL is selected in the PDL Settings dialog box. It is unavailable when GDI compatible mode is selected in the PDL

Settings dialog box.

Setting the Halftone Screen

Halftone Screen provides a means to apply shades of gray to black and white printed output.

1 In Imaging > Graphics Settings , click Halftone Screen .

2 Clear the Use printer's default screens check box.

3 Set the available options to the desired values:

Ink

Lists the halftone screens available. For black and white printers, this option appears unavailable and is permanently set to Black .

6-6

Imaging

Frequency

Displays the number of rows of dots per inch or centimeter. Set the range from 2.0 to 999.9, and select lines/inch or lines/cm.

Angle

Sets the angle at which rows are aligned. Set the range from -180 to 180 degrees.

Shape

Select the shape of the halftone dot:

Ellipse

Resists optical jump. An optical jump occurs when an area of an image suddenly become darker. An ellipse shape provides a smooth gradation of tones. Select Ellipse for images with dark areas.

Round

Resists moiré formation and dot gain. Moiré formation is an unintended pattern that occurs when two or more colors are printed at the wrong angles.

The correct angles depend on the number of colors being printed. Dot gain is when the halftone dots increase when printed, causing a moiré pattern.

Select Round for images with light tints and highlighted areas.

Line

Used for special effect. Select Line to change the effect by selecting a different angle.

4 Select Increase accuracy of screens for better print quality, possibly increasing print time.

5 Click OK to return to the Print dialog box.

6 Click OK to start printing.

Adjusting Grayscale

The grayscale adjustment settings change the Brightness and Contrast of graphics. These settings are useful if graphic images are printing too light, too gray, or too dark. Text remains unaffected.

1 In the Imaging tab, under Adjustment , select Custom .

A preview image in the Adjustment Settings dialog box illustrates any brightness and contrast changes.

2 Drag the Brightness slider right to lighten, or left to darken the graphic images of the print job.

You can also change brightness by entering a numeric value in the text box at the right. The brightest setting is +100; the darkest is -100. Zero is the default mid-level setting. Adjusting brightness is useful when graphic images are printing too dark or too light.

3 Drag the Contrast slider right or left to increase or decrease the proportion of light to dark in the graphic images of the print job.

6-7 User Guide

Imaging

A high contrast setting decreases the grayscale spectrum, making light grays lighter and dark grays darker. A low contrast setting increases the grayscale spectrum, making light grays darker and dark grays lighter.

You can also change contrast by entering a numeric value in the text box at the right. The highest contrast setting is +100; the lowest is -100. Zero is the default mid-level setting. Adjusting contrast is useful if graphic images are printing too gray, or too black and white.

4 Click OK to save your grayscale adjustment settings.

Text and Graphics Effects

Special settings are available for printing.

Print text as black

This option prints all color text as black. It produces faster printing of color text by reducing the amount of data sent to the printer. In black and white printers, it increases the detail for light-colored text printed. White text and image colors are unaffected.

Print graphics as black

This option prints all color graphics with black, rather than grayscale. This feature is intended for CAD applications.

Printer Driver 6-8

7 Publishing

In the Publishing tab, you can create covers and inserts for a print job, and add backing sheets between transparencies.

To return to the original settings, click Reset . The Reset button is available when accessing the printer driver from the application's Print dialog box.

Cover Mode

7-1

Cover mode lets you add cover pages for the front and back of your document.

You can print on cover pages of a different weight or color than the main document. The source of the cover paper is specified by adjusting the Media for cover settings in the Publishing tab.

Print on both sides must be selected in the Basic tab or Quick Print tab in order to print using the Front inside or Back outside options.

Although Cover mode and Page insert can be used simultaneously, they cannot be used with Transparency interleaving .

Printing Covers

You can choose cover pages for printing.

1 In the Publishing tab, select Cover mode .

2 Select Front or Front and back to specify the type of covers.

3 Select from Print onto options if you want to print on the covers.

User Guide

Printer Driver

4 Click OK to return to the Print dialog box.

5 Click OK to start printing.

Cover Mode Options

Check Box Selection

Front

Cover Insertion Type

Inserts a blank front cover.

Publishing

Front

Front outside

Prints on the outside surface of the front cover.

Front

Front inside

Prints on the inside surface of the front cover.

— continued

7-2

Publishing

Check Box Selection

Front

Front outside

Front inside

Cover Insertion Type

Prints on the outside and inside surfaces of the front cover.

Front and back

Inserts blank front and back covers.

Front and back

Front outside

Prints on the outside surface of the front cover and inserts a blank back cover.

7-3

Front and back

Front inside

Prints on the inside surface of the front cover and inserts a blank back cover.

— continued

User Guide

Check Box Selection

Front and back

Front outside

Front inside

Publishing

Cover Insertion Type

Prints on both sides of the front cover and inserts a blank back cover.

Front and back

Back inside

Prints on the inside surface of the back cover and inserts a blank front cover.

Front and back

Back outside

Prints on the outside surface of the back cover and inserts a blank front cover.

Printer Driver

Front and back

Back inside

Back outside

Prints on both sides of the back cover and inserts a blank front cover.

— continued

7-4

Publishing

Check Box Selection

Front and back

Front outside

Front inside

Back inside

Back outside

Cover Insertion Type

Prints on both sides of the front and back covers.

Choosing Cover Media

You can select media for the cover.

1 In the Publishing tab, select Cover mode .

2 In the Media for cover list, select the media type or source cassette for the front and back covers. When you choose the media type, a source cassette matching that media type is automatically selected.

3 Click OK to return to the Print dialog box.

4 Click OK to start printing.

Page Insert

7-5

A Page insert is a preprinted page or a page of a different paper type that is inserted at specified points in a print job. The inserted page can also be printed on during the print job. Both sides of the page insert can be printed on by using the duplex unit.

Print on both sides must be selected in the Basic tab or Quick Print tab in order to print using the Print onto back option.

Although Cover mode and Page insert can be used simultaneously, they cannot be used with Transparency interleaving .

Printing Page Inserts

Several ways are available to arrange page inserts: you can print on one or both sides or insert a blank sheet.

1 In Publishing > Page insert , select the option corresponding to your desired page arrangement.

2 To print on both the front and back of the inserted page, select the Print onto front and Print onto back check boxes.

3 In Insert before pages , type the page number to insert. A page is inserted between the page number you typed and the page before it.

User Guide

Publishing

4 From the Media for page list, select the media type of the inserted page or the source paper cassette. When you choose the media type, a source cassette matching that media type is automatically selected.

5 Click OK to return to the Print dialog box.

6 Click OK to start printing.

Page Insertion Options

Check Box Selection

Page insert

Page Insertion Type

Inserts a blank page.

Printer Driver

Page insert

Print onto front

Prints on the front side of the inserted page.

Page insert

Print onto back

Prints on the back side of the inserted page.

— continued

7-6

Publishing

Check Box Selection

Page insert

Print onto front

Print onto back

Page Insertion Type

Prints on both sides of the inserted page.

Transparency Interleaving

Transparency interleaving inserts a backing sheet between printed transparencies. The backing sheet, also known as an interleaf, helps keep transparencies clean and prevents them from clinging together. This feature is only available when printing on transparencies supplied from the MP tray . You can print the same content on the backing pages as on the transparencies.

Transparency interleaving cannot be used together with Cover mode or

Page insert .

Inserting Backing Sheets Between Transparencies

You can insert backing sheets between transparencies.

1 In Basic > Media type , select Transparency . If the Source and Media type lists have been combined (by a selection in Device Settings > Compatibility

Settings ), Media type does not appear. Instead, in the Source list select Auto

(Transparency) .

2 In Publishing , select Transparency interleaving .

3 To print the transparency content on the inserted pages also, select the Print onto backing check box.

4 In the Media for backing list, select the Media type of the backing sheet or the

Source paper cassette. When you choose the media type, a source cassette matching that media type is automatically selected.

5 Click OK to return to the Print dialog box.

6 Click OK to start printing.

The printing system's operation panel prompts you to load transparencies into the MP tray , and if necessary, load backing paper into the selected cassette.

7-7 User Guide

8 Job

In the Job tab, you can store print jobs in the memory installed in the printing system. You can also select a Job name to use with Job storage features. You can use this tab to set or change the default settings that apply when you print a document from a Microsoft Windows application.

To return to the original settings, click Reset . The Reset button is available when accessing the printer driver from the application's Print dialog box.

Job Storage (e-MPS)

Job storage (e-MPS) offers a set of options for saving print jobs in printing system memory, so that you can print or reprint them later. Print jobs can easily be reprinted later using the printing system’s operation panel, and printing of sensitive documents can be restricted to approved users.

E-MPS is a multitier solution that provides advanced print management, directly from the desktop. By storing a job in the printing system, you can print it from the operation panel without sending it again from the computer.

To use the Job storage (e-MPS) features, you can set a user name in the User

Settings dialog box, available in Device Settings . If you do not set a user name, the Windows login user name is the default.

Job Storage (e-MPS) options

Storage location Access code required

When job is printed

When job is deleted from memory

— continued

Printer Driver 8-1

Job

Proof and hold

Private print

RAM disk

RAM disk

No

Yes

One print when job When printing is sent; remaining system is turned off prints later

When access code When printing is entered at operation panel system is turned off or after printing

Note: This printing system does not support Quick copy and Job storage features.

Proof and Hold

Proof and hold is a Job storage (e-MPS) option that prints one copy of a print job so that you can proof it before printing the remaining copies. This feature is available when a RAM disk is set up in the driver and turned on at the printing system.

After the proof copy is printed and checked, remaining copies can be printed from the printing system’s operation panel without sending the job again from the computer. If desired, you can change the number of copies printed.

Note: Proof and hold is not available for some applications such as

Microsoft Excel.

All Proof and hold jobs are stored in RAM disk memory after printing but are deleted when the printing system is turned off. You can manually delete a job at the operation panel.

Warning: A print job can replace a job in RAM disk memory having the same

User name and Job name . To prevent this, select Use job name + date and time under Overwrite job name .

Printing a Proof and Hold Job

Proof and hold lets you print one copy of a multicopy job to proof before printing the remaining copies. The job is stored in RAM disk memory until the printing system is turned off or the job is manually deleted.

1 In the Basic tab, select the number of copies to be printed.

2 In the Job tab, select Job storage (e-MPS) .

3 Select Proof and hold .

4 Click OK in all dialog boxes.

Private Print

Private print jobs are saved in RAM disk memory for printing until a four-digit

Access code is entered. When the RAM disk reaches maximum capacity and a new job is sent to be stored, the oldest stored job is replaced by the new job.

Private print jobs are deleted when the printing system is reset or turned off.

When sending a sensitive document to the printing system, a user must type a four-digit access code, which is attached to the print job along with the Job

8-2 User Guide

Job name and User name . The job is not printed until a user enters the access code at the printing system’s operation panel. After the job is printed, it is removed from printing system memory.

The number of Private print jobs that can be stored is limited only by the storage capacity of the RAM disk. You can manually delete a job at the operation panel.

Warning: A print job can replace a job in RAM disk memory having the same

User name and Job name . To prevent this, select Use job name + date and time under Overwrite job name .

Storing a Private Print Job

Private print lets you store a document temporarily in printing system memory without printing, and protect it with an Access code . The job is stored in RAM disk memory until it is printed, manually deleted, or turned off.

1 In the Job tab, select Job storage (e-MPS) .

2 Select Private print .

3 In the Access code box, type four numbers if you want to restrict access to your document.

4 Click OK in all dialog boxes.

Job Name

Printer Driver

A Job name is a unique identifier for each print job. It helps you find and print your job from the printing system’s operation panel. When you send a print job using one of the Job storage (e-MPS) options, you can assign a custom name to the job or use the name of the application file.

For Microsoft Word and PowerPoint, you can choose to include or omit the application name from the application defined Job name . You can also ensure that jobs in printing system memory are not replaced by new jobs having the same Job name .

Don’t Use Application Name

Don’t use application name is an option to remove the application name from the job name in job storage features. By selecting Don’t use application name , the file name you choose appears clearly in the job list. This feature is applicable only when printing from Microsoft Word or PowerPoint.

Overwrite Job Name

Overwrite job name is an option to ensure that a saved print job is not replaced in printing system memory by a new job having the same Job name . If a user sends two print jobs with the same User name and Job name , the second job replaces the first job without any prompt. To prevent this, Overwrite job name can automatically change the Job name by adding the date and time the job is sent. This feature also helps you to track when print jobs were sent from the computer.

The selected option applies to a Job name with either Application defined or

Custom selected.

Overwrite job name options include:

8-3

Job

Replace existing file

This option lets the current print job replace an existing job in printing system memory, if a job with the same User name and Job name exists.

Use job name + date and time

This option adds the current date and time to the end of the Job name , in the format: mmddyy hhmmss

The previous print job with the same job name remains in the printing system memory.

Selecting a Job Name

You must select a job name to use with Job storage (e-MPS) features, so that you can find your job in job lists on the printing system’s operation panel. The selected job name is saved with the print job when the job is sent to printing system memory.

1 In the Job tab, select Job storage (e-MPS) .

2 Under Job name , select a name:

Application defined

This option uses the name of the application document as the job name. For

Microsoft Word or PowerPoint documents, selecting Don’t use application name removes the name of the application so that only the document name appears as the job name.

Custom

This option uses a unique name for each job. Type a name in the box, up to

79 characters.

3 Select an Overwrite job name option in case a job already exists in printing system memory with the same job name:

Replace existing file

If a job with the same user name and job name exists, the current print job replaces an existing job in printing system memory.

Use job name + date and time

This option adds the current date and time to the end of the job name, in the format: mmddyy hhmmss

The previous print job with the same job name remains in the printing system memory.

8-4 User Guide

9 Advanced

In the Advanced tab, you can choose special features that extend the capabilities of the printing system.

To return to the original settings, click Reset . The Reset button is available when accessing the printer driver from the application's Print dialog box.

Prologue/Epilogue

The Prologue/Epilogue feature lets you insert a command file at the beginning of a print job or at the end. The command file, prepared in a text editor, utilizes programming commands from the printer resident PRESCRIBE language. The

Product Library disc includes a PRESCRIBE command language reference guide. A command file is a set of instructions the printing system interprets to produce a given output. For example, a Prologue/Epilogue command file may contain a macro that places a graphic object such as a logo at the top of a letterhead document.

Selecting a Prologue/Epilogue File

A Prologue/Epilogue file must be available on your computer before it can be added to a print job. To create this file, use a text editor like Windows Notepad.

In Advanced > Prologue/Epilogue , select a Prologue/Epilogue file name to insert into the print job. (If no file names are visible in the list, you must click Add to browse for files on your computer or network to add to the list.) After the file is selected, insertion point options become available.

Printer Driver 9-1

Advanced

9-2

Editing a Prologue/Epilogue File

You can edit a Prologue/Epilogue file on your computer.

1 In Advanced > Prologue/Epilogue , select a Prologue/Epilogue file name from the list, and then click Edit .

2 After your text editor opens, make your changes to the file.

3 Save the file and exit.

Note: Editing and saving a command file replaces the contents of the existing local or network file.

Deleting a Prologue/Epilogue File

You can remove a Prologue/Epilogue file from the list.

1 In Advanced > Prologue/Epilogue , select a Prologue/Epilogue file name from the list, and then click Delete .

2 In the delete confirmation box, click Yes to accept.

Note: Only the file name is removed from the command file list. The file itself is not deleted, but remains on the network or local computer.

Assigning a Prologue/Epilogue File

You can insert a Prologue/Epilogue file into a print job.

1 In Advanced > Prologue/Epilogue , select a Prologue/Epilogue file name from the list.

2 Under Insertion Point , select a place to insert the Prologue/Epilogue file.

Unassigning a Prologue/Epilogue File

If you designate a Prologue/Epilogue file as unassigned, you are removing it from the print job. It remains in the list. Unassigned selections are useful when the list contains several Prologue/Epilogue files, and you want to use some but not others.

1 In Advanced > Prologue/Epilogue , select a Prologue/Epilogue file name from the list.

2 Under Insertion Point , select Unassigned .

Specifying the Insertion Point

The insertion point is the location in the print job where the selected

Prologue/Epilogue command file is processed by the printing system. Each file in the list can be assigned only one insertion point.

User Guide

Advanced

Note: The Start of the page and End of the page insertion point options are available only if PCL 5e is selected in the PDL Settings dialog box.

With a command file selected in the list, choose one insertion point option:

Unassigned

The selected command file is not inserted into the print job. This selection can be used when you are working with multiple command files and want to use some but not others. Select Unassigned for the command files you do not want to use in the print job.

Beginning of the print job

The command file is inserted as the first page of the print job. The document starts printing on the second page.

End of the print job

The command file is inserted as the last page of the print job, which prints after the last page of the document.

Start of the page

The command file is inserted at the top of each page of the print job.

End of the page

The command file is inserted at the bottom of each page of the print job.

Only on odd pages

If Start of the page or End of the page is selected, this option can be selected to insert the command file into all odd-numbered pages.

Only on even pages

If Start of the page or End of the page is selected, this option can be selected to insert the command file into all even-numbered pages.

Pages

If Start of the page or End of the page is selected, this option can be selected to insert the command file into specified pages. In the text box, type individual page numbers separated by commas, or a page range separated by a hyphen. For example, if you type 2 in the text box, the command file is inserted only into page 2. If you type 1, 3, 5-12 the command file is inserted into page 1, page 3, and pages 5 through 12. If the Pages option is selected and you click OK without typing any numbers, you will be prompted to specify page numbers.

Watermark

A watermark is a recognizable image or pattern that can be placed on a page or throughout a document. You can choose one of the standard watermarks or create your own text. The preview area at the left of the dialog box shows how the watermark appears on a page. This is useful for making adjustments to the appearance and location of the watermark.

Adding or Editing a Watermark

You can create a new watermark that displays your chosen text. Any watermark can be edited, though a limited number of options can be changed for default watermarks.

Printer Driver 9-3

Advanced

9-4

1 In Advanced > Watermark , click Add to create a user defined (custom) watermark; or under Select watermark , select a default or custom watermark and click Edit .

2 Under Watermark name , type a name, up to 39 characters. A default watermark cannot be renamed.

3 Under Watermark text , type your preferred text. This option is not available when editing a default watermark.

4 Select the font, style, and size of the text.

5 Select the color of the watermark from the list. The options available are black and shades of gray.

6 Select the watermark Count , to a maximum of 20. In the Spacing spin box, select the distance between two or more watermarks in tenths of an inch or in millimeters.

7 Select the Position of the watermark with one of the following options.

Centered (default)

This option places the center of the watermark text in the center of the page.

User defined

This option lets you manipulate the x and y coordinate boxes to move the text around the page.

You can also change the position by clicking the position button at the bottom of the preview area and then clicking the watermark image. Drag the pointer to move the watermark image.

8 Select the Angle of the watermark with one of the following options.

Diagonal (default)

This option places the watermark text at the default angle on the page.

User defined

This option lets you type a degree value for the angle. An angle is measured in degrees, from 0 to 360.

You can also change the angle by clicking the angle button at the bottom of the preview area. Click and hold as you drag the pointer to move the watermark image.

9 The Rotate around center check box at the bottom far right of the dialog box determines the method of rotation for the watermark. You must select User defined in both Position and Angle to enable this option. Select Rotate around center to position the watermark text with the center of the text as its axis, and clear it to position the watermark text with the left end of the text as its axis.

10 In all dialog boxes, click OK .

User Guide

Advanced

Selecting Pages for Watermark

The Page selection option for Watermark lets you choose the location for watermarks in your document.

1 In Advanced > Watermark > Select watermark , choose a default or custom watermark to print.

2 Under Page selection , choose pages for printing the watermark:

All pages

This option prints the watermark on each document page.

First page only

This option prints the watermark on the first document page.

All pages except first page

This option prints the watermark on all pages after the first page.

Only on specified pages

This option prints the watermark on page numbers typed in the box.

Print onto front outside cover

This option prints the watermark on the front cover. It is available when

Cover mode is selected in the Publishing tab. If Cover mode and Front outside are both selected in the Publishing tab, Print onto front outside cover is selected automatically.

3 In all dialog boxes, click OK .

Security Watermark

The Security Watermark is a plug-in feature that prints a nearly invisible image or text against a background pattern. The security watermark appears only when the printed page is photocopied. This helps to identify printed pages that should not be photocopied, or to distinguish between original prints and photocopies. Six standard security watermarks are available as text or image, and you can create custom security watermark text.

A notable feature of Security Watermark is the Document guard pattern , which prevents the document from being photocopied, scanned, faxed, or printed from memory. If a scan, fax, or print from memory is attempted, the process is stopped and an error message appears on the printer's operation panel.

Following installation of the printer driver, use the Optional Printer

Components wizard to install the Security Watermark plug-in.

If PCL XL is selected in the PDL Settings dialog box, Security Watermark appears in the Advanced tab

The administrator can ensure that a security watermark is printed on all jobs by selecting Device Settings > Administrator > Lock Settings > Lock Security

Settings .

Selecting Security Watermark sets these driver features to the following values:

Watermark in the Advanced tab is set to None .

Resolution in Imaging > Print Quality > Custom > Custom Quality is set to 600 dpi .

Printer Driver 9-5

Advanced

9-6

Kyocera Image Refinement in Imaging > Print Quality > Custom >

Custom Quality is set to Off .

EcoPrint in Quick Print , Basic > Quality , or Imaging > Quality is set to

Off .

Adjustment Settings ( Brightness and Contrast ) in Imaging > Grayscale

> Adjustment > Custom is set to 0 .

The reverse is also true. If these features are changed, then the Security

Watermark selection is set to None , and cannot be used.

Adding or Editing a Security Watermark

You can create a new security watermark that displays text but not an image.

Any security watermark can be edited, though a limited number of options can be changed for default security watermarks.

1 In the Advanced tab, click Security Watermark .

2 In the Security Watermark dialog box, click Add , to create a new security watermark; or under Select security watermark , select a default or custom security watermark and click Edit .

3 For Security watermark name , type a name up to 39 characters. A default security watermark cannot be renamed.

4 For Security watermark text , type text or leave blank. This option is not available when editing a default security watermark. Select from the following options:

None

This option leaves the line blank.

User defined

This option inserts your text up to 39 characters.

All other options display date, time, or other job information that is obtained from the computer or printer driver when the job is printed.

5 Select the desired font, size, style, and angle of the text.

6 Select Print as footer also if you want the first available line of security watermark text to be printed at the bottom of the page. Select the page position from the list. This option is useful because the security watermark itself is not normally visible on the printed page.

7 Under Background pattern , select a design for the security watermark background.

Standard pattern

Select a design for the security watermark background. This option prints the selected pattern with the security watermark text or image.

Document guard pattern

The document guard design appears as the security watermark background.

This option prevents the printed page from being photocopied, scanned, faxed, or printed from memory. If a photocopy is attempted, then gray copy is

User Guide

Printer Driver

Advanced produced. If a scan, fax or print from memory is attempted, the process is stopped and an error message appears on the printing system’s operation panel.

8 Select Overprint for applications such as Microsoft PowerPoint and Internet

Explorer where the document content fills the entire page. The security watermark is printed over the document data so that it can appear in a photocopy. When editing an image, or if Device Settings > PDL Settings >

GDI compatible mode is selected, Overprint is selected automatically.

9 Adjust the calibration. After adjusting calibration, in all dialog boxes click OK .

Adjusting Security Watermark Calibration

For a security watermark to be effective, it must be nearly invisible in a printed page and clearly visible in a photocopied page. Because printing systems and driver settings can vary, you must adjust the calibration before printing a security watermark. Adjusting the calibration is also recommended when changing the background pattern, replacing the toner or printing system, and after heavy printing activity.

1 In Advanced > Security Watermark , click Add to create a custom security watermark; or under Select security watermark , select a default or custom security watermark and click Edit .

2 After all security watermark options are selected in the Add Security

Watermark or Edit Security Watermark dialog box, click Adjust Calibration .

3 Under Pattern shading and Text contrast , select initial options:

Light, Normal, Dark

Select the shading density of the background pattern.

Contrast 1-9

Select the level of contrast against the background pattern, from lightest to darkest.

These selections may need to be changed after printing a sample in the next step.

4 Click Print Sample to print a page displaying all nine contrast options against the selected pattern shading. It is recommended to print a sample page for each pattern shading option.

5 From the Text Contrast Sheet , find the sample where the security watermark is most nearly invisible.

6 In the Adjust Calibration dialog box, select options to match the sample chosen in step 5.

7 In all dialog boxes, click OK .

9-7

Advanced

Selecting Pages for Security Watermark

The Page selection options for security watermark determine where the security watermarks are placed in the print job.

1 In Advanced > Security Watermark > Select security watermark , choose a default or custom security watermark to print.

2 Under Page selection , choose pages for printing the security watermark:

All pages

This option prints the security watermark on each document page.

First page only

This option prints the security watermark on the first document page.

All pages except first page

This option prints the security watermark on all pages after the first page.

Only on specified pages

This option prints the security watermark on the page numbers typed in the text box.

Print onto front outside cover

This option prints the security watermark on the front cover. This option is available when Cover mode is selected in the Publishing tab. If Cover mode and Front outside are both selected in the Publishing tab, Print onto front outside cover is selected automatically.

Status Monitor

3 In all dialog boxes, click OK .

The Status Monitor displays printing system status messages in the lower right corner of the window during printing. You can start a status monitor for each supported printing system. More than one status monitor can be displayed at one time.

Selecting Status Monitor Options

You can select how to display the Status Monitor image and select from available options.

Note: The Status Monitor image closes on its own after 5 minutes, if there is no printing activity.

1 In the Advanced tab, click Status Monitor .

2 If you want the Status Monitor image to appear during a print job, in the Status

Monitor dialog box, select the Status Monitor check box.

3 To view the print job status without changing the Status Monitor setting, click

Open Status Monitor .

The Status Monitor image appears in the lower right corner of your computer screen.

9-8 User Guide

Printer Driver

Advanced

4 Move the pointer over the Status Monitor image to display balloon-style status messages containing information about printing system activity and the printer port. You can click the toner icon to display toner levels.

5 To display a list of options, right-click the Status Monitor icon in the system tray.

Hide the status monitor/Show the status monitor

Switches between hiding and showing the Status Monitor image.

Configure

Opens a web browser to display a printer web page.

Note: If your printer is connected with a USB cable, this feature cannot be used. Define settings using the operation panel of the printing system.

Always on top

Leaves the Status Monitor image on top of other open windows.

Opacity

Adjusts the Status Monitor to let a variable amount of background to show through the image. Select a percentage between 20 to 100.

Enlarge window

Select to increase the size of the Status Monitor image.

Notification

Opens a dialog box with options for Status Monitor event notifications and sound files.

www.kyoceradocumentsolutions.com

Opens a web browser to the KYOCERA Document Solutions Inc. home page.

Exit

Closes the Status Monitor image.

Setting Status Monitor Preferences

You can configure printing system alerts with accompanying sound or speech in the Status Monitor Preference dialog box.

1 Right-click the Status Monitor image in the system tray.

2 Click Notification .

3 Select the Enables Event Notification check box.

4 Select an event for a Status Monitor alert.

Cover open

Paper jam

Add paper

Sleep

Add toner

9-9

Advanced

Toner low

Not connected

Printing completed

Others

5 You can also add sound or speech to your chosen alert.

To add a sound file:

Clear the Use Text to speech check box.

The Sound file text box becomes available. Type the location of a sound file

(.WAV), or Browse to find a sound file located on your computer.

To add speech:

Select Use Text to speech .

Type your preferred text in the Text to speech text box. The Microsoft Text to Speech utility reads your typed text and plays it back in a spoken voice.

After you select a sound file, or type text for Text to speech, you can click the arrow below the text box to play the sound or speech.

EMF Spooling

6 Click Apply to save your settings, click OK to save your settings and close the dialog box, or click Cancel to close the dialog box without saving any settings.

EMF (Enhanced MetaFile) is a spool file format used in printing by the Microsoft

Windows operating system. When a print job is sent from an application, it is transferred to the spool file. The application writes to and the printer driver reads from the spool file simultaneously. For multiple or large documents, this quickly returns application control to the user while the printer is still printing the document.

Note: EMF spooling is unavailable when Allow data passthrough is selected in the KPDL Settings dialog box.

Selecting EMF Spooling

To print with EMF spooling:

1 From the Advanced tab, select the EMF Spooling check box.

2 Click OK and continue the printing process as usual.

Enable Client Profile

Client profile refers to profile settings saved on a client computer. You have the choice to use your local profiles or the server profiles. This feature is intended for the client computer in a client-server environment.

In the Advanced tab, clear the Enable client profile check box to select profiles from the server to apply to print jobs created by the driver. Server profiles are read–only.

Select the Enable client profile check box for using custom profiles locally in the driver.

9-10 User Guide

Glossary

A

B

C

D

E

G

Access code

A four-digit code that you must enter at the printing system’s operation panel to print a Private print job.

Application based printing

An administrator can associate a profile with an application so that all printing from the application uses the same profile settings. This makes profiles easier to use and ensures consistent printing from an application.

Auto configure

Device settings feature that queries a printing system through the network and automatically retrieves settings for optional devices and memory. Driver settings will be updated with information received from the physical printing system.

Installed devices display in the Preview image.

Booklet

Layout feature that prints a multi-page document in a booklet format by using a duplex unit. Two pages are printed on each side of a sheet to create a document that can be read like a book.

Cassette

A sliding plastic tray that holds a supply of paper for input to the printer.

Collate

Outputs the complete print job set by set. With Collate cleared, it prints each page by sets. For example, with Collate selected, three copies of a five-page document output as pages one through five in succession, three times.

Don’t use application name

Don’t use application name is an option to shorten the application defined job name for jobs created in Microsoft Word or PowerPoint.

The file name will appear clearly in the job list.

dpi

Dots per (linear) inch. Measurement that describes the sharpness and clarity of printed text and images. The higher the dpi, the more detail there is in the printed output.

EcoPrint

Imaging feature that changes toner saturation, making the entire image, text and graphics, appear lighter in the printed job. The actual amount of toner used depends on the printing system mode and the type of data printed (text, graphics, or both). EcoPrint does not increase print speed. This feature is also available in the

Quick Print and Basic tabs.

Edit Quick Print

This feature lets you customize the Quick Print view with your preferred print job options.

Enable client profile

Client profile refers to profile settings saved on a server and accessed by clients in a client/server environment. This feature in the Advanced tab lets an administrator control and distribute profiles.

GDI compatible mode

A page description language option that accurately reproduces what is viewed on the screen using the Microsoft Graphical Device

Interface (GDI) component to render the document. It generates data in a raster printing format, creating a larger printable file.

Printer Driver i

ii

I

J

H

L

M

Grayscale

Range of gray tones varying from black at the darkest to white at the lightest.

Gutter

Blank space on the left side or top of a printed page that can be increased by scaling down text and graphics. When used with Duplex printing, the enlarged blank space lines up evenly on both sides of the sheet. The larger blank space is created by shifting the printable area to the right or down as much as one inch (25.4

mm).

Half speed mode

This feature lets you reduce print speed to improve printing on small size, thick, or textured paper. Selecting this mode may result in quieter printing.

Halftone screen

Imaging process that breaks down an image into dots. An experienced user can adjust Halftone screen settings to create shades of gray in graphic images. Larger dots spaced close together create darker shades, and smaller dots spaced farther apart create lighter shades. Shading can be varied by adjusting the number of rows of dots, the angle at which rows of dots are placed, and the shape of the dots.

Ignore Application Collation

Check box in Device Settings > Compatibility that determines the priority of Collate settings. If the check box is selected, the printer driver setting is used. If the check box is cleared, the software application setting is used.

Job accounting

An accounting system that records and controls the number of pages printed by each account ID. Account IDs can be assigned at the printing system and stored in the driver. After account IDs are assigned, you can use the Job accounting option to print in the Job accounting mode.

Job name

A Job name is a unique identifier for each print job, to help you find and print the job from the printing system’s operation panel. When you send a print job using one of the Job storage (e-MPS) options, you can assign a custom name to the job or use the name of the application file.

Line Thinning

This feature reduces the pen width of lines used for barcodes and drawings. Drawing values controlled by an application are not changed. Line thinning is available when PCL XL is selected in the PDL Settings dialog box.

Lock Settings

Locking feature for some settings that an administrator can specify at the tab or feature level in the driver. The settings are then applied to print jobs from the driver, and changes are restricted. Locking a setting will also lock that setting where it appears in other tabs. The administrator can also set a password that is required to temporarily unlock a feature.

Media source enumeration

A Device Settings option that maintains compatibility for cassettes and feeders between old drivers and new drivers or when moving from one manufacturer to another. Compatibility creates a smooth transition for environments using macros or PRESCRIBE commands to access cassettes and feeders.

MP tray

Source tray used for transparencies, labels, envelopes, cardstock, coated media, and custom printing media.

User Guide

O

P

Printer Driver

Multiple pages per sheet

This feature lets you print several pages on a single sheet of paper for the purpose of reviewing the document and conserving paper.

Operation panel

The keys and display on the printing system. Use the operation panel to set options such as media type and EcoPrint, and to print jobs stored in RAM disk memory.

Optional Printer Components

Optional Printer Components include Common

Profiles and Plug-In Modules, and need to be installed separately from the driver installer. They are located on the Product Library disc in the Advanced Tools menu.

Orientation

The position of the pages in a print job, either short side at top

(portrait) or long side at top (landscape). If Rotate is selected, the print job orientation is rotated 180 degrees.

Pattern Scaling

Feature that can help improve visual compatibility between screen and print output. Graphics objects, such as a shape or a path, often include patterns and fills that are composed of collections of printed dots. A pattern is a planned or random repetition of colors, shapes, lines, values and textures to create a visual arrangement. A fill is the application of a color or grayscale to a graphics object.

If printed patterns and fills do not match the appearance of that on the screen, use

Pattern scaling to select a different density of printed dots.

PDF

The Adobe portable document format (PDF) is independent of the application software, hardware, and operating system used to create documents, and also of the output device on which they are displayed or printed.

PDL

Page Description Language. This is the language used by your computer to tell the printing device how to print a document. Availability of some printing options depends on the selected PDL.

Plug-in

An accessory program that integrates with the printer driver to enhance or extend the driver's capabilities.

Poster

Layout feature for printing a document in a larger size than the maximum supported by the printer so the cumulative sheets can be assembled as a poster. Use this feature to print a document in a large, eye-catching poster format, up to 25 times larger than the original document size.

PRESCRIBE

An internal printer language that embeds commands into specified locations in a print job.

Print graphics as black

This option prints all color graphics and text with black, rather than grayscale. This feature is intended for CAD applications.

Print preview

This feature lets you view your document before you send it to print.

Print text as black

Prints all color text as black. It produces faster printing of color print jobs by reducing the amount of data sent to the printer. In black and white printing, it increases the detail for light-colored text printed. White text and image colors are unaffected.

Private print

Job option that saves print jobs in RAM disk memory for printing until a four-digit access code is entered. Private print jobs are deleted when the printing system is reset or turned off.

iii

R

S

Q

T iv

Profile

A set of user defined driver settings that are saved as a group. Once saved, you can select a profile by name and apply its settings to a print job without selecting each feature individually.

Prologue/Epilogue

Advanced feature that allows you to insert a macro into specific locations in the print job. An advanced user may choose to use this feature to embed a PRESCRIBE command that will call a macro to overlay PRESCRIBE form data or a graphic object, such as a logo or a signature, at a specific point in the print job.

Proof and hold

Job option that prints one copy of a print job so that you can proof it before printing the remaining copies. This feature is available when RAM disk memory installed and selected in Device Settings. After the proof copy is printed and checked, remaining copies can be printed from the printing system’s operation panel without sending the job again from the computer.

Quick Print tab

The Quick Print tab improves usability by providing an easier way to set print options. You can choose basic settings or a predefined printer profile, rather than having to go to various tabs. Quick Print settings can be captured in a group called a profile. Profiles support common printing tasks, saving you from having to repeatedly select the same settings. The Administrator can set the view of the Quick

Print tab through the Installation process, or Administrator Settings in Properties.

Resolution

The number of dots printed in one inch. Higher resolution improves the quality of detailed printed images.

Scaling

Increases or decreases text and graphics on a page. Scaling is unavailable if other Layout tab options are selected.

Security Watermark

Plug-in feature that adds watermark text and a background pattern to a print job. The text blends into the background pattern making it nearly invisible when printed. The security watermark appears only when the printed page is photocopied. A security watermark can be used to help protect against unauthorized reproduction of documents, or simply to differentiate original documents from photocopies.

SNMP

Simple Network Management Protocol. The standard TCP/IP protocol for managing IP network devices, including printing devices. SNMP settings determine the level of security when using the Auto Configure feature, and prevent unauthorized printing to the SNMPv3 printing device. SNMP settings must be set in the

Administrator settings in Device Settings, and in the printing system’s Command

Center.

Status monitor

Optional feature that displays printing system status messages in the lower right corner of the window during printing. You can customize the appearance of the status monitor, and determine what messages are displayed and how by selecting preferences and notifications.

Transparency

A clear plastic, page-sized sheet used as a printing medium.

Transparency interleaving

Publishing feature that inserts a backing sheet between printed transparencies. The backing sheet, also known as an interleaf, helps keep transparencies clean and prevents them from clinging together.

User Guide

U

W

User login

Registers users with a user name and password. User login provides job restriction by user, in contrast to the Job accounting feature, which assigns privileges by division or department.

Watermark

The Watermark feature is available in the Advanced tab. A watermark is a recognizable image or pattern that can be placed on a page or throughout a document. You can choose one of the standard watermarks or create your own text.

Printer Driver v

KYOCERA Document Solutions America, Inc.

Headquarters

225 Sand Road,

Fairfield, New Jersey 07004-0008, USA

Phone: +1-973-808-8444

Fax: +1-973-882-6000

Latin America

8240 NW 52nd Terrace Dawson Building, Suite 100

Miami, Florida 33166, USA

Phone: +1-305-421-6640

Fax: +1-305-421-6666

KYOCERA Document Solutions Canada, Ltd.

6120 Kestrel Rd., Mississauga, ON L5T 1S8,

Canada

Phone: +1-905-670-4425

Fax: +1-905-670-8116

KYOCERA Document Solutions

Mexico, S.A. de C.V.

Calle Arquimedes No. 130, 4 Piso, Colonia Polanco

Chapultepec, Delegacion Miguel Hidalgo,

Distrito Federal, C.P. 11560, México

Phone: +52-555-383-2741

Fax: +52-555-383-7804

KYOCERA Document Solutions Brazil, Ltda.

Av.Tambore,1180 Mod.B-09 CEP 06460-000

Tambore-Barueri-SP, Brazil

Phone: +55-11-4195-8496

Fax: +55-11-4195-6167

KYOCERA Document Solutions

Australia Pty. Ltd.

Level 3, 6-10 Talavera Road North Ryde N.S.W, 2113,

Australia

Phone: +61-2-9888-9999

Fax: +61-2-9888-9588

KYOCERA Document Solutions

New Zealand Ltd.

1-3 Parkhead Place, Albany, Auckland 1330,

New Zealand

Phone: +64-9-415-4517

Fax: +64-9-415-4597

KYOCERA Document Solutions Asia Limited

16/F.,Mita Centre, 552-566, Castle Peak Road

Tsuenwan, NT, Hong Kong

Phone: +852-2610-2181

Fax: +852-2610-2063

KYOCERA Document Solutions

(Thailand) Corp., Ltd.

335 Ratchadapisek Road, Bangsue, Bangkok 10800,

Thailand

Phone: +66-2-586-0333

Fax: +66-2-586-0278

KYOCERA Document Solutions

Singapore Pte. Ltd.

12 Tai Seng Street #04-01A,

Luxasia Building, Singapore 534118

Phone: +65-6741-8733

Fax: +65-6748-3788

KYOCERA Document Solutions

Hong Kong Limited

16/F.,Mita Centre, 552-566, Castle Peak Road

Tsuenwan, NT, Hong Kong

Phone: +852-2429-7422

Fax: +852-2423-2159

KYOCERA Document Solutions

Taiwan Corporation

6F., No.37, Sec. 3, Minquan E. Rd.,

Zhongshan Dist., Taipei 104, Taiwan R.O.C.

Phone: +886-2-2507-6709

Fax: +886-2-2507-8432

KYOCERA Document Solutions Korea Co., Ltd.

18F, Kangnam bldg, 1321-1,

Seocho-Dong, Seocho-Gu, Seoul, Korea

Phone: +822-6933-4050

Fax: +822-747-0084

KYOCERA Document Solutions

India Private Limited

First Floor, ORCHID CENTRE

Sector-53, Golf Course Road, Gurgaon 122 002,

India

Phone: +91-0124-4671000

Fax: +91-0124-4671001

KYOCERA Document Solutions Europe B.V.

Bloemlaan 4, 2132 NP Hoofddorp,

The Netherlands

Phone: +31-20-654-0000

Fax: +31-20-653-1256

KYOCERA Document Solutions Nederland B.V.

Beechavenue 25, 1119 RA Schiphol-Rijk,

The Netherlands

Phone: +31-20-5877200

Fax: +31-20-5877260

KYOCERA Document Solutions (U.K.) Limited

8 Beacontree Plaza,

Gillette Way Reading, Berkshire RG2 0BS,

United Kingdom

Phone: +44-118-931-1500

Fax: +44-118-931-1108

KYOCERA Document Solutions Italia S.p.A.

Via Verdi, 89/91 20063 Cernusco s/N.(MI),

Italy

Phone: +39-02-921791

Fax: +39-02-92179-600

KYOCERA Document Solutions Belgium N.V.

Sint-Martinusweg 199-201 1930 Zaventem,

Belgium

Phone: +32-2-7209270

Fax: +32-2-7208748

KYOCERA Document Solutions France S.A.S.

Espace Technologique de St Aubin

Route de I’Orme 91195 Gif-sur-Yvette CEDEX,

France

Phone: +33-1-69852600

Fax: +33-1-69853409

KYOCERA Document Solutions Espana, S.A.

Edificio Kyocera, Avda. de Manacor No.2,

28290 Las Matas (Madrid), Spain

Phone: +34-91-6318392

Fax: +34-91-6318219

KYOCERA Document Solutions Finland Oy

Atomitie 5C, 00370 Helsinki,

Finland

Phone: +358-9-47805200

Fax: +358-9-47805390

KYOCERA Document Solutions

Europe B.V., Amsterdam (NL) Zürich Branch

Hohlstrasse 614, 8048 Zürich,

Switzerland

Phone: +41-44-9084949

Fax: +41-44-9084950

© 2012 KYOCERA Document Solutions Inc.

is a trademark of KYOCERA Corporation

KYOCERA Document Solutions

Deutschland GmbH

Otto-Hahn-Strasse 12, 40670 Meerbusch,

Germany

Phone: +49-2159-9180

Fax: +49-2159-918100

KYOCERA Document Solutions Austria GmbH

Eduard-Kittenberger-Gasse 95, 1230 Vienna,

Austria

Phone: +43-1-863380

Fax: +43-1-86338-400

KYOCERA Document Solutions Nordic AB

Esbogatan 16B 164 75 Kista, Sweden

Phone: +46-8-546-550-00

Fax: +46-8-546-550-10

KYOCERA Document Solutions Norge NUF

Postboks 150 Oppsal, 0619 Oslo,

Norway

Phone: +47-22-62-73-00

Fax: +47-22-62-72-00

KYOCERA Document Solutions Danmark A/S

Ejby Industrivej 60, DK-2600 Glostrup,

Denmark

Phone: +45-70223880

Fax: +45-45765850

KYOCERA Document Solutions Portugal Lda.

Rua do Centro Cultural, 41 (Alvalade) 1700-106 Lisboa,

Portugal

Phone: +351-21-843-6780

Fax: +351-21-849-3312

KYOCERA Document Solutions

South Africa (Pty) Ltd.

49 Kyalami Boulevard,

Kyalami Business Park 1685 Midrand, South Africa

Phone: +27-11-540-2600

Fax: +27-11-466-3050

KYOCERA Document Solutions Russia LLC

Botanichesky pereulok 5, Moscow, 129090,

Russia

Phone: +7(495)741-0004

Fax: +7(495)741-0018

KYOCERA

Document Solutions

Middle East

Dubai Internet City, Bldg. 17,

Office 157 P.O. Box 500817, Dubai,

United Arab Emirates

Phone: +971-04-433-0412

KYOCERA Document Solutions Inc.

2-28, 1-chome, Tamatsukuri, Chuo-ku

Osaka 540-8585, Japan

Phone: +81-6-6764-3555 http://www.kyoceradocumentsolutions.com

Rev. 15.16 2012.06