WerkMaster TITAN XT Propane, COLOSSOS XT Propane Floor Machine OPERATOR'S MANUAL
Διαφήμιση
Διαφήμιση
OPERATOR’S MANUAL
IMPORTANT: Read before using your new machine
WerkMaster Grinders and Sanders Inc.
6932 Greenwood Street, Burnaby, BC V5A 1X8 tel: 604.629.8700 | toll free: 1.866.373.WERK | fax: 604.444.4231 www.werkmaster.com | email: [email protected]
© Copyright 2013
LIABILITY LIMITATIONS
The remedies of the user set forth under provisions of warranty outlined at the end of this manual are the exclusive and total liability of WerkMaster Grinders and Sanders Inc. with the respect to their sale or the equipment and service furnished hereunder, in connection with the performance of breach thereof, or from the sale, delivery, installation, repair or technical direction covered by or furnished under the sale, whether based on contract, warranty, negligence, indemnity, strict liability, or otherwise shall not exceed the purchase price of the unit of equipment upon which such liability is based.
WerkMaster will not in any event be liable to the user, any successors in interest or any beneficiary or assignee relating to this sale for any consequential, incidental, indirect, special or punitive damages arising out of this sale or any breach thereof, or any defects on, or failure of, or malfunction of the equipment under this sale based upon loss of use, lost profits or revenue, interest, lost goodwill, work stoppage, impairment of other goods, loss by reason of shutdown or non-operation, increased expenses of operation of the equipment, cost of purchase or replacement power of claims of users or customers of the user for service interruption whether or not such loss or damage is based on contract, warranty, negligence, indemnity, strict liability, or otherwise.
WerkMaster reserves the right to modify, alter and improve any part or parts without incurring any obligation to replace any part or parts previously sold without such modified, altered or improved part or parts.
No person is authorized to give any other warranty or to assume any additional obligation on WerkMaster’s behalf unless made in writing and signed by an officer of WerkMaster.
USE ONLY GENUINE WERKMASTER PARTS AND ACCESSORIES FOR
YOUR OWN SAFETY, THE SAFETY OF OTHERS AND THE LIFE OF YOUR
MACHINE.
CONTENTS
Introduction ......................................................................................................... 1
Machine Descriptions ......................................................................................... 2
Specifications ...................................................................................................... 2
Safety Precautions .............................................................................................. 3
PROPANE SAFETY INFORMATON .................................................................... 5
Facts About LP Gas Propane ........................................................................... 5
Facts About Propane Tanks .............................................................................. 5
Recommended Purge Procedure ...................................................................... 6
Filling Propane Tanks ....................................................................................... 6
Storing Propane Tanks ..................................................................................... 7
Storing the Machine .......................................................................................... 7
Transporting the Machine ................................................................................. 7
ENGINE EMISSIONS AND CARBON MONOXIDE SAFETY .............................. 8
CO Exposure Limits .......................................................................................... 8
Methods to Reduce the Risks of CO Poisoning ................................................ 8
ClearSKY TECHNOLOGY ................................................................................... 9
EMISSION CONTROL SYSTEM ........................................................................ 10
MACHINE OPERATION ..................................................................................... 11
Machine Controls ........................................................................................... 11
Preparing the Machine for Use..
…………………………………………………
11
EZ Bak Tilt Operation
……………………………………………………………
...12
Changing the Tooling
……………………………………………………………
..13
Adjusting the Dust Skirt
…………………………………………………………
...13
Installing and Removing the Propane Tank
……………………………………
14
Adjusting the Handle
………………………………………………………………
15
Removing and Reattaching the Handle Assembly
……
.
………………………
.15
Attaching the Vacuum Hose
……………………………………………………
...16
Starting the Machine
………………………………………………………………
17
Adjusting the Speed
………………………………………………………………
.18
Activating the Tooling
……………………………………………………………
.18
Stopping the Engine
………………………………………………………………
.18
Stopping the Machine
……………………………………………………………
..18
MAINTENANCE
………………………………………………………………………
.19
General and Recommended Maintenance Items
…
.
…………………………
..19
Daily
…………………………………………………………………………………
19
Weekly
………………………………………………………………………………
19
Monthly
…………………………………………………………
..
…………………
.19
Maintenance Charts
………………………………………………………………
.20
Plug 'N Go Tooling
…………………………………………………………………
22
Indexing
………………
.
……………………………………………………………
.22
Installing and Removing the Pad Driver
…………………………
.
……………
..23
Rotation Pattern of Tooling Plates
………………………………………………
.23
Installing and Removing the Battery
…………………………………………
.
…
.24
Changing the Oil
……………………
..
……………………………………………
.24
Changing the Oil Filter
……………………………………………………………
.25
Changing the Air Filter..
………………………………………………………
.
…
..26
TROUBLESHOOTING ....................................................................................... 27
EXPLODED VIEW AND PARTS LISTS ............................................................. 28
WARRANTY INFORMATION ............................................................................. 34
QUICK REFERENCE OPERATION AND SAFETY GUIDES
…………
...
……
.
…
35
OPERATOR’S MANUAL
Page III
INTRODUCTION
Congratulations on your purchase of a WerkMaster propane machine.
WerkMaster machines allow professional surface prep, polishing, grinding, edging, buffing and restoration of virtually any surface material, including concrete, terrazzo, and stone. This manual is provided to assist you in the operation and maintenance of your WerkMaster machine.
WerkMaster has patented Octi-Disc technology with 8 counter rotating heads; that means more tools make more passes over the surface with greater speed,
resulting in incredible productivity that no other machine can match.
IMPORTANT
WerkMaster is dedicated to our customers, their safety, and to providing information, services, and products that meet their needs.
Read this manual and all the safety precautions before attempting to operate WerkMaster machines. Failure to follow the safety precautions may result in damage to the machine, severe personal injury, or death.
If you or your operator cannot read English, have the manual explained fully before
attempting to operate the machine.
DANGER
It is the owner/operator’s responsibility to ensure that the air-exchange system installed in any location where a propane grinder/polisher is being operated is of sufficient capacity and quality to support the use of such a machine. OSHA, WCB and other county, state, or federal agencies publish safety guidelines. Failure on the part of the owner/operator to ensure that a propane grinder/polisher can be operated safely in a given location may lead to injury, sickness or even loss of life.
This Operator's Manual has been prepared for instructional purposes only.
WerkMaster does not claim or assume any responsibility for the operator's actions or safety.
To be completely aware of what local authorities require, contact the OSHA/WCB
agency in your community.
OPERATOR’S MANUAL
Page 1
MACHINE DESCRIPTIONS
WerkMaster machines include the Scarab, Termite XT, Viper XT, Raptor XT,
TITAN XT and the COLOSSOS XT models. To see the complete family of
WerkMaster machines, informational videos, tooling guide, chemicals and
accessories, visit our website at www.werkmaster.com
.
TITAN XT Propane and COLOSSOS XT Propane
• 7 Machines in 1– grinder, stripper, sander, buffer, burnisher, polisher and edger
•
Remove thinset, epoxy, glue, paint, mastic, and micro toppings; work on spalled or rained out concrete
•
Run wet or dry on concrete, stone, and terrazzo
• Exceed OSHA standards for indoor operation ensuring the safety of the operator and the workplace environment
•
Edge to within 1/8” (3 mm) of the wall
• Come with EZ Bak tilt and adjustable, foldable handle for easy transport
• with an optional water feature.
The TITAN XT Propane
• Features WerkMaster Octi-Disc
TM
technology with 8 counter rotating heads and the versatility of using our 6 3/4” (171 mm) ULTRA-FLEX Plug ‘N Go tooling system
• Easy to use and operator friendly, with a 20” (51 cm) footprint
•
Uses a powerful 18 HP Kawasaki motor with variable speed controls on the handle
• Features an electric clutch
The COLOSSOS XT Propane
• Features WerkMaster Octi-Disc
TM
technology with 8 counter rotating heads and the versatility of using our 8” (203 mm) ULTRA-Flex Plug ‘N Go tooling system
•
Easy to use and operator friendly the Colossos XT Propane weighs only 800 lbs (364 kg), with a 24” (61 cm) footprint
• Uses a powerful 27 HP Kawasaki motor with variable speed controls on the handle
SPECIFICATIONS
MODEL TITAN XT Propane
Dimensions (l x w in)
(l x w cm)
20 x 20
51 x 51
Weight (lbs / kg) 600 / 272
Kawasaki Motor (HP) 18
Tank Capacity (lbs / kg) 20 / 9.1
COLOSSOS XT Propane
24 x 24
61 x 61
800 / 364
27
33 / 15
OPERATOR’S MANUAL
Page 2
SAFETY PRECAUTIONS
Definitions
IMPORTANT
Read this manual and all the safety precautions before attempting to operate WerkMaster machines. Failure to follow the safety precautions may
result in severe personal injury or death.
• DANGER indicates severe bodily injury or death may occur to you or other persons if safety precautions are ignored or are not adhered to. Read and observe all DANGER statements found in the Owner's Manual and on your machine.
• WARNING indicates injury may occur to you or to other persons if safety precautions are ignored or are not adhered to. Read and observe all
WARNING statements found in the Owner's Manual and on your machine.
• CAUTION indicates damage may occur to the machine or to other property if safety precautions are ignored or are not adhered to. Read and observe all
CAUTION statements found in the Owner's Manual and on your machine
.
DANGER
Failure to read the Owner's Manual prior to operating or attempting any service or maintenance procedure to your WerkMaster machine could result in damage to the machine, injury to you or to other personnel, or death.
1. The moving parts of this machine can cause serious injury and/or damage.
The operator must wear appropriate clothing and footwear. Do not allow clothing, hair, hands, feet, or other body parts to come into contact with rotating parts. Keep people away from the machine while it is in operation.
2. NEVER try to change the tooling or attempt to make adjustments to the machine while it is operation. Injury to the operator or bystanders could occur if the engine is running while changing the tooling or making adjustments.
3. Propane is a highly flammable fuel. Cigarette lighters, pilot lights or any other source of ignition may cause an explosion if it comes in contact with propane. All sources of ignition should be extinguished or removed entirely from the work area. DO NOT SMOKE in the vicinity of a propane grinder.
4. This machine emits carbon monoxide (CO). Asphyxiation could occur if the unit is used in an area with poor or inadequate ventilation. ONLY operate machine in a well-ventilated area. If the operator develops a headache, confusion, light-headedness, vertigo, drowsiness, dizziness and/or nausea
SHUT OFF THE MACHINE IMMEDIATELY. Move to a well-ventilated area.
If symptoms persist, get medical attention. Have the machine checked for carbon monoxide emissions by a qualified technician before using again.
5. Dangerous carbon monoxide emissions from this machine are greatly increased due to a dirty combustion air cleaner. Follow the engine manufacturer’s air cleaner service instructions.
OPERATOR’S MANUAL
Page 3
6. If you smell propane gas, shut off the machine and move it outside.
Determine the source of the leak before using it again. NEVER vent propane gas inside a building. It is UNLAWFUL to store a propane bottle inside a building.
7. NEVER operate a WerkMaster machine under the influence of drugs, alcohol or when taking medications that impair the senses or reactions, or when excessively tired or under stress.
8. Crystalline silica from bricks and concrete and other masonry products can cause health problems. Your risk of exposure to this varies depending on how often this type of work is done. To reduce the risk, work in a wellventilated area, use a dust control system such as an industrial-style vacuum, and wear approved personal safety equipment such as a dust/particle respirator designed to filter out microscopic particles.
WARNING
1. ALWAYS wear hearing protection while using this machine. Long or continuous exposure to high noise levels may cause permanent hearing loss.
2. ALWAYS wear safety goggles and safety clothing while using this machine.
Injury to the eyes and/or body can occur if protective clothing and/or equipment are not worn while using this machine.
3. DO NOT touch the muffler or exhaust pipe when they are hot. Severe burn or injury may occur.
4. Any alterations or modifications to this machine may result in damage to the machine or injury to the operator or bystanders. Alterations or modifications not authorized by the manufacturer voids any and all warranties and liabilities.
5. To avoid injury or property damage, do not leave the machine where it can be tampered with or started by persons untrained in its operation. DO NOT leave the machine running unattended.
6. Vibration from machinery may cause numbness or tingling of the fingers.
Wearing warm clothing, gloves, exercising and refraining from smoking can reduce the effects of vibration. If the symptoms persist, discontinue operation of the machine.
7. Equipment should only be operated by personnel familiar with the correct and safe operation of the machine; who are in good physical condition and mental health (not fatigued). The operator and maintenance personnel must be physically able to handle the bulk, weight and power of this equipment.
8. This is a one-person machine. Maintain a safe operating distance from other personnel. It is the operator’s responsibility to keep bystanders away during operation. Block off the work area in all directions with roping, safety netting, etc. for a safe distance. Failure to do so may result in others being injured by flying debris or being exposed to harmful dust and noise.
OPERATOR’S MANUAL
Page 4
9. Be sure all safety decals on the machine can be clearly read and understood.
Replace damaged or missing decals immediately.
10. Maintain the machine in safe operating condition with all guards in place and secure, all mechanical fasteners tight, all controls in working order and the grinder configured for the job application. DO NOT operate this machine if there are loose parts. Frequently inspect the machine for loose parts. This will promote safe operation and a long life for the machine.
11. To prevent damage to the grinder and/or serious personal injury, avoid protruding slab inserts, nails, screws, Hilti anchors, rebar, embedded bolts, debris, pipe extensions, machinery bases or any objects that transmit a sudden shock to the grinding assembly.
12. Inspect the discs carefully before installing. Do not use any discs that exhibit signs of damage since serious personal injury and/or damage to the equipment may result.
CAUTION
NEVER OVERFILL THE PROPANE TANK. ONLY FILL TO 80%.
1. Overfilling the propane tank is the number one cause of problems with a propane machine.
Overfilling may cause the engine to run poorly or not at all. Overfilling allows propane to enter the fuel control system, possibly ruining the lock off / regulator assembly. This voids the warranty on affected parts of the machine. To avoid problems, read and understand fully, the section Filling Propane Tanks. It is recommended to always have an authorized propane dealer fill the tank(s) and to use tanks with an Overfill
Protection Device (OPD).
PROPANE SAFETY INFORMATON
Facts About
LP Gas Propane
Facts About
Propane Tanks
As a fuel, propane gas is unmatched for both safety and dependability. It has been used as a domestic household fuel for over half a century and for over thirty years as an internal combustion engine fuel. Propane is a highly flammable fuel that is contained under pressure as a liquid. Vaporized gas has a similar explosive force to gasoline and mixtures as low as 2% LP gas-to-air may be ignited in a closed environment. Care should be exercised to avoid escaping vapor as it can freeze skin and cause frost bite. Vaporized fuel is heavier than air and will collect in the lowest confined space available.
Propane tanks are constructed according to ASME or Federal DOT #4ET20 pressure safety codes. Including the tank, all valves and fittings are UL listed.
Propane gas is noncorrosive and will not rust the inside of a tank. Should the tank exterior become damaged or rusted, discontinue use. DO NOT tamper with tank gauges or safety relief valves. NEVER use a tank not intended for use with a propane buffer. DO NOT substitute tanks that are used with a barbecue grill, etc. WerkMaster recommends having propane tanks tested once a year by an authorized National LP Gas Association propane dealer.
OPERATOR’S MANUAL
Page 5
Recommended
Purge Procedure
The fuel tank is supplied directly from the manufacturer and is empty of fuel. The tank must be purged at the time of the first fill. Local propane fuel vendors should be familiar with this operation and will provide this service.
New containers may contain vapor, air, or other contaminants. It is essential that these be removed before filling the container and putting it into service. Air in the container will cause abnormally high pressure, with the result that the pressure relief valve may open. Air in the system is also likely to cause a lean mixture, making ignition difficult. If a cylinder is suspected of being depressurized or open to the atmosphere for a period of time, it must be re-purged.
See an authorized propane dealer for proper purging of your tank.
Symptoms of a non-purged cylinder:
• Relief valve opens due to over-pressurized cylinder creating hazardous situation.
• Moisture in the cylinder.
• Grinder operates initially but shuts down when fuel mixture becomes too lean.
Filling Propane
Tanks
The TITAN XT Propane uses a 20 lb (9.1 kg) and the COLOSSOS XT Propane uses a 33 lb (15 kg) capacity aluminum or steel tank that meets the DOT 4E240 standards. These standards are also listed by UL. The steel cylinder meets
European TPED specifications and is CE compliant.
ALWAYS have an authorized propane dealer fill your tank. Fill through the service valve ONLY.
OVERFILLING PROPANE TANKS IS HAZARDOUS. The tank should NEVER be completely filled; 80% of the total tank volume is considered full at ALL times.
EXPANSION MUST BE ALLOWED FOR.
CAUTION
The engine and the fuel system on your WerkMaster are designed to run on vapor propane, NOT liquid propane. Liquid propane and vapor propane are NOT interchangeable. Interchanging the fuel will VOID THE WARRANTY.
OPERATOR’S MANUAL
Page 6
Storing Propane
Tanks
•
Propane tanks should NOT be stored in buildings used by employees, the public, or frequented by anyone passing through.
•
When not in use, propane tanks should always be stored in an upright position in a secure, tamper-proof, steel mesh storage cabinet. The cabinet may be located next to the building, but with at least five (5) feet (1.5 m) of space between the cabinet and the nearest building opening (door or window).
• Full or empty, propane tanks should NEVER be left or stored in small, enclosed areas, in an enclosed van or trailer, or near an open flame or heatproducing device.
WARNING
PROPANE TANKS SHOULD ALWAYS BE INSTALLED, USED, STORED,
AND TRANSPORTED IN AN UPRIGHT POSITION.
The National Fire Protection Association (NFPA) Standard for Storage and
Handling of LP Gas is the appropriate authority for safe propane use. A copy of this publication is available through the National Fire Protection Association
(1.800.344.3555) or www.NFPA.org.
Storing the
Machine
•
Store machine in a dry location, temperature not to exceed 120° F (50° C), away from objects that may fall and damage it, and away from open flames or heat producing devices.
• NEVER store the machine with propane tanks installed.
•
Make sure the machine is properly cleaned before storing.
Transporting the Machine
• When transporting a propane-powered machine with the propane tank installed, the tank should be securely fastened and the service valve closed.
Any propane tanks not installed should be upright and securely fastened to avoid movement and damage.
• Check the propane tanks for overfilling BEFORE transporting; if overfilled use the bleeder valve to vent the propane outside in a safe area. See diagram on page 14.
•
Ensure the machine if turned OFF when loading onto a truck or trailer.
•
ONLY use a truck or trailer that will support the weight of the machine.
• Block the wheels and tie the machine down securely to the truck or trailer.
OPERATOR’S MANUAL
Page 7
ENGINE EMISSIONS AND CARBON MONOXIDE SAFETY
CO Exposure Limits
Methods to Reduce the Risks of CO
Poisoning
DANGER
All engines powered by LPG (Liquid Propane Gas), including this engine, produce carbon monoxide (CO). It is a FATAL POISON gas that is a colorless, odorless, tasteless, and non-irritating. It is produced by incomplete combustion of carbonaceous material such as LPG.
Failure to provide for proper venting of CO produced during the operation of combustion-powered engines may result in SERIOUS INJURY OR DEATH to the operator and those in the contaminated area.
The effects of CO can be experienced at different exposure levels, depending on the health of the individual. Conditions that affect the tolerance of the individual are smoking, age, temperature, humidity, and other conditions.
Symptoms include light-headedness, confusion, headaches, vertigo, drowsiness, dizziness and/or nausea.
If the operator experiences any of these symptoms STOP USING THE
MACHINE IMMEDIATELY. Move to a well-ventilated area. If symptoms persist,
get medical attention.
WARNING
All distributors, owners, and operators should be aware of the potential effects of
CO and the methods used to prevent over-exposure.
Please refer to OSHA, WCB or local workplace industry guidelines for CO exposure limits.
Air Exchange and CO Diffusion
CO does not mix with air on its own. Air currents can "stir" the CO and dilute the concentration values by mixing it with the available air. Stirring the air can occur by walking and with the use of fans and ventilation systems.
Application Considerations
Consider the operation you are performing and the size of the area to be worked.
A low movement operation such as glue/mastic removal in a smaller area will increase the build-up of CO; while a much quicker operation, such as polishing with 3000 grit over the same area, may not have the same potential for CO buildup.
Stirring or CO mixing MUST be forced by the use of fans in order to reduce the high concentration of CO when activity is concentrated to a smaller area while performing a low movement operation.
OPERATOR’S MANUAL
Page 8
Air Quality Monitoring
Use of a monitor/detector is essential for the safe operation of any equipment that has the potential to produce CO. See local regulations for the approved monitors/detectors and their correct methods of use.
Room Size and Time Estimations
The concentration and volume of CO production, the size of the area, and the amount of air exchange are factors involved with determining safe time limits for operation in a specific room size.
The smaller the work area and the slower the movement, the greater the build-up
of CO. Fans MUST be used to stir the air and reduce the concentration of CO.
Maintenance of Equipment
LPG engines are dependent on engine tune-ups and air filter replacements. CO concentration (production) increases when the air-to-fuel ratio becomes fuel rich.
Follow the recommended Maintenance Schedule for the engine.
CO Safety Equipment Available
WerkMaster propane machines are equipped with a catalytic muffler and a
ClearSKY monitoring system to reduce the CO emissions and to promote a safer work environment.
CLEARSKY TECHNOLOGY
WerkMaster’s ClearSKY GREEN, environmentally friendly technology meets
LEED standards and contains multiple safety features to ensure safe operation while creating a clean environment. WerkMaster machines are manufactured to exceed EPA and OSHA safety standards for carbon monoxide emissions. The technology delivers a 98% reduction in emissions over conventional propane
systems.
OPERATOR’S MANUAL
Page 9
EMISSION CONTROL SYSTEM
WerkMaster propane machines are equipped with a catalytic muffler and a
ClearSKY monitoring system to reduce the CO emissions and to promote a safer work environment.
The ClearSKy emission control unit has an on-board diagnostic system that allows for constant monitoring of the engine by precisely maintaining the air-tofuel ratio (A/F).
The RED CHECK ENGINE LIGHT comes on when starting up; indicating that power is being supplied to the engine. It goes out after 40 seconds. If the controller is unable to maintain the proper mixture, the red light will come on and stay on indicating that engine maintenance and/or service is needed. The
CHECK ENGINE light is triggered by rich conditions lasting longer than 1 1/2 – 2 minutes.
The YELLOW O2 SENSOR LIGHT is yellow on initial start-up. After 40 seconds it becomes a monitoring light for the oxygen sensor. A green color indicates lean condition; a red color indicates rich condition. If the light is cycling steadily from green to red it indicates proper control of the A/F mixture.
A steady lean condition (GREEN) or a steady rich condition (RED) indicates that the controller is unable to maintain the stoichiometric A/F ratio, signaling a problem with the engine and/or the controller.
The four ORANGE MODULATION LIGHTS indicate the modulation percentage of the solenoid valve. It is normal for these lights to oscillate indicating changing modulation as required to control the A/F mixture.
Tampering with the Emission Control System is prohibited and will VOID THE
WARRANTY.
DO NOT alter, change or tamper with:
• Carburetor and internal parts
• Spark plugs
• Magneto or electronic ignition system
•
Fuel filter element
• Air cleaner elements
• Crankcase
• Cylinder heads
• Breather chamber and internal parts
• Intake pipe and tube
•
Throttle body and internal parts
• Fuel lock-off
• Intake pipe and tube
NOT an all-inclusive list.
OPERATOR’S MANUAL
Page 10
MACHINE OPERATION
Machine Controls
Preparing the
Machine for Use
G
D
F
G
D
H
A
C
B
B
E
• Ignition Switch (A) – Used to start machine.
• Emergency Stop Button (B) – Used to stop machine in the event of an emergency.
• Throttle Control Lever (C) – Used to control the speed of the engine.
• Clutch Levers (D) – When applied, the clutch will engage and the pad drivers under the machine will spin.
• Handle Adjustment Pin (E) – Used to adjust the height of the handle for operating, transporting and tilting the machine for tooling changes.
• Green Engine START Button (F) – Used to start engine.
• Yellow Light (G) – Indicates the key is in the RUN position and that the machine can be started.
• Hour Meter/Tachometer (H) – Records the number of hours a machine has been powered ON and displays the engine speed. The meter displays hours when the machine is turned OFF and the engine speed when the machine is turned ON.
BEFORE using any type of power equipment, proper safety dictates you should inspect the machine.
1.
Adjust the handle to a comfortable height and tighten the bolts.
2.
Make sure the bonnet dust filter on top of the engine is clean.
3.
Inspect the air filter. Clean or replace as needed.
4.
Check the engine OIL LEVEL before starting the machine and every four
(4) hours thereafter. DO NOT screw the dipstick in to get the reading.
5.
ALWAYS have the propane tank filled by an authorized propane dealer.
6.
Inspect the condition of the pad driver and tooling. Ensure the pad driver and tooling are properly attached, in good condition and that each pad driver has grommets securing the tooling. ALWAYS turn off the engine to
clean or replace the pad driver or tools.
7.
Check the fuel lines for signs of wear and tear such as cracks or corrosion.
OPERATOR’S MANUAL
Page 11
EZ Bak
Tilt Operation
EZ Bak Tilt Operation
For the TITAN XT Propane:
A
B
Fig 1 Fig 2
1. Close the valve on the propane tank.
2. Allow the engine to stop and turn the ignition key OFF.
3. Lower the step down plate (B) by releasing the pull pin (A).
4. Remove the propane tank.
5. Ensure the handle is in its full upright position (Fig 1). Tilt the machine back by stepping on the step down plate and pulling down on the handle (Fig 2).
6. Slowly lift the machine back to the upright position by using the step down plate to prevent the TITAN XT Propane from hitting the floor.
7. Reinstall the propane tank.
8. Fold the step down plate up and secure by replacing the pull pin.
For the COLOSSOS XT Propane:
A
Fig 1 Fig 2
1. Close the valve on the propane tank.
2. Allow the engine to stop and turn the ignition key OFF.
3. Lower and unfold the step down plate (B) by releasing the pull pin (A).
B
4. Remove the propane tank.
5. Ensure the handle is in its full upright position (Fig 1). Tilt the machine back by unfolding and stepping on the step down plate and pulling down on the handle (Fig 2).
OPERATOR’S MANUAL
Page 12
6. Slowly lift the machine back to the upright position by using the step down plate to prevent the COLOSSOS XT Propane from hitting the floor.
7. Reinstall the propane tank.
8. Fold the step down plate in and up and secure by replacing the pull pin.
Changing Tooling
WARNING
ALWAYS turn the engine OFF when performing any operation to the bottom of the machine.
Rubber
Grommets
Tooling
To change tooling:
1. Close the valve on the propane tank.
2. Allow the engine to stop and turn the ignition key OFF. Remove the propane tank.
3. Ensure the handle is in its full upright position. Tilt the machine back to the
EZ Bak position.
4. Choose the appropriate tooling holder attachment – magnetic Plug ‘N Go plate for Metal Bond tools or Foam/Velcro Adapter plate.
5. Insert the two (2) shear pins into the rubber grommets. Attach the corresponding tooling to the plate. Follow the above diagram for tooling
placement. Refer to the Tooling Selection Guide at www.werkmaster.com/machine-specific-tooling for the best choice of tooling and the number of tools needed per plate.
6. Return the machine to the upright position following EZ Bak instructions.
Adjusting the
Dust Skirt
The dust skirt serves as a seal for the bottom of the machine to act as a vacuum chamber helping the dust stay contained under the machine. If the skirt is too far from the ground, the dust containment is reduced.
To adjust the skirt:
1. Pull one end of the skirt off of the machine until you reach the middle of the skirt.
OPERATOR’S MANUAL
Page 13
2. Position the skirt until it’s barley touching the ground and repeat with the other end.
Installing and
Removing the
Propane Tank
WARNING
Avoid positioning the dust skirt too low, as it will drag against the ground wearing
it out prematurely and possibly preventing smooth machine movement.
To install the propane tank:
1. Slowly lower the step down plate by releasing the pull pin.
2. Undo the Velcro strap. Place the propane tank in the shroud housing and position to allow access to the service valves.
3. Connect the fuel hose coupling to the service valve. HAND TIGHTEN ONLY.
Make sure the coupling is not cross-threaded and check for leakage by noting any propane odours immediately after the tank is connected. This connection MUST be secure because the service valve has a safety valve inside which will only open if the fuel line fitting is completely seated into the service valve.
4. Secure the tank using the Velcro strap.
5. Fold up and secure the step down plate by replacing the pull pin.
Pressure Relief Valve
Liquid Level Sight Gauge
Bleeder Valve Service Valve
OPERATOR’S MANUAL
Page 14
Adjusting the
Handle
To remove the propane tank:
1. Turn off the service valve.
2. Follow the steps above but instead, disconnect the fuel hose coupling and remove the tank from the shroud housing.
3. Return to handle to the upright position.
CAUTION
ALWAYS open the service valve slowly to allow pressure to equalize in the hoses. Opening quickly may cause the flow check valve to engage, limiting fuel flow.
ALWAYS connect or change propane tanks in a well-ventilated area.
To adjust the handle:
A
1. On the TITAN XT Propane, firmly grasp and hold onto the handle with one hand; with the other hand pull the spring-loaded pop pin (A). Adjust the handle to the desired position and release the pop pin.
2. On the COLOSSOS XT Propane, firmly grasp and hold onto the handle with one hand; with the other hand remove the pull pin (A), adjust the handle to the desired position and replace the pull pin.
There are five positions that can be selected:
• The vertical position is used for tilting the machine back to change tooling and to maneuver the machine.
• The most forward position is used to transport, store or ship the machine.
• The three most back positions are used for selecting operating positions.
WARNING
ALWAYS make sure the pin is engaged BEFORE moving or operating the machine. Failure to check the pin is securely engaged could result in damage to the machine or injury to the operator as the handle could release unexpectedly when the machine is being operated or tilted back.
OPERATOR’S MANUAL
Page 15
Removing and
Reattaching the
Handle
Assembly
To disconnect the handle assembly:
1. Close the valve on the propane tank. Using an adjustable wrench, disconnect the fuel hose from the regulator.
2. Underneath the handle assembly, locate and disconnect the battery plug.
Regulator
Battery Plug
3. On the front of the engine, disconnect the throttle linkage by gently pulling on the linkage.
4. On the ECU control box, disconnect the 8-pin connector.
Throttle Linkage
8-Pin Connector
5. Unscrew the two bolts attaching the handle assembly frame to the main body of the machine.
Bolts
6. Roll the handle assembly away from the main body.
To reattach the handle assembly: reverse the order of the steps above.
OPERATOR’S MANUAL
Page 16
Attaching the
Vacuum Hose
To attach the vacuum hose:
1. Attach a standard 2” vacuum hose to the left, the right, or both vacuum ports.
2. Always refer to the vacuum manual for operating procedures.
Vacuum Port
Vacuum Port
Starting the
Machine
WARNING
DO NOT TILT THE MACHINE BACK WHILE STARTING. Doing so can cause the tooling to release from the machine and cause damage to the floor and harm
to the operator.
1. Start in the IDLE ‘SLOW’ throttle position. This creates a vacuum
necessary to open the lock-off valve inside the regulator. Activating the
throttle lever will keep the lock-off valve from opening and the engine from
getting fuel so the engine will not start. Proper maintenance will insure
easy starting.
2. Open the service valve on the propane tank about one and a half turns.
3. Turn on the ignition key. The yellow light on the handle will turn on.
4. Push green START button for a MAXIMUM of 5 to 6 seconds or until the engine fires. Serious starter damage will result if this is exceeded and may void warranty.
5. Operate the engine at half throttle for approximately two minutes for proper warm-up.
IMPORTANT
If the engine refuses to start see the Troubleshooting Guide page 27.
OPERATOR’S MANUAL
Page 17
Adjusting the
Speed
Activating the
Tooling
Stopping the
Engine
To increase the speed, pull the throttle lever towards you. To decrease the speed, push the throttle lever away from you. The RPM will be displayed on the digital tachometer on the handle.
To engage disks, gently squeeze the left, the right, or both clutch activation levers. ALWAYS keep the machine moving while the tooling is engaged. To disengage the disks on the TITAN XT Propane, release one clutch activation lever. To disengage disks on the COLOSSOS XT Propane release both clutch activation levers.
1.
Close the service valve on the propane tank.
2.
ALWAYS allow the engine to run until it stops from lack of fuel.
Stopping the
Machine
3.
The emergency stop button should be used ONLY IN AN EMERGENCY.
To stop the machine, turn the ignition key OFF. Ensure the yellow light is off.
OPERATOR’S MANUAL
Page 18
MAINTENANCE
General
Recommended
Maintenance Items
Daily
Weekly
Monthly
Fuel control system: To ensure personal safety, adjustments should ONLY be made by a qualified LPG system technician or an authorized service center using an exhaust gas analyzer. DO NOT operate the machine if carbon monoxide levels exceed OSHA/WCB/local standards.
• Change engine oil.
•
Check pad driver for loose parts.
• Check wheel bolts.
• Check engine mount bolts.
•
Check handle bolts
• Check for leakage of engine oil at the various seals.
DO NOT exceed the 100 hours oil change interval. Oil changes more frequent than 100 hours will give even longer engine life.
• Wipe down the machine after every job.
• Gently remove dirt and debris from the Velcro hook material using a wire brush. This will ensure maximum adhesion.
• Check the Rear Pivoting Assembly (RPA) bolts are tight.
• Vacuum the underside of machine
• Check all fasteners and tighten if necessary.
• Remove pad drivers and wipe down bearing shields with a damp cloth. DO
NOT use sharp objects or abrasive pads to clean the bearing shields. This can compromise the bearing seal. Re-install pad drivers using a generous amount of blue thread locking compound.
• Using a soft scrub pad, remove any excess dirt build-up from the bottom plate and back side of the pad drivers.
•
DO NOT use an abrasive material on the silicone seals around the vacuum tubes. If the silicone seal is damaged, degrease affected area and apply silicone sealer over the damaged area. Failure to inspect the seal could lead to drive train contamination and possible drive train failure.
• Check all strain reliefs and make sure they are tight. (Strain reliefs are the plastic nuts that secure the wires that come out of the handle)
• Remove pad drivers and inspect threads to make sure that there are no signs of cross threading or stripping. Remove excess thread locking compound from bolts using a wire brush or by washing the bolts in a solvent. Re-install pad drivers using a generous amount of blue thread locking compound.
• Clean and lubricate the wheels.
• Using an extremely light abrasive pad, remove any topical rust from the shafts.
OPERATOR’S MANUAL
Page 19
WARNING
Prevent accidental starting during engine service by removing the spark plug caps.
NOTE: The service intervals can be used as a guide. Service more frequently as necessary, depending on operating conditions.
K
Service to be preformed by an authorized Kawasaki dealer.
MAINTENANCE
TITAN XT PROPANE MAINTENANCE CHART
Check and add engine oil
Daily First
8 hrs
Every
25 hrs
INTERVAL
Every
50 hrs
Every
100 hrs
Every
200 hrs
Check for loose or lost
nuts, screws and bolts
Check for fuel and oil
leakage
Check battery electrolyte
level
Every
250 hrs
screen
element
element
K cylinder/cylinder head fins
Tighten nuts and screws
Change engine oil
Clean and re-gap spark
plugs
Change oil filter
element
K
Clean combustion chamber
K
Check and adjust valve
clearance
K
Clean and lap valve seating
surface
Every
300 hrs
OPERATOR’S MANUAL
Page 20
WARNING
Prevent accidental starting during engine service by removing the spark plug caps.
NOTE: The service intervals can be used as a guide. Service more frequently as necessary, depending on operating conditions.
K
Service to be preformed by an authorized Kawasaki dealer.
COLOSSOS XT PROPANE MAINTENANCE CHART
MAINTENANCE
Check and add engine oil
Daily First
8 hrs
Every
25 hrs
INTERVAL
Every
100 hrs
Every
200 hrs
Every
250 hrs
Every
300 hrs
Check for loose or lost
nuts, screws and bolts
Check for fuel and oil
leakage
Check battery electrolyte
level
screen
element
element
K cylinder/cylinder head fins
Tighten nuts and screws
Change engine oil
Clean and re-gap spark
plugs
Change oil filter
element
K
Clean combustion chamber
K
Check and adjust valve
clearance
K
Clean and lap valve seating
surface
Replace air cleaner foam
element
Every
500 hrs
OPERATOR’S MANUAL
Page 21
Plug ‘N Go Tooling
Indexing
WerkMaster’s patent pending ULTRA-FLEX Plug ‘N Go Tooling System is a major advancement in tooling design. WerkMaster machines not only flatten a floor, but they also follow a very wavy, uneven floor using the same tools and drive plates on all floor surfaces. Using various hardness rubber grommets, bumpers and INDEXING, no need to add heavy weights, simply increase or reduce point pressure by easily adding or removing Plug ‘N Go segments.
Eliminates the frustration and pain of dealing with lippage, expansion joints, large cracks.
Indexing is a function of our ULTRA-FLEX Plug ‘N Go tooling system. It allows the operator to adjust the Plug ‘N Go plates to a RIGID or FLEX mode. RIGID mode is used to flatten floors. FLEX mode allows the operator to follow the contours and undulations of the floor eliminating tool marks and optimizing the finish.
Stoppers Stoppers
DO NOT align with
align with holes
holes
RIGID MODE FLEX MODE
RIGID mode is when the stoppers do not line up the holes in the Plug ‘N Go plate. This makes for a firm, almost inflexible movement of the plate.
To adjust to RIGID mode:
1. Turn off the service valve. Allow the engine to stop and turn the ignition key
OFF.
2. Remove the propane tank and put the machine in the EZ Bak position.
3. Remove one of the Plug ‘N Go plates. Turn the plate 180° so that the stoppers DO NOT line up with the holes in the plate. Do the same for each of the 8 heads.
4. Slowly return the machine to the upright position; replace the propane tank.
FLEX mode is when the stoppers line up with the holes in the Plug ‘N Go plate.
This makes for a flexible plate that can conform to the work surface.
To adjust to FLEX mode:
1. Turn off the service valve. 2. Allow the engine to stop and turn the ignition key
OFF.
2. Remove the propane tank and put the machine in the EZ Bak position.
3. Remove one of the Plug ‘N Go plates. Turn the plate 180° so that the stoppers line up with the holes in the plate. Do the same for each of the 8 heads.
4. Slowly return the machine to the upright position; replace the propane tank.
OPERATOR’S MANUAL
Page 22
Installing and
Removing the Pad
Driver
Rotation Pattern of
Tooling Plates
To install and remove the pad driver on the bottom of your machine, you will need a 9/16” socket wrench, a soft face mallet, and some medium strength thread locker (blue Loctite 243 or equivalent).
Pad Driver Bolt
To remove the pad driver:
1. Slip the socket wrench over the pad driver bolt and strike the wrench with the soft face mallet in a counter-clockwise direction.
2. When installing a new pad driver or re-installing an existing one, apply a generous amount of thread locker compound to the end of the bolt and fit it through the hole in the pad driver. Reapply thread locking compound every time a pad driver is removed.
3. Line up the bolt to the threaded end of the shaft and start the first couple of threads.
4. Once the bolt is engaged, make sure that the drive shaft tongue is properly seated within the pad driver’s slot before tightening the bolt all the way.
5. Slip the socket wrench over the pad driver bolt and strike the wrench with the soft face mallet in a clockwise direction.
CAUTION
Failure to seat the pad driver correctly on the shaft could result in the pad driver slot being stripped out, the threads in the shaft being stripped, the machine leaving heavy tool marks, and the tooling overheating.
Discs 1, 2, 3 and 4 rotate clockwise
Discs 5, 6, 7 and 8 rotate counter-clockwise
View of WerkMaster from the bottom with numbered discs and clockwise and counter-clockwise labelling.
OPERATOR’S MANUAL
Page 23
Changing
The Oil
Installing and
Removing the Battery
The battery is located in the shroud housing beneath the propane tank and is covered with a black rubber mat.
To remove and install the battery:
1. Stop the engine and turn the ignition key OFF.
2. Undo the Velcro strap that secures the propane tank in position.
3. Disconnect and remove the tank.
4. Lift the black rubber mat. Unscrew the M6 hex nuts from the posts and remove the rubber bar holding the battery in place.
5. Disconnect the battery by removing the BLACK negative (-) cable first, then the RED positive (+) cable.
6. Remove the battery from its housing and replace with a new battery.
7. Connect the new battery by reconnecting the RED positive (+) cable, then the BLACK negative (-) cable. Make sure all connections are tight.
8. Replace the rubber bar and screw on the hex nuts to the posts. Replace the black rubber mat.
9. Insert and connect the propane tank and secure in position with the Velcro strap.
WARNING
Hot oil can cause severe burns. Be careful when changing the oil.
Dispose of used oil properly.
The oil should be changed after the first 8 hours and then every 100 hours.
To change the oil:
1. Move the machine to a level surface.
2. Start and warm the machine so the oil will drain easily and completely.
3. Stop the engine and turn the ignition key OFF.
4. Slowly remove the drain plug and let the oil drain into a suitable container.
It may be necessary to loosen the fill cap in order for the oil to drain.
Drain Plug
OPERATOR’S MANUAL
Page 24
5. When the oil has drained, replace the drain plug.
6. Remove the oil fill cap and add clean SH or SJ SAE30 oil.
For the TITAN XT Propane use:
• 1.6 US qt (1.5 L) when the filter is not changed
• 1.8 US qt (1.7 L) when the filter is changed.
For the COLOSSOS XT Propane use:
7. Run the engine at slow idle for 2 minutes. Stop the engine and check the
oil level. Add oil if needed.
•
2.2 US qt (2.1 L) when the filter is not changed
• 2.4 US qt (2.3 L) when the filter is changed.
Changing the
Oil Filter
WARNING
Be careful when draining hot oil; it can cause severe burns.
Engine oil is toxic. Dispose of used oil properly.
Change the oil filter after every 200 hours of operation.
Oil Filter
To change the oil filter:
1. Move the machine to a level surface.
2. Start and warm the machine so the oil will drain easily and completely.
3. Stop the engine and turn the ignition key OFF.
4. Drain engine oil into suitable container.
5. Place a suitable container under the filter connection. Remove the oil filter by turning counter-clockwise.
6. Coat the seal of the new filter with clean engine oil.
7. Install the new filter by turning clockwise until the seal contacts the mounting.
Give the filter a further 2/3 turn BY HAND.
OPERATOR’S MANUAL
Page 25
Changing the
Air Filter
8. Fill with new oil.
9. Run the engine for 3 minutes; stop the engine and check for leaks.
10. Check oil level. Add oil if necessary.
WARNING
DO NOT run the engine with the air filter removed.
TITAN XT Propane Air Filter COLOSSOS XT Propane Air Filter
To change the air filter:
1. On the TITAN XT Propane, unscrew the two screws securing the air filter cover.
2. Remove the paper and foam elements by pulling them out.
3. Replace with new filters, replace the cover and secure by replacing the screws.
1. On the COLOSSOS XT Propane, push open the cap on the case of the air
filter body to expel dust and/or water accumulated inside.
2. Unfasten the two retaining clamps and remove the case from the air filter.
3. Remove the paper and foam elements by pulling them out.
4. Replace with new filters, reinstall case and fasten retaining clamps
DO NOT clean, wash, oil or use pressurized air on the air filter. Replace, do not clean, the air filter.
OPERATOR’S MANUAL
Page 26
TROUBLESHOOTING
PROBLEM
Engine is hard to start.
Engine will not start.
POSSIBLE CAUSE
Propane cylinder is not properly connected.
Battery is weak.
Oil level is too low.
Insufficient vacuum.
Coil air gap out of adjustment.
Spark plug or head bolts loose.
Head gasket blown or valves need adjusting.
Propane cylinder is empty.
Oil level is low.
Dead battery..
Plug between starter and battery (located under handle) is not connected.
Insufficient vacuum.
Head gasket is blown or valves need adjusting.
Wires broken or disconnected.
Coil(s) defective.
Spark plug gap is incorrect.
Spark plug is defective.
ClearSKY shut the machine down.
Insufficient vacuum.
Engine lacks power.
Dirty air filter(s).
Head gasket leaking.
No compression.
Fuel mixture is too lean.
Valves need adjusting or replacing.
Surging idle.
Engine starts and idles but quits as the throttle is advanced.
Starter barely turns the engine over.
Solenoid just clicks
Engine stops running.
Propane tank not properly connected.
Battery is weak.
Battery is weak.
Propane cylinder is empty.
Engine oil level is low.
Dirty air filter.
ClearSKY shuts the machine down.
Clutch will not engage.
Engine begins to backfire regularly, suddenly
Loose connection.
Clutch is bad.
Spark plug is damaged.
SOLUTION
Check connection and open service valve slowly.
Charge or replace battery.
Check the oil level and add oil if needed.
Put the engine throttle in the idle ‘slow’ position.
Adjust coil air gap. Have the machine serviced by an authorized
Kawasaki dealer.
Re-torque. Have the machine serviced by an authorized Kawasaki dealer.
Replace head gasket. Adjust valves, replace if necessary. Have the machine serviced by an authorized Kawasaki dealer.
Installed properly filled cylinder.
Check the oil level and add oil if needed.
Replace battery.
Connect starter plug to battery.
Place the engine throttle in the idle ‘slow’ position.
Check the regulator vacuum hose for breaks, pinched hose, or a bad connection.
Replace head gasket, adjust valves and replace if necessary. Have the machine serviced by an authorized Kawasaki dealer.
Reconnect or replace wires.
Replace coil. Have the machine serviced by an authorized Kawasaki dealer.
TITAN XT Propane: Adjust gap to 0.025 in (0.64 mm).
COLOSSOS XT Propane: Adjust gap to 0.030 in (0.75 mm)
Replace spark plug.
If the light is on, turn the key switch off and wait 30 seconds. Try again.
Put the engine throttle in the idle ‘slow’ position.
Check the regulator vacuum hose for breaks, pinched hose, or a bad connection.
Clean or replace the primary filter (paper element).
Clean or replace the secondary filter (foam element).
Replace head gasket. Have the machine serviced by an authorized
Kawasaki dealer.
Worn piston ring(s) and/or cylinder head(s) need replacing. Have the machine serviced by an authorized Kawasaki dealer.
Check and if necessary adjust fuel mixture.
Adjust valves. Have the machine serviced by an authorized
Kawasaki dealer.
Have the machine serviced by an authorized Kawasaki dealer.
Check the service valve. Contact Technical Support: 866.373.9375.
Check the charge on the battery. Recharge or replace if needed.
Check the charge on the battery. Recharge or replace if needed.
Install properly filled cylinder.
Check the oil level and oil if needed.
Clean both filters and if necessary replace.
Check close loop vacuum line.
Clean air filters and if necessary replace.
Check for any loose wiring or fuel line connections.
Service machine and check fuel settings.
Check wiring for bad connection or broken wire.
Replace if necessary. Contact Technical Support: 866.373.9375.
Check the spark plug boots for cracks. Remove the spark plug lead from the spark plug and replace the boot. Contact Technical Support:
866.373.9375.
OPERATOR’S MANUAL
Page 27
EXPLODED VIEW AND PARTS LIST – TITAN XT PROPANE
OPERATOR’S MANUAL
Page 28
2
1
1
4
1
1
2
1
2
1
2
1
1
1
4
8
1
1
1
1
1
1
4
4
48
8
16
16
2
16
24
16
12
8
1
1
48
1
1
8
1
11
7
1
1
1
3
1
1
8
8
1
1
1
1
2
1
1
1
QTY
2
17
11
7
54
55
56
57
58
59
60
45
46
47
48
49
50
51
52
53
61
62
63
36
37
38
39
40
41
42
43
44
27
28
29
30
31
32
33
34
35
20
21
22
23
24
25
26
13
14
15
16
17
18
19
5
6
7
8
9
10
11
12
ITEM
1
2
3
4
TITAN XT PROPANE PARTS LIST
PART NUMBER DESCRIPTION
008-0310-01
110-0097-00
540-0277-00
500-0252-00
540-0070-00
510-0021-00
540-0278-00
510-0038-00
590-0112-00
590-0189-00
540-0286-00
540-0192-00
540-0071-00
590-0250-00
100-0809-00
590-0240-00
590-0238-00
580-0095-00
590-0237-00
590-0159-00
008-0208-00
008-0154-00
008-0189-00
590-0128-00
008-0363-01
008-0357-00
008-0358-00
580-0033-00
590-0182-00
008-0362-00
008-0142-03
590-0019-00
120-0049-00
540-0311-00
550-0024-00
590-0040-00
590-0065-00
110-0088-00
500-0013-00
590-0140-00
500-0264-00
500-0265-00
550-0007-00
500-0248-00
500-0256-00
500-0006-00
100-0628-00
100-0627-00
520-0041-00
100-0585-01
100-0629-00
590-0120-00
100-0651-00
590-0245-00
590-0169-00
008-0343-00
590-0260-00
590-0261-00
590-0142-00
100-0725-00
590-0114-00
590-0124-00
520-0040-00
Vacuum Tube Assembly
Bearing
Fastener
Sprocket
Sprocket
Key Stock
Bushing
Sprocket
Bearing
Idler Shaft Spacer
Offset Idler Shaft
Belt
Bearing Plate
Spacer
Fastener
Idler Wrench
Fastener
Fastener
Weather Strip
Fastener
Nut
Washer
Belt Access Plate
Fastener
Fastener
Belt
Fastener
Bumper
Bumper
Grommet
Fastener
Pad Driver
Loop
Dust Skirt
Magnet
Fastener
Plate
Shear Pins
Fastener
Engine
Clutch
Key
Fastener
Washer
Suspension Foam
Cover Assembly
Enclosure
Sprocket
Strain Relief
Soft Start Module
Circuit Breaker
Emission Control Unit
Fastener
Fastener
Pin Power Connector Set
Pin Power Connector Set
Strain Relief
Washer
Engine Sleeve
Washer
Fastener
Wheel
Fastener
OPERATOR’S MANUAL
Page 29
108
109
110
111
112
113
114
115
116
117
118
119
120
99
100
101
102
103
104
105
106
107
90
91
92
93
94
95
96
97
98
83
84
85
86
87
88
89
76
77
78
79
80
81
82
68
69
70
71
72
73
74
75
ITEM
64
65
66
67
121
2
1
1
1
1
2
1
2
2
1
1
2
8
8
1
1
1
1
1
8
1
1
4
1
1
2
1
1
2
2
2
1
1
1
1
2
1
1
1
1
1
1
2
1
2
1
1
1
1
1
2
1
2
2
QTY
1
2
2
1
580-0107-00
540-0240-00
590-0234-00
590-0232-00
510-0012-00
100-0713-00
540-0241-00
590-0048-00
510-0033-00
590-0133-00
510-0063-00
580-0114-00
590-0115-00
580-0104-00
100-0741-00
100-0742-00
120-0051-00
510-0058-00
510-0062-00
510-0026-00
590-0273-00
540-0194-00
590-0274-00
100-0747-00
590-0113-00
130-0114-00
120-0050-00
540-0175-00
540-0176-00
590-0190-00
008-0354-01
008-0361-00
PART NUMBER
580-0070-00
590-0192-00
590-0263-00
540-0271-00
540-0147-00
540-0005-00
540-0236-00
540-0193-00
540-0179-01
580-0204-00
590-0242-00
590-0259-00
540-0234-00
590-0214-00
580-0112-00
590-0212-00
100-0343-02
100-0687*0
580-0122-00
540-0144-00
100-0215-01
130-0115-00
580-0088-00
100-0726-00
130-0117-00
540-0179-00
DESCRIPTION TITAN XT PROPANE cont’d
Pin
Fastener
Fastener
Hour Meter/Tachometer
Button
Button
Light
Ignition Switch
Bumper
Cable
Fastener
Fastener
Switch
Fastener
Spring
Fastener
Clutch Lever Plate
Handle Junction Box
Handle Grip
Strain Relief
Handle Cover Plate
Handle Assembly
Handle
Protection Plate
Main Frame Assembly
Bumper
Key Ring
Bumper
Washer
Washer
Propane Tank
Control Box Mounting Block
Battery
Fastener
Rubber Battery Bar
Fastener
Rubber Mat
Strap
Fastener
Chain
Drive Train Lower Plate
Drive Train Upper Plate
Shroud Assembly
Hose
Hose Fitting
Hose Fitting
Screw
Plug
Fastener
Regulator Mount Plate
Fastener
Handle Posts
Engine Mount Adapter Assembly
Strain Relief
Strain Relief
Fastener
Plate Assembly
Plate Assembly
OPERATOR’S MANUAL
Page 30
EXPLODED VIEW AND PARTS LIST – COLOSSOS XT PROPANE
OPERATOR’S MANUAL
Page 31
54
55
56
57
58
59
60
45
46
47
48
49
50
51
52
53
61
62
63
36
37
38
39
40
41
42
43
44
27
28
29
30
31
32
33
34
35
20
21
22
23
24
25
26
13
14
15
16
17
18
19
5
6
7
8
9
10
11
12
ITEM
1
2
3
4
2
2
1
1
1
1
1
1
2
2
1
1
1
1
2
1
1
1
1
8
2
2
1
1
2
1
17
8
1
1
1
1
2
1
2
1
1
1
1
1
1
7
1
1
1
1
2
2
8
1
1
1
8
1
1
8
8
1
1
QTY
16
24
16
16
COLOSSOS XT PROPANE PARTS LIST
PART NUMBER DESCRIPTION
500-0249-01
510-0013-00
510-0021-00
510-0026-00
510-0032-00
510-0033-00
510-0038-00
510-0058-00
510-0062-00
520-0041-00
520-0043-00
530-0034-00
540-0005-00
540-0070-00
540-0071-00
540-0144-00
540-0147-00
540-0179-00
540-0179-01
130-0078-01
130-0083-01
130-0085-01
100-0605-00
100-0606-01
100-0607-00
100-0609-02
100-0611-00
100-0615-02
130-0080-01
100-0687-00
500-0013-00
500-0091-00
500-0191-00
500-0197-00
500-0198-00
500-0247*00
500-0248-00
008-0143-03
008-0154-00
008-0189-00
008-0208-00
008-0309-01
008-0310-01
008-0319-00
008-0320-00
008-0359-02
008-0360-00
100-0120-01
130-0082-01
100-0176-00
100-0215-01
120-0017-02
100-0328-01
100-0392-00
110-0073-00
100-0555-01
100-0578-01
100-0579+01
100-0580-01
110-0079-01
100-0584-01
100-0585-01
120-0031-01
Screw
Bumper
Grommet
Bumper
Dust Skirt
Suspension Foam
Weather Strip
Velcro Loop
Pad Driver Plate
Plate
Idler Shaft Spacer
Handle Tube Assembly
Spacer
Handle Cover Plate
Engine Mounting Adapter Assembly
Access Plate
Regulator Mount
Vacuum Tube Assembly
Hitch
Drive
Drive Train Lower Plate
Drive Train Upper Plate
Cover Assembly
Drive Shaft
Bearing Plate
Shroud Assembly
Handle
Handle
Handle
Motor Sleeve
Handle Protection Plate
Handle Wheel Axle
Offset Idler Shaft
Idler Wrench
Cable Bracket
Handle
Handle Junction Box
Bearing
Bushing
Sprocket
Bearing
Bearing
Sprocket
Bushing
Sprocket
Propane Tank
Soft Start Module
Hose Fitting
Rubber Mat
Rubber Bar
Emission Control Unit
Hose
Hose Fitting
Belt
Belt
Engine
Button
Strain Relief
Strain Relief
Strain Relief
Button
Bumper
Bumper
OPERATOR’S MANUAL
Page 32
117
118
119
120
121
122
123
108
109
110
111
112
113
114
115
116
99
100
101
102
103
104
105
106
107
90
91
92
93
94
95
96
97
98
83
84
85
86
87
88
89
76
77
78
79
80
81
82
68
69
70
71
72
73
74
75
ITEM
64
65
66
67
124
4
1
1
2
4
1
1
1
2
2
2
4
2
2
48
4
5
2
2
8
2
3
1
11
8
1
16
4
10
8
4
12
2
9
4
2
1
2
2
1
1
1
1
8
1
48
2
2
1
1
1
2
1
1
1
1
1
QTY
1
1
2
2
590-0171-00
590-0182-00
590-0189-00
590-0190-00
590-0192-00
590-0194-00
590-0212-00
590-0214-00
590-0230-00
590-0232-00
590-0237-00
590-0238-00
590-0240-00
590-0242-00
590-0244-00
590-0245-00
590-0259-00
590-0055-00
590-0112-00
590-0114-00
590-0120-00
590-0124-00
590-0128-00
590-0132-00
590-0133-00
590-0135-00
590-1036-00
590-0140-00
590-0142-00
590-0143-00
590-0146-00
590-0147-00
590-0159-00
590-0166-00
590-0169-00
PART NUMBER
540-0192-00
540-0193-00
540-0194-00
540-0234-00
540-0236-00
540-0238-01
540-0240-00
540-0241-00
540-0271-00
540-0277-00
540-0278-00
540-0286-00
550-0007-00
550-0022-00
550-0024-00
580-0033-00
580-0095-00
580-0098-00
580-0104-00
580-0107-00
580-0111-00
580-0114-00
580-0122-00
580-0190-00
590-0000-00
590-0048-00
Fastener
Fastener
Fastener
Fastener
Fastener
Fastener
Fastener
Fastener
Washer
Washer
Fastener
Fastener
Washer
Fastener
Fastener
Fastener
Fastener
Fastener
Fastener
Fastener
Fastener
Fastener
Fastener
Fastener
Fastener
Fastener
Fastener
Fastener
Washer
Washer
Washer
Washer
Fastener
Fastener
Fastener
DESCRIPTION COLOSSOS XT PROPANE cont’d
Pin Power Connector Set
Switch
Plug
Switch
Light
Clutch
Bumper
Battery
Tachometer
Enclosure
Circuit Breaker
Pin Power Connector Set
Key Stock
Key
Key
Magnet
Wheel
Retaining Ring
Chain
Key Ring
Throttle
Cinching Strap
Handle Grip
Quick Release Pin
Washer
Fastener
OPERATOR’S MANUAL
Page 33
WARRANTY INFORMATION
Terms & Conditions
Delivery, Damages,
Shortages
WerkMaster Grinders & Sanders Inc., herein referred to as WerkMaster, warrants that each new machine manufactured by WerkMaster to be free from defects in material and workmanship in normal use and service for a period of (3) three years from date of shipment to the original Purchaser or Distributor.
Accessories or equipment furnished and installed on the product by WerkMaster but manufactured by others, including but not limited to engines, motors, electrical components, transmissions, etc. such as the Kawasaki motor, shall carry the accessory manufacturer’s own warranty.
WerkMaster will, at its option, repair or replace, at a WerkMaster factory or a point designated by WerkMaster, any part, which shall appear to the satisfaction of WerkMaster inspection, to have been defective in material or workmanship.
WerkMaster reserves the right to modify, alter and improve any part or parts without incurring any obligation to replace any part or parts previously sold without such modified, altered or improved part or parts.
This warranty is in lieu of and excludes all other warranties, expressed, implied, statutory, or otherwise created under applicable law including, but not limited to the warranty of merchantability and the warranty of fitness for a particular purpose. In no event shall the Seller or the Manufacturer of the product be liable for special, incidental, or consequential damages, including loss of profits, whether or not caused by or resulting from the negligence of the Seller and/or the
Manufacturer of the product unless specifically provided herein.
In addition, this warranty shall not apply to any products or portions thereof which, at WerkMaster’s discretion, have been subjected to abuse, misuse, improper installation, maintenance, or operation, electrical failure or abnormal conditions, and to products which have been tampered with, altered, modified, repaired, reworked by anyone not approved by the seller, or used in any manner inconsistent with the provisions of the above or any instructions or specifications provided with or for the product.
Except for conditions or warranties, which may not be excluded by law, the Seller makes no warranty of its own on any item warranted by WerkMaster, and makes no warranty on other items unless it delivers to the Purchaser a separate written warranty document specifically warranting the item. The Seller has no authority to make any representation or promise on behalf of WerkMaster or to modify the terms or limitations of this warranty in any way.
Seller shall use reasonable efforts to attempt to cause the Products to be delivered as provided for in these Terms & Conditions. Delivery to the initial common carrier shall constitute the delivery to the Purchaser. Seller’s responsibility, in so far as transportation risks are concerned, ceases upon the delivery of the Products in good condition to such carrier at the F.O.B. point and all the Products shall be shipped at the Purchaser’s risk. Seller shall not be responsible or liable for any loss of income and/or profits, or incidental, special, consequential damages resulting from Seller’s delayed performance in shipment and delivery.
OPERATOR’S MANUAL
Page 34
Return of Defective
Products
FORCE MAJEURE
Defective or failed material shall be held at the Purchaser’s premises until authorization has been granted by Seller to return or dispose of Products.
Products that are to be returned for final inspection must be returned Freight
Prepaid in the most economical way. Credit will be issued for material found to be defective upon Seller’s inspection based on prices at time of purchase
Seller’s obligation hereunder are subject to, and Seller shall not be held responsible for, any delay or failure to make delivery of all or any part of the
Product due to labor difficulties, fires, casualties, accidents, acts of the elements, acts of God, transportation difficulties, delays by a common carrier, inability to obtain Product, materials or components or qualified labor sufficient to timely perform part of or all of the obligations contained in these terms and conditions, governmental regulations or actions, strikes, damage to or destruction in whole or part of manufacturing plant, riots, terrorist attacks or incidents, civil commotions, warlike conditions, flood, tidal waves, typhoon, hurricane, earthquake, lightning, explosion or any other causes, contingencies or circumstances within CANADA not subject to the Seller’s control which prevent or hinder the manufacture or delivery of the Products or make the fulfillment of these terms and conditions impracticable. In the event of the occurrence of any of the foregoing, at the option of Seller, Seller shall be excused from the performance under these Terms and Conditions, or the performance of the Seller shall be correspondingly extended. This document sets forth the terms and conditions pursuant to which the purchaser (“Purchaser”) will purchase and
WerkMaster Grinders and Sanders Inc. (“Seller”) will sell the products, accessories, attachments (collectively “the Products”) ordered by the Purchaser.
These terms and conditions shall govern and apply to the sale of Seller’s
Products to Purchaser, regardless of any terms and conditions appearing on any purchase order or other forms submitted by Purchaser to Seller, or the inconsistency of any terms therein and herein.
To get the best protection from your WerkMaster Warranty be sure to register your product(s) online at http://www.werkmaster.com/warranty .
WerkMaster Grinders and Sanders Inc.
6932 Greenwood Street, Burnaby, BC V5A 1X8 tel: 604.629.8700 | toll free: 1.866.373.WERK | fax: 604.444.4231 www.werkmaster.com | email: [email protected]
OPERATOR’S MANUAL
Page 35
Operation and Safety Guide
TITAN XT PROPANE
TM
Vendor Website: www.werkmaster.com
Technical Support: 866-373-9375
Tool Application:
The TITAN XT PROPANE
TM
can be used to grind and/or polish various floor surfaces.
C E
SAFETY TOPICS:
Read the Operator’s Manual or the
Operation and Safety Guide and all
attempting to operate WerkMaster machines. Failure to follow the safety precautions could result in severe personal injury or death.
SAFETY CHECKLIST:
WARNING
: ALWAYS turn off the machine when changing discs/tooling,
before servicing, and when not in use.
1. Before starting the machine do a check for loose, cracked or worn parts,
propane tank are secure and that all connections are properly fitted.
2. Ensure the work area is properly ventilated, particularly if working in a small, closed-in area.
cigarette lighters, pilot lights or any other source of ignition may cause an
sources of ignition should be
D
B A
Fig 1 Fig 2 Fig 3
Tool Operation:
Step
Action
1
Ensure the handle is in its full upright position (Fig1). Tilt the equipment back by releasing the step down plate (A). While stepping on the step down plate, pull down on the handle. Choose the appropriate tooling holder attachment – 8” magnetic Plug ‘N Go plate for metal bond tools or 8” Foam/Velcro Adapter plate. Insert the 2 shear pins into the rubber grommets. Then attach the corresponding tooling to the plates (E).
2
Lift the equipment back to the upright position using the step down plate to prevent the TITAN XT Propane from hitting the floor. Loosen and lower the dust skirt (B) so that it is just above the working surface.
3
Adjust the handle to a comfortable operating position by pulling out and re-inserting the release pin at the swivel joint (C). Connect the vacuum hose(s) to the vacuum pipes (D) located on either side. area. DO NOT smoke in the vicinity of propane.
4. Never operate the machine under the influence of drugs or alcohol or when extremely fatigued.
5. If the equipment doesn’t start or stops unexpectedly first check your propane
www.werkmaster.com
or call Technical
Support: 866.373.9375.
WARNING
: Never turn on the equipment while it is tilted back. Any
could eject and become a lethal projectile.
Wear appropriate personal safety
4
Ensure the machine is in the IDLE throttle position. Open the service valve on the propane tank about one and a half turns. Turn the key ON and push the GREEN start button. The yellow light on the handle will come on. Engage the clutch by squeezing the left, the right, or both activation levers.
5 Stop the engine by shutting off the service valve on the propane tank.
ALWAYS allow the engine to run until it stops from lack of fuel.
6 Stop the machine by turning the ignition key OFF. Ensure the yellow light is off.
7
When the equipment is in operation it should move smoothly and without chattering. If chattering or excessive vibration occurs stop the machine, turn it off, tilt it back and verify that all the Plug ‘N Go/Adaptor plates are installed correctly and the tooling is seated properly.
8
Move the equipment continuously in any direction using a circular motion. Be sure keep it moving at all times to prevent unwanted marks.
View training videos at www.werkmaster.com
.
OPERATOR’S MANUAL
Page 36
Operation and Safety Guide
COLOSSOS XT PROPANE
TM
Vendor Website
:
www.werkmaster.com
Technical Support: 866-373-9375
Tool Application:
The COLOSSOS XT PROPANE
TM
can be used to grind and/or
SAFETY TOPICS:
polish various floor surfaces.
D
E
Read the Operator’s Manual or the
Operation and Safety Guide and all the safety precautions before attempting to operate WerkMaster machines. Failure to follow the safety precautions could result in severe personal injury or death.
SAFETY CHECKLIST:
WARNING
: ALWAYS turn off the machine when changing discs/tooling, before servicing, and when not in use.
1. Before starting the machine do a check for loose, cracked or worn parts, oil levels, leaks, that the handle and propane tank are secure and that all connections are properly fitted.
2. Ensure the work area is properly ventilated, particularly if working in a small, closed-in area.
3. Propane is highly flammable, so cigarette lighters, pilot lights or any other source of ignition may cause an explosion if in contact with propane. All sources of ignition should be extinguished or removed from the work area. DO NOT smoke in the vicinity of propane.
4. Never operate the machine under the influence of drugs or alcohol or when extremely fatigued.
5. If the equipment doesn’t start or stops unexpectedly first check your propane tank and the connections then go to www.werkmaster.com
or call Technical
Support: 866.373.9375.
WARNING
: Never turn on the equipment while it is tilted back. Any discs/tooling attached to the bottom could eject and become a lethal projectile.
Wear appropriate personal safety equipment such as hearing and eye protection and a dust mask or respirator.
B C
A
Fig 1 Fig 2 Fig 3
Tool Operation:
Step
Action
1
Ensure the handle is in its full upright position (Fig1). Tilt the equipment back by releasing and unfolding the step down plate (A). While stepping on the step down plate, pull down on the handle. Choose the appropriate tooling holder attachment – 8” magnetic Plug ‘N Go plate for metal bond tools or 8” Foam/Velcro Adapter plate. Insert the 2 shear pins into the rubber grommets. Then attach the corresponding tooling to the plates (E).
2
Lift the equipment back to the upright position using the step down plate to prevent the COLOSSOS XT Propane from hitting the floor.
Loosen and lower the dust skirt (B) so that it is just above the working surface.
3
Adjust the handle to a comfortable operating position by pulling out and re-inserting the pull pin at the swivel joint (D). Connect the vacuum hose(s) to the vacuum ports (C) located on either side of the machine.
4
Ensure the machine is in the SLOW IDLE throttle position. Open the service valve on the propane tank about one and a half turns. The yellow light on the handle will illuminate. Turn the ignition key ON and push the GREEN start button. The yellow light on the handle will come on. Engage the clutch by squeezing the left, the right, or both activation levers.
5 Stop the engine by shutting off the service valve on the propane tank.
ALWAYS allow the engine to run until it stops from lack of fuel.
6 Stop the machine by turning the ignition key OFF. Ensure the yellow light is off.
7
When the equipment is in operation it should move smoothly and without chattering. If chattering or excessive vibration occurs stop the machine, turn it off, tilt it back and verify that all the Plug ‘N Go/Adaptor plates are installed correctly and the tooling is seated properly.
8
Move the equipment continuously in any direction using a circular motion. Be sure keep it moving at all times to prevent unwanted marks.
View training videos at www.werkmaster.com
.
OPERATOR’S MANUAL
Page 37
Λήψη
Δημόσιος σύνδεσμος ενημερώθηκε
Ο δημόσιος σύνδεσμος για τη συνομιλία σας ενημερώθηκε. You may view and manage your chat links after registration here.
Δημόσιος σύνδεσμος εγγράφου
Διαφήμιση
